Trailer Jack Cap that Fits Haul-Master 1000

Question

Question:

I need a dust cap for a Haul-Master 1000 lb. side screw jack model 41005. Looks like 1 3/4 inside. Do you have

asked by: Kevin S

0

Expert Reply:

The cap # MJ-1000B-CP is designed to fit MJ-1000B series jacks like # MJ-1206B which has inner tube diameter of 1-3/4 inches. This most likely would work for you.

expert reply by: Jameson C

0

Answer 1

Sure we have plenty of replacement caps for RAM jacks, however I would need a bit more information to get you the right cap. For instance, if you had a TJA-2000S series jack then you could use the Replacement Cap for etrailer and Ram Sidewind A-Frame…

view full answer...

Answer 2

Although I'm not sure what jack you have, we do have a handful of replacement caps for Ram jacks. Ram Square, Direct Weld, Sidewind Jack 10K - #TJD-12000-CP Ram Sidewind 2,000 lbs A-Frame Jacks - #TJA-2000S-CP Ram Swivel Marine MJ-1500B Series…

view full answer...

Answer 3

The Replacement Lippert Leveling Control Brain #LC53ED is the replacement for the 10540 controller. If you are needing the Control Panel #LC175225 we also have that available. The Harness #LC178278 is needed to convert the 4-pin square connector on…

view full answer...

Answer 4

We do have what you need available. I was able to locate the LC175226 controller but it is no longer available. I contacted the manufacturer and they provided information for the correct replacement part. The correct replacement part is the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Trailer Jack Cap that Fits Haul-Master 1000

Products Featured in This Question

Continue Researching