Turn your Coleman-Mach underbunk AC unit into a true comfort system. This kit adds a thermostat, remote, ducting, vents, and hardware so you can control temps and route your airflow exactly where you need it.
You're replacing your RV's thermostat and need a digital controller that works with your Coleman-Mach single-zone system. This is the thermostat only, but you can pair it with a compatible rooftop AC and ceiling assembly to finish your setup.
Replace the worn or non-working switch panel on your Cummins Onan generator. This panel lets you start and stop your gas or LP generator from a central location and works with select HGJBB, KY, and HGJAx models.
You packed right, now seal the deal. This fitted cover wraps your etrailer cargo carrier in weather-resistant protection, keeping your gear clean, dry, and out of sight. Bungee cords aren't a solution, they're wind chimes for your cargo.
Flip your license plate up to access your hitch, then drop it back down for a legal ride. This bolt-on bracket installs with no drilling and uses rustproof materials to keep your plate secure, visible, and out of the way when you need it.
New adventures are exciting, but leaving your bike unattended isn't. These wheel locks secure your bikes to the rack, deterring thieves and giving you peace of mind. Your ride will stay safe while you take a break or gear up for the next journey.
If you leave everything on the trail and are completely gassed when you're done cycling, you're not gonna want to lift your bike onto a rack before heading home. The Crosstrack Ramp lets you to roll your ride into place and hit the road.
Replaces the end cap with reflector for Hollywood Racks RV Rider (HR1600 or HR1700) or Sport Rider (HR1400, HR1450, HR1450-E, HR1450-R, or HR1455-E) bike rack. Fits 2" square tubing.
Cyclings supposed to be about the ride, not fighting with knobs or hunting for tools. These toolless adjustment dials let you switch wheel sizes with a quick twist, so your bike fits snug and you're rolling in seconds.
Replaces the support bracket for your Hollywood Racks RV Rider (HR1600 or HR1700) or Sport Rider SE (HR1450E-Z or HR1455E-Z) bike rack. Does not include carriage bolts (sold separately).
Replace the missing or damaged ramp for your Hollywood Racks Destination E so you can roll your heavy e-bikes on and off with ease. This direct replacement ramp connects to the end of the tray, then removes for storage.
When you're hauling your prized bikes, staying visible matters. This LED bar lights up your brake signals, turn indicators, and flashers, so even if your ride runs past sunset, other drivers know exactly where you are and what you're doing.
Early starts, late returns - some adventures just don't stick to daylight hours. The Destination E LED Light Bar helps keep you visible when it counts, making sure other drivers see you, your vehicle, and the gear you're hauling.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
A standard hose isn't long enough to run a brake line from your actuator to your trailer axle. This 20' hose gives you the reach to make that connection without adding couplers or extensions.
This stainless steel acorn lug nut laughs in the face of rust. Perfect for saltwater use, it stays strong and rust-free. No chipping, no peeling, just a tough, reliable fit that shrugs off moisture, salt, and road grime for the long haul.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
Too long for a short hose, too tight for a 6-footer? This 3' line gives you the extra length to make the connection without looping or straining. It's perfect for offset runs, frame tabs, and foldaway hinge setups.