2011 Nissan Sentra Trailer Hitch
2011 Nissan Sentra Trailer Wiring
2011 Nissan Sentra Brake Controller
2011 Nissan Sentra Base Plate for Tow Bar
2011 Nissan Sentra Vehicle Tow Bar Brake System
2011 Nissan Sentra Vehicle Tow Bar Wiring
2011 Nissan Sentra Roof Rack
2011 Nissan Sentra Trunk Bike Rack
2011 Nissan Sentra Air Filter
2011 Nissan Sentra Performance Chip
2011 Nissan Sentra Interior Lights
2011 Nissan Sentra Exterior Lights
2011 Nissan Sentra Tire Chains
2011 Nissan Sentra Floor Mats
2011 Nissan Sentra Vehicle Covers
2011 Nissan Sentra Side Window Vents
2011 Nissan Sentra Vehicle Seat Covers
2011 Nissan Sentra Windshield Wiper Blades
Popular Nissan Sentra Accessories
Thule Helium Hitch Bike Rack Review - 2011 Nissan Sentra
Today on this 2011 Nissan Sentra, we're going to test with the Thule Helium Bike Carrier for 1-1/4" and 2" Hitches, part number TH970XT. We've already removed the adapter necessary to fit our 1-1/4" hitch. Let's go ahead and install our bike rack. The hand wheel on the back of the shank will be used to tighten down the rack and pull out any other rattle between the rack and the hitch. Once it's tightened down, we can lock it in place with the key. Then we'll install our safety pin.
Trailer Wiring Harness Installation - 2011 Nissan Sentra
Today were working on a 2011 Nissan Sentra. Were going to install toe ready T1 connector part number 118470. Weve already removed the spare tire and spare tire tools and trunk contents. Our next step is to remove the rear threshold. Were going to take a screwdriver or trim tool and get underneath the plastic and slowly pry up to release the fasteners from the sheet metal. With the threshold removed, well go ahead and set it aside.With the rear threshold removed, we now need to remove the carpeting behind the tail light.
Trailer Hitch Installation - 2011 Nissan Sentra
Today on this 2011 Nissan Sentra we are going to install Draw-Tite Hitch part number 24794. This will also be comparable to Hidden Hitch part number 60871. For the installation of this hitch it will be necessary to remove the spare tire and tools which we have already done along with any contents in the trunk. Our first step will be to take our bolt leader and our block and bolt and put them in our forward fastener. We will go ahead and slide our block in first, and then our bolt, and then pull them into position. Im going to go ahead and leave my bolt leader on as it will assist me in installing the hitch without loosing my hardwear back up into the frame.
Thule Doubletrack Hitch Bike Rack Review - 2011 Nissan Sentra
Today on our 2011 Nissan Sentra, we are going to do a test fit of the Thule Doubletrack Platform style 2 bike carrier. Lets go ahead and mount our rack into our 1-1/4 hitch. This bike carrier also comes with an adapter sleeve that will allow you to put in a 2 hitch. Once you get the hole lined up, we will install our anit-rattle bolt. The bolt can be tightened down with the applied wrench that comes with the install kit, or a wrench. Alright with the anti-rattle bolt tightened down we can go ahead and install our lock.
SportRack EZ Hitch Bike Rack Review - 2011 Nissan Sentra
Today were looking at a Nissan Sentra, were going to do a test fit of the SportRack 2 bike easy hitch mount rack with the wheel based mounts for inch and and 2 hitches, part number a30901. Lets go ahead and install our rack. Were setup to use 1-1/4 hitch, but if we had a 2 hitch we could use our adapter sleeve. First we will go ahead and thread in our anti-rattle bolt, Im using a wrench to tighten down that anti-rattle bolt. Now with the anti-rattle bolt tightened down, we will install our safety pin. Now I will go ahead and give you a few measurements.
Rhode Gear Highway Hitch Bike Rack Review - 2011 Nissan Sentra
:56 Today we are looking at a 2011 Nissan Sentra. Were going to do a test fit of the RoadGear 2 bike carrier for 1-1/4 hitch. First Im going to remove the 2 adapter so that our rack will fit our 1-1/4 hitch. Next will install our anti-rattle bolt and our safety pin. Our RoadGear rack will come with a tightening tool, but a wrench will work as well. Now that our rack is mounted in the hitch we will give you a couple of measurements.
Subscribe to email newsletter
privacy - we don't send unsolicited email
All images, layout and content copyright etrailer.com