Where is Brake Controller Install Port on a 2016 Nissan Titan XD

Question

Question:

I have a 2016 Nissian Titan XD that I bought a class 5 rcv and some Curt brake control stuff. Im having trouble finding the connector. Any ideas?

asked by: Mark B

0

Expert Reply:

I have attached a brake controller installation video on a Nissan Titan for you to check out. It shows exactly where the brake controller harness will be located under the dash. The truck in the video is a 2008 model, but it will be the same for your 2016 model. I have also attached a photo of the under side of the dash that shows where the harness will be located. The harness will be located underneath and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 6-pin connector that mates with the one on the adapter.

expert reply by: Jameson C

0

click to enlarge

Answer 1

To install the Draw-Tite Activator Trailer Brake Controller #5504 that you referenced to your 2017 Nissan Titan, all you will need is the Plug-In Wiring Adapter #3050-P if the truck is equipped with the factory 7-Way. One end of the harness will plug…

view full answer...

Answer 2

The wiring colors and functions on both actuators are pretty standard so the wiring information for the HydraStar Electric-Hydraulic Actuator for Disc Brakes, #HBA16, will be the same as that for the Dexter Electric Over Hydraulic Brake Actuator,…

view full answer...

Answer 3

Manufacturers can use any colors they want since there isn't really a standard for wire color and function. You will need to test each of the wires using a circuit tester such as #PTW2993 to determine the functions. Then you can attach them to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…

view full answer...

Where is Brake Controller Install Port on a 2016 Nissan Titan XD

Featured Help Information

Miscellaneous Media

Continue Researching