Matching Male and Female Weld-On Pipe Mounts for Trailer Swivel Jacks
Updated 03/02/2012 | Published 02/29/2012
Products Featured in This Question
Question:
Do you have a female tube to go with the maleBDPQM1900 that goes on the trailer? I need to weld a tube on my existing crank up jacks, as I cut them off and want to make swivel jacks out of them.
asked by: Richard S
Expert Reply:
The only square pipe mount we have is # BDPQM1900. It would be for if you already had jacks with the appropriate size female end (2-1/4 inch). What you can do is use round pipe mounts. You can use male end # BD015279, and female end # BD005024. Both of these pipe mounts use 5/8 inch diameter pins and the fit will be a little loose.
Another option is to use # BD015273 with # BD015271. These will be a tighter fit but use 9/16 inch diameter pins.
Product Page this Question was Asked From
Bulldog Replacement Pipe Mount for Swivel Jacks - 2-1/4" Male - Weld On - 5/8" Pull Pin
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Pipe Mounts
- 2-1/8 Inch Pipe Mount
- Bulldog
more information >
Continue Researching
- Shop: Bulldog Replacement Pipe Mount for Swivel Jacks - 2-1/2" Female - Weld On - 5/8" Pull Pin
- Search Results: trailer breakaway cable
- Video: All You Need to Know About the Bulldog Replacement Pipe Mount for Swivel Jacks
- Shop: Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 5/8" Pin Hole
- Video: What to Know About the Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks
- Shop: Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 3/4" Pin Hole
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Q&A: Dimensions of the Pro Series Round Pipe Mount Swivel Jack with Footplate
- Q&A: Total Length of a Pro Series Round, Pipe-Mount Swivel Jack # PS1401080303
- Q&A: Pull Pin Diameter for Round, Pipe Mount Swivel Jack TJP-2002S-B
- Shop: Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks - 5/8" Diameter
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 14-7/8" Travel - 2K
- Video: In-Depth Review of the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate
- Video: Review of the Round, Pipe Mount Swivel Jack w/ Footplate
- Shop: Bulldog Replacement Pipe Mount for Swivel Jacks - 1-7/8" Male - Weld On - 9/16" Pull Pin
- Article: Trailer Jacks
- Video: Review of the Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks
- Video: Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks Spec Review
- Search Results: bulldog 150 series
- Q&A: Replacement For Hub & Drum 8-207
- Q&A: Can I Get Key 0370 For The Master Lock Coupler Lock ML377KA
- Q&A: How Long Does It Take to Install B&W Turnoverball Underbed Gooseneck Trailer Hitch BWGNRK1020
- Q&A: Wiring a 7-Way RV Connector on a 1989 Ford F-250 Truck for Towing a Trailer with Electric Brakes
- Article: Where to Position the Trailer Axle?
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Adding Electric Over Hydraulic Disc Brakes
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Article: Determining Trailer Tongue Weight
- Article: How to Wire an Electric Winch
on Accessories and Parts
