New Arrivals

Replaces the drive arm assembly for your Lippert Edge RV awning without LEDs. Includes both the drive head and the arm. Black color matches your existing awning.

• Accessories and Parts
• RV Awnings
• Arms
• Drive Arms
• Lippert

Replaces the mount for your Solera 3000 Series RV awning.

• Accessories and Parts
• RV Awnings
• Mounting Hardware
• Lippert

Replaces 1 3/8" x 1-11/32" pin needed for your Solera RV awning. Dacromet finish resists corrosion.

• Accessories and Parts
• RV Awnings
• Hardware
• Arms
• Pins
• Lippert

Replace a missing side plug on your Lippert Power Tongue Jack V2. Push-in rubber cover (1-3/8" OD) seals the jack-head opening to keep out water, dirt, and road grimerestoring full protection in seconds, no tools required.

• Accessories and Parts
• Trailer Jack
• Camper Jacks
• Caps
• Lippert

Electric ground supply and wiring harness connects to the controller, breaker, and battery of your Hall Effect leveling system.

• Accessories and Parts
• Camper Jacks
• Wiring Harness
• Lippert

A damaged harness can make your RV's leveling system unreliable. This 4-pin interface harness restores electrical connections, ensuring smooth jack operation. Designed for Lippert Level-Up systems, it's a easy fix to get you back to camping.

• Accessories and Parts
• Camper Jacks
• Trailer Jack
• Wiring Harness
• Lippert

Lost or bent your extension rods? This replacement set gets your white Solera slide-out awning working like new again so you can get back to smooth RV living.

• Accessories and Parts
• RV Awnings
• Extension Rod
• White
• Lippert

Replaces the control board for your Lippert OneControl electric Travel Trailer RV leveling system (672136).

• Accessories and Parts
• Camper Jacks
• Controllers
• Control Panel
• Lippert

Use this Grade 5 flange nut with Grade 5 bolts (sold separately) to mount your Lippert components on your RV. Secures your steel or aluminum, manual pull-out Tread Lite steps or Ground Control 3.0 front jacks. Zinc plated to resist corrosion.

• Accessories and Parts
• Camper Jacks
• Hardware
• Nuts
• Lippert

This is the most convenient way to add LEDs to your RV awning: the light is pre-installed in a plastic strip and mounts to the wall. It's designed to get max brightness with minimal power, reflecting off the RV wall to fill the patio with light.

• Accessories and Parts
• RV Awnings
• Lights
• 16 Feet Long
• Strip Light
• Black
• Lippert

Replaces the motor assembly on your Lippert Coach RV steps.

• Accessories and Parts
• RV Steps
• Motors
• Lippert

For heavy-duty applications that require cable, this steel winch cable has a break strength of 4,200 lbs and a working load limit of 1,400 lbs.

• Accessories and Parts
• Electric Winch
• Trailer Winch
• Cables and Straps
• 3/16 Inch Diameter
• 4200 lbs
• Wire Rope
• CURT

Replace a lost or damaged bracket or install one in a second vehicle to easily transfer your Curt NEXT brake controller. The low-profile design installs above or below the dash and includes multiple mounting options for a secure, unobtrusive fit.

• Accessories and Parts
• Trailer Brake Controller
• Mounting Hardware
• Brackets
• CURT

For heavy-duty applications that require cable, this steel winch cable has a break strength of 5,600 lbs and a working load limit of 1,865 lbs.

• Accessories and Parts
• Electric Winch
• Trailer Winch
• Cables and Straps
• 7/32 Inch Diameter
• 5600 lbs
• Wire Rope
• CURT

Replace 2 worn or damaged backing plates on your single-axle trailer fender. Backing easily blocks water and road debris from hitting the side of your trailer.

• Accessories and Parts
• Trailer Fenders
• Fender Back
• CE Smith

Coupler repair kit contains all needed replacement parts for your CE Smith straight-tongue coupler with a 3,500-lb or 5,000-lb capacity, except for the coupler housing.

• Accessories and Parts
• Straight Tongue Trailer Coupler
• Coupler Repair
• CE Smith

Rustproof, durable aluminum bracket lets you mount a tail light to your trailer frame.

• Accessories and Parts
• Trailer Lights
• Mounting Hardware
• Brackets
• CE Smith

Replace the spindle nuts, washers, and cotter pins on your axle shaft with this kit from CE Smith.

• Accessories and Parts
• Trailer Suspension Parts
• Trailer Axles
• Hardware
• Nuts
• CE Smith

These brackets let you mount your single-axle fenders with side steps to your trailer. Includes 2 bolt-on, galvanized brackets to mount one fender. Works with CE19502, CE19503, CE19504 fenders (sold separately).

• Accessories and Parts
• Trailer Fenders
• Mounting Hardware
• Brackets
• CE Smith

Replaces the 90-degree post for your CE Smith post-style boat trailer guide-ons (27635, 27637, or 27638).

• Accessories and Parts
• Boat Trailer Parts
• Guide-On Parts
• Posts
• CE Smith

This towing safety flag is ideal for your kayak, SUP, or anything else you want to tow and draw attention to. Made of Oxford fabric and nylon webbing, so it holds up for the long haul.

• Accessories and Parts
• Trailers
• Watersport Carriers
• Sports Trailer Parts
• Watersport Trailer Parts
• Safety Flag
• CE Smith

Rustproof, durable aluminum bracket lets you mount a tail light to your trailer frame.

• Accessories and Parts
• Trailer Lights
• Mounting Hardware
• Brackets
• CE Smith

Rustproof, durable aluminum bracket lets you mount a tail light to your trailer frame.

• Accessories and Parts
• Trailer Lights
• Mounting Hardware
• Brackets
• CE Smith

This rust-resistant bracket lets you mount a bunk board vertically on your boat trailer. It's adjustable, so if you need to move your bunk up or down, just loosen the bolts a little and adjust as needed.

• Accessories and Parts
• Boat Trailer Parts
• Brackets
• Bunk Bracket
• CE Smith