Recommendation for a Pipe Mounted Swivel Trailer Jack for a Home Made Trailer
Updated 05/27/2011 | Published 05/26/2011
Products Featured in This Question
Question:
I have a home built trailer with a pipe welded onto the frame. Id like to use the existing pipe mount for a trailer jack. Its an I-beam frame so a clamp-on trailer jack is not a good option. The pipe mount is a 2 OD horizontal stub welded onto the I-beam frame, about 12 bottom of pipe above the ground when the trailer is hooked up. Theres 10 between the back end of the pipe and the trailer frame. there are four 9/16 holes drilled into the pipe for a locking pin. Id like to buy a swivel jack that fits this existing mount without having to cut off the welded pipe and weld a new one on. Any suggestionsthe trailer weighs 1,000 pounds empty.
asked by: Robert S
Expert Reply:
I believe I have just the jack for you. Take a look at Pro Series Round, Pipe-Mount Swivel Jack, # PS1401460303. I went out to the warehouse and measured this jack and it will fit around a 2 inch diameter tube and uses a 9/16 inch pin. It is a short jack at 11-1/4 inches retracted. It has more than enough capacity at 5,000 pounds for your trailer. I looked at a lot of jacks while I was out there and this one seems to be the best fit.
Product Page this Question was Asked From
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 2,000 lbs
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Standard Grade
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Search Results: ram trailer jack
- Shop: Rack'Em Trailer Dolly
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Topwind - 10" Lift - 5,000 lbs
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-3/4" Travel - 2K
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 15-1/2" Travel - 3K
- Video: Complete Breakdown of the Ark Xtreme Off-Road Swivel Trailer Jack w/ 2 Wheels
- Video: An In-Depth Look at the Ark Xtreme Off-Road Swivel Trailer Jack w/ 2 Wheels
- Q&A: Replacement Pipe Mount Recommendation for Round, Pipe Mount Swivel Jack # TJP-2001-B
- Q&A: Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303
- Q&A: What is Diameter Of Mounting Pipe on Pro Series Round Pipe-Mount Swivel Jack # PS1401460303
- Search Results: curt trailer hitch ball
- Search Results: trailer dolly
- Search Results: trailer jack
- Search Results: trailer jack swivel
- Search Results: pipe mount swivel jack
- Search Results: pipe mount trailer jack with wheel
- Shop: Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Shop: Ark Xtreme Off-Road Swivel Trailer Jack w/ 2 Wheels - Sidewind - 18" Lift - Black - 1,650 lbs
- Shop: Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate - Sidewind - Side Mount - 1.8K
- Q&A: Can Storage Boxes be Mounted on Front of V-Nose Trailer
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Video: etrailer Electric Trailer Jack with 7-Way Feature Review
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: A Closer Look at the Stabilizer Jack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Demco Explains the EZ Latch: The Coupler That Latches Itself
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
on Trailer Jack
