Product Dimensions and Mounting Dimensions of Hopkins Graduated RV Levels
Updated 04/28/2016 | Published 04/25/2016
Question:
Hello! I am a designer at Felling Trailers in Sauk Centre, MN. We are going to be using your Hopkins trailer level #HM08525 on some of our trailers. I was wondering if you had any more details on this product, particularly material specs and more dimensions. I would like to provide mounting holes on my drawings, but am unable so far to find the hole location dimensions. Any help will be much appreciated. Thanks and have a great day!
asked by: Shannon B
Helpful Expert Reply:
I went out to the warehouse to take some measurements of the Hopkins Graduated RV Levels, Stick-On # HM08525 for you.
I found the level to measure approximately 3-3/4 inches long x 1-1/2 inches wide. Without the height of the logo, the level is 1-3/8 inches wide. Where the level is skinnier, it is approximately 1/8 of an inch thick. With the thickness of the level, it is approximately 1/2 inch thick.
The mounting holes are 2-3/4 inches apart on center. I confirmed with my contact at Hopkins that the hole bore diameter is 5/16 inches.
My contact at Hopkins also confirmed that the level is made from a resin plastic.
I've attached a photo with the measurements of the Hopkins Graduated RV Levels for you, as well as a review video of the levels.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: angled plunger trailer door holders
- Search Results: 2 5 16 hitch ball cover
- Search Results: hitch ball cover 2 5 16
- Search Results: trailer hitch ball cover
- Search Results: soccer ball hitch covers
- Search Results: 2~5/16 hitch ball gooseneck hitch
- Search Results: rv levels
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 15-1/2" Lift - 2,000 lbs
- Shop: Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket
- Shop: Hopkins Level+Plus Trailer Level with Memory
- Shop: Phoenix Electric Trailer Jack with Remote - A-Frame - 26" Lift - 5,500 lbs
- Shop: Ultra-Fab Protective Cover for Electric A-Frame Jacks - Vinyl - 10-1/2" x 13-3/4"
- Shop: Footplate for 2,000-lb and 5,000-lb Round, A-Frame Jacks
- Shop: Stackers Leveling Blocks w/ Bag for Trailers and RVs - 8-1/8" x 8-1/8" - Qty 10
- Video: A Closer Look at the Ultra-Fab Protective Cover for Electric A-Frame Jacks
- Video: Feature Review Ultra-Fab Protective Cover for Electric A-Frame Jacks
- Video: Checking Out the Stromberg Carlson Electric Trailer Jack
- Video: Phoenix Electric Trailer Jack with Remote Review
- Video: Wheel Masters Level Master Trailer Bubble Level Review
- Q&A: Will Wireless Trailer Jacks Remotes Interfere with Each Other
- Q&A: A-Frame Trailer Jacks that Have Highest Lift Ability
- Q&A: Troubleshooting the 5,500 lbs. Ultra-Fab Phoenix Electric Tongue Jack That Won't Retract
- Q&A: Are Remote Controls Paired to Individual Phoenix Electric Trailer Jack
- Q&A: Replacement Manual Override Cap For A Stromberg Carlson Electric Trailer Jack
- Q&A: Can Two 6 Volt Trailer Batteries Power the Stromberg Carlson Electric Jack
- Q&A: Replacement Manual Crank For Stromberg Carlson Electric Trailer Jack JET-5000
- Shop: Trailer Hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
on RV Levels
