These universal accessory bars let you carry more gear on your Adarac Aluminum or Pro Series ladder rack. Integrated channels in the top and bottom of the bars let you mount accessories that work with T-slots. Trim bars to fit as needed.
Equip your Adarac Aluminum Series ladder rack for your next overlanding adventure with these universal-fit side rails. T-slots on either side of the rails hold traction boards, Jerrycans, and other channel-mount accessories. Trim rails to fit.
These universal accessory bars let you carry more gear on your Adarac Aluminum or Pro Series ladder rack. Integrated channels in the top and bottom of the bars let you mount accessories that work with T-slots. Trim bars to fit as needed.
These universal accessory bars let you carry more gear on your Adarac Aluminum or Pro Series ladder rack. Integrated channels in the top and bottom of the bars let you mount accessories that work with T-slots. Trim bars to fit as needed.
This SAE to alligator clamps cable connects your 12V battery to your SAE power cable. Works with any 12V accessory that has a SAE connector on its power cord.
You'll need this air distribution box if you're upgrading your RV's AC to a 2025 ducted or ductless system with the new R32 refrigerant. New ACs will not work with any systems from 2024 or earlier.
Replaces the heavy-duty L-pins and clips from your Curt TruTrack 2P trunnion weight distribution system with integrated active sway control (17355) or support brackets (17517, 17518, and 17519).
Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.
You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.
You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.
Reduce your Coleman-Mach RV air conditioner's start-up power demand by up to 75% and ease the strain on your AC compressor. Start and run your AC smoothly without tripping breakers or overloading your generator.
You're replacing your RV's AC and need a ceiling assembly that puts you in control. This non-ducted air distribution box has built-in knobs, adjustable louvers, and a pop-out filter. Designed for Coleman-Mach systems. Other parts required.
You're replacing your RV's thermostat and need a digital controller that works with your Coleman-Mach single-zone system. This is the thermostat only, but you can pair it with a compatible rooftop AC and ceiling assembly to finish your setup.
Replace the worn or non-working switch panel on your Cummins Onan generator. This panel lets you start and stop your gas or LP generator from a central location and works with select HGJBB, KY, and HGJAx models.
Replaces the electric steps, motor, and control unit for your Kwikee 47 Series RV step. Motor and control unit automatically extend and retract the steps when you open and close the door. Wiring pigtail hardwires to your RV's power.
This kit includes the hardware for your Solera 2000 Series or Edge awning. The needed awning roller tubes and fabrics are sold separately. The 58" long arms offer sliding adjustable pitch. The wire is located at the bottom.
All it takes is one worn brake to throw your trailer off. Replacing a single ABS brake assembly restores smoother stopping and steadier tracking, so you stay in control on steep grades, in crosswinds, and during sudden traffic stops.
Need an air distribution box for your ductless Furrion Chill Cube RV AC setup? This low-profile unit includes a remote control that can sense and adjust the temperature of the area in your RV that the remote is in.
Replaces the drive arm assembly for your Lippert Edge RV awning without LEDs. Includes both the drive head and the arm. Black color matches your existing awning.