Recommended Wiring Adapter for 2018 Toyota Tundra SR and Tekonsha Prodigy P3 Brake Controller

Question

Question:

We purchased a 2018 Toyota Tundra SR and it has the 7-pin connector on the bumper and from what Toyota Customer Service said, the plug for the brake controller is to the right of the steering wheel. I found the plug, but I can not find an adapter to connect my P3 brake controller to the service connection on the truck. Please help...

asked by: MATTHEW L

0

Expert Reply:

At this time, Tekonsha doesn't have a custom brake controller wiring harness, but Curt does. I recommend making an adapter compatible with your truck using the Curt Custom Wiring Adapter # C51455 and the Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers - 34" Long # 7894. This will give your the easy connection to your truck and your Prodigy P3 Brake Controller # 90195.

expert reply by: Jason S

0

Answer 1

On your 2015 Tundra, the vehicle side connector is located behind an access panel located in the center of the dash, just to the right of the steering column. You can check out the attached photo that shows where this panel is located. Using a trim…

view full answer...

Answer 2

For starters, you are going to want to remove the three button panel to the right of the steering wheel and look for a white rectangular connector with four pins. If present this is present then we do have a plug-in option available for you in the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Joe. To connect the Parkit360 Force Electric Trailer Dolly item #PA46VR to your trailer's battery, you'll need the Bulldog Winch Front Wiring Kit item #BDW20025. The Bulldog Winch Front Wiring Kit item #BDW20025 has the same style…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hi Grant, Thanks for the photo—and that's a nice boat! Based on what you've described, I do think adding a weight distribution system would be a great upgrade to your towing setup, especially for longer trips where you'll also be carrying…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Recommended Wiring Adapter for 2018 Toyota Tundra SR and Tekonsha Prodigy P3 Brake Controller

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching