Can Prodigy RF Brake Controller Be Paired Without A Trailer Connected

Question

Question:

Is it possible to pair the remote and the brain together using a vehicle but without a trailer connected to the brain?

asked by: Yanni

0

Expert Reply:

You can start the pairing process for the # TK94FR with the trailer disconnected, but it will need to be connected to finish the pairing.

This is the procedure you need to follow to complete the pairing.
Connect the RF unit to the tow vehicle, but do not plug the trailer into the RF unit. Then, plug the hand held remote into the 12 volt power port (cigarette lighter). Next, turn the gain to minimum by rolling the power wheel towards the cord of the hand held. The display may show just a flashing NC-not the 0.0 mentioned in the instructions. Then, press and hold both the boost and manual buttons at the same time. The display will start counting down from P5 to PA. When the display shows PA, release both buttons and apply the brake pedal within ONE second. The display should change to a flashing 0.0. The control is now paired.

Once paired, you can plug the trailer into the RF box, and you will be good to go. If you still have trouble pairing with your X3 you can try taping off the pin in the 5 oclock position at the back of the RF (where the trailer plugs into) using electrical tape. Then go through the installation process.

expert reply by: Jeffrey L

0

Answer 1

I was able to determine that your trailer has torsion axles but not the brand or capacity. We know that Lance likes to use Dexter axles so I would be shocked if it wasn't a Dexter Torflex which the lift kit part #K71-707-02 you referenced would…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can Prodigy RF Brake Controller Be Paired Without A Trailer Connected

Continue Researching