How Does Brake Controller Install in 2010 GMC Sierra

Question

Question:

Do you have a Tekonsha wire adapter for 2010 GMC Sierra, or does this vehicle require a manual splice into the existing harness?

asked by: Duane S

0

Expert Reply:

On your 2010 GMC Sierra no plug is present under the dash for installing a brake controller, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash. I attached a help article and install video that covers this for you to check out as well.

For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well.

expert reply by: Jameson C

0

Answer 1

A 2010 GMC Sierra 1500 comes with the wiring for a 7-way even if it doesn't come with all the components. If you need a 7-way trailer connector, I recommend the Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles - Vehicle End…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 11

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire…

view full answer...

Answer 12

Hey Andrew. The Redarc Tow-Pro link will indeed work just fine for your 2026 Toyota BZ, and due to it not needing a brake output wire you do not need to hook up the brake out put wire at all. You'll plug the USCAR pig tail #20147 into the Tow-Pro…

view full answer...

How Does Brake Controller Install in 2010 GMC Sierra

Featured Help Information

Miscellaneous Media

Continue Researching