view cartView Cart

Free Shipping on Orders Over $50

Only 5 Hours 29 Minutes Remaining


2010 Chevrolet Traverse Accessories

change vehicle




2010 Chevrolet Traverse Videos

U-Ace 3D Kagu Front Floor Liners Review - 2010 Chevrolet Traverse

Today on our 2010 Chevrolet Traverse. We'll be installing the U Ace 3D Kagu custom auto floor liner, with MAXpider grip, part number L1BC00811509. Now to begin our install, we'll first go ahead and remove all the manufacturers format, so we can install the new Kagu Liner. Now to remove the old one, we'll first unlock the hole down, pull it up, and remove it. We'll set aside, as it will not be reinstalled with the Kagu liner, because we'll only use one format at a time. Then as we slide the new liner in place, we'll line up with the hole down, then twist it back to lock it back in place, holding our floor liner in position. Additionally with the lock, it also has the MAXpider fibers that will really grip the carpeting to hold the floor liner in place, from shifting and moving around. Special contouring, it fits all the way around here at the threshold, over the driver's footrest.



3D Kagu Custom Cargo Area Floor Liner w/ MAXpider Grip Review - 2010 Chevrolet Traverse

Today on our 2010 Chevrolet Traverse, we'll be installing the U-Ace 3D Kagu Custom Cargo Area Floor Liner, part number M1CH0191309. This application is also available in gray, part number M1CH80531301, or tan, part number M1CH0531302. To begin our install, we'll first open up the rear hatch. Next we'll take the new cargo liner and set it in place. As you can see, the custom fit fits in nicely. It additionally has the MAXpider fibers that will help grip the carpeting to help hold the liner in place to keep it from moving or shifting around. It's got a raised outer edge all the way around to really help keep that dirt and debris contained in the liner and off the carpeting. The textured finish and a brick-style design will help keep your cargo from shifting or moving around. There you have it for the U-Ace 3D Kagu Custom Auto Floor Liner, part number M1CH0191309, black in color, for your 2010 Chevrolet Traverse. .



Husky Liners WeatherBeater Cargo Liner Review - 2010 Chevrolet Traverse

Today, on our 2010 Chevy Traverse, we'll be installing the Husky Weather Beater Custom Cargo Floor Liner, black in color, part number HL22021. Now, to begin our install, we'll simply open up the rear cargo door, and then put our Husky Liner in place. As you can see, our Husky Liner is designed to work with the third row seating down, for extended cargo coverage. We've got raised outer edges, and special molding to go around the seat belt and post, offering maximum protection going all the from the second row seating to your threshold, keeping that dirt, dust, debris contained on the liner and off the carpeting. Along with the easy care by simply wiping it down with a clean cloth or a wet towel, or hosing it off, maintenance of the floor liner made simple. There you have it for the Husky Weather Beater Custom auto floor liner, part number HL22021, black in color. This application is also available in tan, part number HL21023, or gray, part number HL21022, for your 2010 Chevy Traverse. .



Husky Front Floor Liners Review - 2010 Chevrolet Traverse

Today on our 2010 Chevy Traverse, we'll be installing the Husky Classic Custom Auto Floor Liner, part number HL31011. Now, to begin our install, we're going to start here on the driver's side by removing the old or manufactured floor mat. To do that, we'll simply unlock the hold down. Pull up on the floor mat. We'll just go ahead and pull it out and set it aside, because it will not be reinstalled. These Husky Liners come with a set. One for the driver and one for the passenger's side.



Trailer Brake Controller Installation - 2010 Chevrolet Traverse

Today, on our 2010 Chevy Traverse, we'll be installing the Tekonsha Primus IQ trailer brake controller for 1 to 3 axles, part number TK90160. The additional items we'll be using to complete the brake package hookup will ring terminals, part number 44-5356A. We'll also be using a total of approximately 35 feet of the jacketed 2 wire, in 12 gauge. It's part number 12-2-1. We'll also be using 2 breakers on the installation. We'll be using 1 inline 20 amp breaker, which is part number 9506P, and one 40 amp inline circuit breaker, which is part number 9510. Now, because this vehicle has already had an ETBC 7 started on it, we're just going to need to do a little bit of clean up work. The purple wire will not be used, and we will just take that up out of the way, and we will take part of our duplex wire, which is a white and a black wire, and we will connect the black wire to the black wire here, using a butt connector. We will also go ahead and connect the white wire to the blue wire. Again, we'll go ahead and use a butt connector to make this connection. Now, once we have this connection made, we're going to go ahead and clean up the wiring back here by using some zip ties, and electrical tape. Now, we're going to need to go ahead and route the gray duplex wire to the front of the vehicle. You want to make sure you stay away from any moving parts, areas that are sharp, or may become hot. We're going to need to find a grommet or something to poke into the cab of the vehicle. Now, this grommet, when you go from the inside of the vehicle, is actually to the right side of the gas pedal. Now, when you push the white wire in through the grommet, we'll go ahead then and push the additional white and black wire, but we're going to leave it in the gray sheathing for now. Next, we'll need to fish a second duplex wire, along with the left over black wire from the original duplex wire, into the engine compartment under the hood. Underneath the pedals here, there's a kick panel, or a plastic covering, that will need to be removed. There are 3 push fasteners that will need to be removed in order for this panel to come down. A flat head screwdriver, or a trim panel removal tool, works great to get these out. The first duplex cable that we routed into the cab with the white wire will get wired to our brake controller. Now, for the red wire, we're going to use the factory tow section, and we'll find which wire is only hot when the brake pedal is pressed in. As you can see here, using our test light, we find that the white wire is essentially the brake switch wire.



Thule XB16 Snow Tire Chains Review - 2010 Chevrolet Traverse

Today on our 2010 Chevrolet Traverse, we'll be installing the Thule standard snow tire chains for SUVs. This is part number TH01571255, with tire size P245/70/R17. Now these chains have V-shaped links for excellent traction in snow and ice. Now to install the chain, we'll first lay the chain out on the ground and take out any tangles or knots within the chain. We'll then take the chain by the blue cable and slide it underneath the vehicle behind the tire. We can then grab the two ends of the blue cable and bring them up toward the 12 o'clock position on our tire.



Trailer Hitch Installation - 2010 Chevrolet Traverse - Curt

Today on our 2010 Chevy Traverse, we'll be installing a Curt hitch, part number 13424. this is what our hitch looks like installed on our vehicle. Now we'll give you a few measurements to help you choose some accessories, such as a ball mount, bicycle rack, or cargo carrier. From the top of the opening on the hitch to the ground is approximately 20". From the center of the hitch pin hole to the edge of the rear bumper is approximately 6". Now let's go ahead with the installation.



Husky Rear Floor Liner Review - 2010 Chevrolet Traverse

Today, well be using a 2010 Chevy Traverse to do a test fit of our Husk Liners Classic Auto Floor Liners for the second row in the black color, Part Number HL61021. This liner is also available in tan, Part Number HL61023; as well as gray, Part Number HL61022.Youll start by removing the original floor mats or any other aftermarket mats you may already have installed. If you have the factory floor mats, youll notice that there are three tabs that you will twist before removing the original floor mat. Now, were ready to install our Husky liner. As you all notice, the Husky liner covers the thresholds at the door as well as having nibs that help hold it to the carpet.The liners made of a thermal plastic material that will not crack or break. Theres also channels in the floor liner that allows dirt and debris to be channeled away from your feet.



Roadmaster Base Plate Installation - 2010 Chevrolet Traverse

Today on our 2010 Chevrolet Traverse, we will be installing the Roadmaster EZ base plate kit, part number 523149-1. Now to begin our installation we will need to remove the front bumper cover, to do this we will remove the ten plastic fasteners attaching the radiator cover to the course of port fascia here on the top. Now on each side of the vehicle theres one plastic fastener attaching the weather stripping here at the back for the hood, to the cover, so well need to remove those as well. With that done we can go ahead and set the cover aside for reinstallation later. We will now remove the six 7 mm bolts attaching the radiator core to the course of port; this will loosen up the upper bumper cover. We will now move into our fender wells here where we will need to remove the 7 mm bolt and the two Phillips head screws, these are all located on the inside edge of the fender well.



Roadmaster Tow Bar Wiring Kit Installation - 2010 Chevrolet Traverse

Today on our 2012 Chevrolet Traverse well be installing the Roadmaster Universal Hy-Power diode wiring kit, part number RM-154. To begin our install well remove the long four pole wiring from our packaging. Well then cut the packaging material from the wiring and then cut the end off of one side of our harness. With that done well need to route our wiring harness from the front of the vehicle to the drivers side tail light assembly. Well need to leave the four pole that we left attached to our harness here at the front of the vehicle. Well then route our four pole wiring harness back on the vehicle being careful to stay away from any moving components such as your vehicles suspension or hot components such as the vehicles exhaust.



Glacier Cable Snow Tire Chains Review - 2010 Chevrolet Traverse

Today on our 2010 Chevrolet Traverse, well be installing the glacier cable snow tire chains for light trucks, part number PW3010C. These tire chains are perfect for the occasional use and feature of rugged steel wire covered with case hard and steel rollers retraction. Theyre very easy to install and comply with all DOT specifications. Theyll fit either front or rear of the vehicle. Now today well be installing them on a tire sized 245/70 R17. Youll notice that the cable chains have a tag marking left-hand or right-hand side.



Trailer Wiring Harness Installation - 2010 Chevrolet Traverse

Today on this 2010 Chevrolet Traverse we are going to install part number 118450 from Tow Ready. This is their T-One wiring harness and the first steps involved is to open up the back hatch of the vehicle so we can get access to the tail lights themselves. To remove the tail lights we have got to remove these caps right here first off. There will be some bolts underneath to remove so we can take the tail light off. We will take out our screws and this is our connection behind the tail light. Push down on the little button and it should come right apart. 00:43



Trailer Hitch Installation - 2010 Chevrolet Traverse

Today on this 2010 Chevrolet Traverse we are going to install part number 75528 from Draw-Tite. This is also going to apply to Hidden Hitch part number 87435. Our next steps involved is to take this panel that is at the bottom of the bumper in the center and we are going to remove it. All you do is twist the two knobs to unlock it and you can pull it apart. The cover that was right here is going to have to stay off because it was not made for this hitch. Our next step is going to be lower the exhaust. We are going to spray down the rubber hangers with some lubricant and we are going to push them off to the side that way we can lower our exhaust. 00:34





2010 Chevrolet Traverse Questions and Answers


  • Recommendation of Trailer Hub and Drums and Axles
  • The trailer hub and drum assembly # 845476UC3 includes bearings and races from Redline. They are made in China. I would assume you have 5 on 4-3/4 inch bolt pattern but you will need to replace the spindle. Welding on a new spindle is a precision trade craft requiring a special jig installed by an experienced professional. Otherwise, you could continue having the same problem. Depending if you currently have a round or square will determine which spindle you need. If it's round, you...
    view full answer...

  • Folding Cargo Carrier for 2010 Chevy Traverse
  • Rola offers a folding carrier, part # 59550 that's compatible with the # 59516 light kit. To see if the basket would work on your vehicle, you'll need to measure the distance between the hitch pin hole in your receiver to the furthest rearward edge of the rear bumper, as shown in the FAQ article I've linked you to. As long as this distance is less than 7 inches, the carrier would be compatible with your vehicle. Unfortunately, Rola doesn't make a folding version of the # 59502. The Surco...
    view full answer...

  • Removing a Trailer Hitch Installed on a 2010 Chevrolet Traverse
  • Since your husband effectively installed Draw-Tite Hitch # 75528 on his 2010 Traverse using our videos, he should have no trouble removing it. We do not produce hitch removal videos (although with the proliferation of auto leases this need may be upon us!) since your husband did the install, which required "fighting gravity" to lift the hitch into place, the removal process will at least require a bit less elbow grease. I suggest he liberally apply a spray-on penetrating lubricant a...
    view full answer...

  • Can a 5th Airborne Air Ride Pin Box be Used with a 5th Wheel to Gooseneck Adapter
  • The 5th Airborne air ride pin boxes cannot be used with any 5th wheel to gooseneck adapters. But we may have a product that you can use that will provide you with the benefits of an air ride pin box but allow you to connect to a gooseneck trailer hitch. Take a look at the Reese Goose Box, # RP94622. This is an air ride pin box that installs on the trailer and couples to a gooseneck ball. This model will fit Lippert 0719, 1621 and 1621HD pin boxes and Fabex PB-600 series pin boxes. We...
    view full answer...

  • Are the Optional Car Clips Needed to Mount Rightline Saddlebag on a 2010 Chevy Traverse w/Roof Rack
  • That is correct you can attach the Rightline Saddlebag, # RL100B90 to side rails or crossbars and not have to use the optional clips, # RL100605. These clips would be needed if the vehicle did not have raised side rails or crossbars on the roof. We usually ship orders of items in stock on the same day depending on the time of day it is. I am certain that many places sell the same bag but why shop anywhere else when you have etrailer.com at your fingertips!
    view full answer...

  • Cargo Carrier with Bike Rack for Simultaneous Use on 2010 Chevrolet Traverse
  • It is almost a certainty that using two hitch-mount accessories at the same time on your 2010 Traverse will result in interference between the two carriers themselves and/or the bikes and cargo loaded on them. There are no cargo carriers that have a receiver tube on their back to allow for piggy-backing a second hitch-type accessory such as a bike rack. These do not exist because such an arrangement would place extreme stress on the hitch and vehicle frame and would be likely to damage...
    view full answer...

  • Installing Hopkins Agility Trailer Brake Controller # HM47294 in a 2010 Chevrolet Traverse
  • The Hopkins Agility Trailer Brake Controller # HM47294 that you referenced is a good cost-effective proportional brake controller. There are comparable units from Tekonsha, the brand we most often recommend, that offer easier set-up and operation, such as the Prodigy P2 # 90885. However, for occasional use the Hopkins may suit your needs well enough. If your Traverse has the factory tow package (with a 7-way trailer connector installed at the rear bumper) then you can use a quick connect...
    view full answer...

  • Roof Rack Recommendation for a 2010 Chevrolet Traverse With the Rear Moon Roof
  • We have many roof rack options for your 2010 Chevrolet Traverse with the rear moon roof. I have attached a link to the compatible roof racks for you to check out. Of the available roof racks, I recommend looking at the Rhino-Rack RS 2500 Roof Rack, # RRRS538B. This roof rack mounts on the outside of the flush side rails on your vehicles roof and will not interfere with the moon roof. I would not recommend opening the moon roof with the roof rack installed because the mounting hardware...
    view full answer...

  • 2010 Chevy Traverse Hitch Recommendation that is Recessed and Allows Fascia Panel To Be Installed
  • After reviewing the installation instructions for the Draw-Tite, Hidden Hitch, and Curt, hitches that are listed as a compatible fit for your 2010 Chevrolet Traverse the Curt # 13424 does not extend past the rear edge of the vehicle. The distance from the center of the hitch pin location on the hitch to the rear edge of the bumper is 6 inches, this measurement is shown in the included video for your reference. Additionally the installation instructions state that the panel may be reinstalled...
    view full answer...

  • Will Thule Raceway 2 Trunk Carrier Fit Both 2010 Honda CRV and Also 2010 Chevrolet Traverse
  • The Thule Raceway 2 Trunk-Mount Bike Carrier, part # TH9001PRO, will fit on your 2010 Traverse but will not fit on your 2010 Honda CR-V. None of the Thule trunk-mount carriers will fit properly on your 2010 CR-V. Yakima offers many trunk carriers that will work on your CR-V but none of these will work on your Traverse! Hollywood Racks does offer their Over-the-Top 2-bike carrier, part # HRF2, that will work on both vehicles (as long as the CR-V does not have a trunk-mount spare tire)....
    view full answer...

  • Will the Yakima Megawarrior or the Thule MOAB Baskets with Extensions Fit on a 2010 Chevy Traverse
  • I spoke to my contacts at Thule and Yakima and found that the Yakima Megawarrior Cargo Basket with Extension, # Y07080-82, and the Thule M.O.A.B. Cargo Basket, # TH690, with Extension, # TH691XT, will fit on the factory roof rack of your 2010 Chevrolet Traverse. The Yakima MegaWarrior requires a crossbar spread of at least 36 inches when used with the extension and the Thule M.O.A.B requires a crossbar spread of at least 28 inches when used with the extension.
    view full answer...

  • Choosing the Correct Weight Distribution System for a Palomino Trek G145 with Tongue Weight 427 lbs
  • Typically weight distribution systems will accommodate a range of tongue weights. As long as the loaded tongue weight of your trailer falls within that range, then you should not have a problem using the system. I am not sure which system you have, but I would first verify with your dealer or with Pro Series what the tongue weight range is for your system. We carry a Pro Series Weight Distribution System, # PS49902, that has a tongue weight range of 550 lbs to 750 lbs. If this is the...
    view full answer...

  • Recommendation for Carrying 5 Bikes on a 2010 Chevrolet Traverse without a Trailer Hitch
  • The safest and easiest way to carry 5 bikes with your 2010 Chevrolet Traverse would be to add a trailer hitch and use a hitch mounted bike rack for 5 bikes. If you do not want to add a trailer hitch, then you will need to use a combination of a trunk mounted bike rack and roof mounted bike racks or store some bikes in the rear cargo area of your vehicle. Trunk mounted bike racks can only support up to 3 bikes. Our most popular trunk mounted bike rack is the Thule Raceway 3 Bike Rack,...
    view full answer...

  • Trailer Brake Controller Wiring Adapter for a 2010 Chevy Traverse and Tekonsha Prodigy Controller
  • The Tekonsha Wire Replacement, # 3026-P, is the correct wiring adapter for a 2010 Chevy Traverse with a factory installed 7-Way trailer connector. I have included a link to the installation instructions for the adapter for you. This harness is also compatible with the Tekonsha Prodigy Brake Controller, # 90185.
    view full answer...

  • Will Tow Ready T-One Vehicle Wiring Harness # 118450 Fit My 2010 Chevrolet Traverse w/ Tow Package
  • The item you selected, T-One Vehicle Wiring Harness with 4 Pole, part # 118450, will work on all models of the Chevrolet Traverse. The # 118450 harness plugs in-line with your tail light wiring connectors and is not connected to the fuse block. To install, you would just plug in-line with your tail light wiring harness and connect the ground wire to a clean metal surface on the vehicle frame. This harness will give you a 4-way connector at the rear of your vehicle. If you are needing...
    view full answer...

  • Tilting Trailer Hitch Mounted Bike Rack for a Class II Hitch on a 2004 Subaru Legacy Wagon
  • You are correct. The only available trailer hitches for your 2004 Subaru Legacy are class II, 1-1/4 inch trailer hitches. I do not advise modifying the hitch in anyway. Making modifications will void the warranty and make the capacity unknown. Adding on a 2 inch receiver would not change the hitches capacity and a class II trailer hitch cannot withstand the stresses that would be associated with the operation of the SwingDaddy. I would assume the reason you prefer the Yakima SwingDaddy,...
    view full answer...

  • Installing the Tekonsha Prodigy P2 Brake Controller from Scratch on a 2010 Chevy Traverse
  • Without a factory tow package, you will need to hardwire the Prodigy P2 brake controller, # 90885 (installation details linked below) for your 2010 Chevy Traverse. First, you will need to install Tow Ready Custom Fit Vehicle Wiring, # 118450. I have included a video installation on a similar vehicle. Next you will need to install a 7 and 4 Way Installation Kit, # ETBC7. Plug the 4-Way you previously installed into the back of the ETBC7. There will then be 4 wires left to connect:...
    view full answer...

  • Can the Fascia Door Be Replaced Over the Hitch Opening On a 2010 Chevy Traverse
  • If you are talking about the fascia door that is removed from the lower center of the bumper, the Draw-Tite, # 75528, and Hidden Hitch, # 87435, will not allow you to replace the fascia door as the receiver opening sticks out just a little too far. The Curt Trailer Hitch, # 13424, instructions, linked below, state that on some models, it is possible to replace the fascia door when the hitch is not being used. I spoke with my contact at Curt to clarify and she stated that on your Traverse...
    view full answer...

  • Trailer Hitch and Wiring Installation Difficulty and Details for a 2010 Chevy Traverse
  • We have a difficulty rating system based on how long it would take the average person to install a hitch. For the Draw-Tite Trailer Hitch, # 75528, and your 2010 Chevy Traverse, we rate the difficulty at a 3 out of 10 meaning it should take about 30 minutes. There is no drilling required. You will have to temporarily detach the rubber exhaust hangars to put the hitch in position. I can tell you that with the proper tools, and someone to help you lift and position the hitch, this is...
    view full answer...

  • What is the Distance Between the Holes on the Ball Mount Adjustable with Sway-Control Tab
  • The distance between the holes on the Ball Mount Adjustable with Sway-Control Tab, 6,000 lbs, # 7390, is 1-1/4 inches, center to center.
    view full answer...

  • What Hitch Cargo Carrier do You Recommend for a 2010 Chevrolet Traverse
  • I do like the MaxxTow Aluminum Cargo Carrier, part # MT70108 as an option if you were to add a lockable box on top of it. My wife and I used Tow Ready part # 63153 on a summer fishing trip to Canada, 16 hour drive each way. We had no complaints about with that carrier. Plenty of space for all our stuff and the rails provide good anchor points for straps. If your particular state requires lights, there is a pre-fit kit for the Tow Ready carrier, part # 20174. My next carrier will be...
    view full answer...

  • Installing an Electric Trailer Brake Controller on a 2010 Chevy Traverse with Tow Package
  • The connector you need for a 2010 Chevy Traverse with Towing package is part # 3026-P. I have added a link to it below. I am looking at the instructions and it appears you will need a small flat head screw driver to gently pry the plastic push-rivets out to release the panel. I have added a link to the instructions below so you can see where the connector is located.
    view full answer...










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com