You found the right spot and need your boat to stay put. This pre-rigged nylon anchor line clips on fast, resists UV damage, and gives you 100' of strong, flexible rope that won't twist up when the day winds down.
Tangled ropes and cords used to slow things down. With these sturdy wraps, your gear stays organized and easy to grab, so you can get started right away and keep your space clear from the start to the end of every trip.
Skip the soaked sleeves and sore back. This compact system floats your anchor to the surface so you don't have to haul it up by hand. You don't need to run wires or use a winch. All you need is physics and a little forward motion.
You found the right spot and need your boat to stay put. This pre-rigged nylon anchor line clips on fast, resists UV damage, and gives you 150' of strong, flexible rope that won't twist up when the day winds down.
If you're rafting up with friends, tying off at the dock, or dropping a small boat anchor, this floating rope clips on fast, resists twisting, and gives you 100' of hollow-braid strength for weekend boat days.
Docking usually happens when you're tired, ready to relax, or focused on tying up safely, not tying tricky knots. Tie your fender line once, snap it into this flush-mount plate, and you're done.
You found the right spot and need your boat to stay put. This pre-rigged, floating anchor line clips on fast, resists twisting, and gives you 50' of solid braid thats easy to coil and tough enough for the weekend grind.
Loose batteries cause wiring problems and shorts in your boat or RV. This tray fits 27 or 27M series batteries and keeps them secure, so you do not have to worry about bouncing batteries or losing power on the water or on the road.
Ever watched your boat drift while you're trying to relax or cast a line? This chain adds just enough weight to help your anchor bite fast and stay put so your boat holds steady while you focus on the water.
Quit wrestling with nets, straps, tarps, or that rogue bungee cord that's out to ruin your day. The HotMesh works with all kinds of cargo and even folds into its own storage bag. No more tangles or missing pieces - just buckle, cinch, and go.
Replaces the 2-5/16" and 2" combo hitch ball for your Andersen EZ heavy-duty adjustable ball mount or weight distribution system. Includes combo ball and 2 pins and clips.
This tire change kit makes swapping out a flat on your multi-axle trailer a total breeze. Just drive the good tire up onto the leveler to raise the adjacent tire up to 4" off the ground. You will be back on the road in no time.
Need more slack in your Andersen weight-distribution tension chains? Add up to 11-1/4" instantly with these extensions6 links plus a threaded coupler per side. Remove any links you dont need for a custom fit and smoother hitch setup.
You're lining up the fifth wheel, solo in the driveway, no spotter this time. With one try, it clicks into place. You step out, check the connection, and smile. That funnel did exactly what it promised.
Replace a damaged or worn spring bar on your Curt TruTrack 2P system with this forged steel bar. Designed for 5,000-lb to 8,000-lb setups only (17599). Restores sway control and load leveling for safer, more stable towing.
Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your controller and then plug the other end into the built-in port beneath your vehicle's dash.
Your trailer's wired right, but the brakes still won't fire. If your factory controller doesn't recognize your electric-over-hydraulic actuator, this adapter sends the signal it needs so the brakes activate, no rewiring required.
Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.
You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.
You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.
Reduce your Coleman-Mach RV air conditioner's start-up power demand by up to 75% and ease the strain on your AC compressor. Start and run your AC smoothly without tripping breakers or overloading your generator.
You're replacing your RV's AC and need a ceiling assembly that puts you in control. This non-ducted air distribution box has built-in knobs, adjustable louvers, and a pop-out filter. Designed for Coleman-Mach systems. Other parts required.