Replacement Snap-Up Lever Tool for Fastway e2 Weight Distribution System FA94-00-1061

Question

Question:

lost my tool for putting bars up have e-2 hitch 10000 #98001000

asked by: Walter B

0

Expert Reply:

You can use Replacement Snap-Up Lever # FA92-00-6000 for your Fastway e2 Weight Distribution System # FA94-00-1061. For reference I also linked our page for all replacement parts for their weight distribution systems.

expert reply by: Adam R

0

Answer 1

The Replacement Snap-Up Lever for Equal-i-zer Weight Distribution Systems #EQ95-01-6050 comes in two halves that thread together. The lower half is 11-1/8 inches and the upper half is 11-1/4 inches. The total length of the lever is 22-3/8 inches.

view full answer...

Answer 2

We have the exact part number you mentioned. The snap-up lever part #FA92-00-6000 is exactly what you are looking for. We put the FA at the beginning of the part number to organize it with the manufacturer Fastway in our systems.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Snap-Up Lever Tool for Fastway e2 Weight Distribution System FA94-00-1061

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching