Will Draw-Tite Trailer Hitch Fit a 2022 Honda CR-V Hyrbid

Question

Question:

Will the Draw-Tite hitch fit my 2021 Honda CR-V Hyrbid?

asked by: TJ

0

Expert Reply:

The correct Draw-Tite Max-Frame Trailer Hitch Receiver for a 2021 Honda CR-V Hyrbid is part # DT79MR. It will not be compatible with the factory hands free liftgate feature but you can retain this using a relocation bracket which can be obtained through Honda. The Draw-Tite hitch offers a bolt-on install with no cutting or drilling required. It has a 2" opening that will be great for towing and hauling.

expert reply by: Conner L

0

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver item #DT79MR and the etrailer Trailer Hitch Receiver item #e98848 are nearly identical hitches. They both have a 3,500 lbs maximum towing capacity and a 525 lbs tongue weight limit. The main difference…

view full answer...

Answer 2

Yes, the EcoHitch #306-X7345 isn't the only trailer hitch designed to fit your 2022 Honda CR-V. The Draw-Tite you're asking about is found here on our site: - Draw-Tite Max-Frame Trailer Hitch Receiver #DT79MR I'm attaching the…

view full answer...

Answer 3

If you were to install both the Draw-Tite Max-Frame Trailer Hitch Receiver #DT79MR (76342) and #76128 on your 2022 Honda CR-V you'd find that the DT79MR is going to sit about 1/2" higher so these are relatively at the same height. With that…

view full answer...

Answer 4

The reason the Curt Trailer Hitch Receiver #C13397 for your 2019 Honda CR-V requires you to use the lift gate sensor relocation bracket and the Draw-Tite #DT79MR does not is due to the crosstube to sitting lower which allows you to move the antenna…

view full answer...

Answer 5

When installing the Draw Tite hitch part #DT79MR there is trimming required of the rear fascia to allow the hitch opening to pass through. If you watch the install video I attached you can see the trimming outlined.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Hey Erica, thanks for reaching out! Since your 2026 Honda CR-V is a Hybrid we're a bit limited on the hitch options, and you'll need to get one that does require some fascia cutting. For this, I recommend the etrailer Trailer Hitch Receiver…

view full answer...

Will Draw-Tite Trailer Hitch Fit a 2022 Honda CR-V Hyrbid

Continue Researching