What are Drum and Shaft Dimensions of Fulton Single Speed Winch?

Question

Question:

I am looking at Fulton Winch # F142104 but I need to know some dimensions on the big drum and the shaft where the wire goes.

asked by: Jonathon

0

Expert Reply:

I headed out to the warehouse and took some measurements for the Fulton Single Speed Winch - 8" Long Handle - 1,300 lbs, # F142104. The drum has a diameter of approximately 5-1/2 inches, and the shaft has a length of about two inches. It can carry 30 feet of 5/16-inch rope, or 20 feet of 2-inch strap.

expert reply by: Kyle S

0

Answer 1

The mounting plate on the Fulton Single Speed Trailer Winch #F142201 is 5-3/8" long and 3-9/16" wide. The total height of the unit is 6-1/8" tall. I've also linked our review video for this winch that gives the overall dimensions…

view full answer...

Answer 2

Due to the age of your Fulton T1401 winch we don't have a repair kit available for it. It has been discontinued so as a replacement I recommend the Fulton Single Speed Trailer Winch - 8" Long Handle - 1,500 lbs #F142201. The slightly smaller…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

What are Drum and Shaft Dimensions of Fulton Single Speed Winch?

Continue Researching