view cartView Cart
Only 17 Hours 1 Minutes Remaining

2009 Dodge Ram Pickup Accessories

change vehicle

Popular Dodge Ram Pickup Accessories





2009 Dodge Ram Pickup Videos

Gooseneck Trailer Hitch Installation - 2009 Dodge Ram

All right, today in this 2009 Dodge Ram Pickup 2500 Series we're going to install part number C60660. This is the Curt EZr Double Lock Gooseneck Installation Kit. Let's take a quick look into the operation of the hitch. We pull it out and then twist it towards the front of the truck. You can see how it will lock into place. All right, now we know how the locking pins work, let's go ahead and install the ball.



Timbren Rear Suspension System Installation - 2009 Dodge Ram

All right, today, on a Dodge 2009 Ram Pickup, we're going to install part TDR2500ca from Timbren. First thing we need to do is get access to the jounce stop. This particular application replaces it. We'll use a hitch bolt in its place. What we're going to do is take our bracket that goes to the bottom of the frame and we're going to install a spacer, and then an additional spacer, which is sold separately. This additional part number will be A25723-90AH00.



Custer Surface Mount Back-up Alarm Installation - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram Pickup we'll be installing the Custer Electronics Surface Mount Back-up Alarm. Part number BK97DB. Our back-up alarm will mount on the passenger side, underneath the tail light assembly. To begin our install, we'll first go ahead and attach our power and ground wire to the back-up alarm up. To do this, we'll take a piece of wire, strip back both ends and end ring terminal to each side. This application, we use the white wires are ground and brown wire is our power. We'll go ahead and put it on the studs at the back-up alarm and then secure with a knot supply with the back-up alarm. Now with our wire secures to the back-up alarm, we'll go ahead and mount the back-up alarm underneath the pickup bed. Note we'll be using the self-tapping screws to secure the back-up alarm and we'll locate an area where the sheet metal doubles up for a more secure mounting location. Now with our alarm mounted, we'll go ahead and route the wire up behind the passenger side tail assembly following the manufacturer's wiring. Next, we'll go ahead and open the tail gate, remove the 2 fasteners and secure the tail light assembly and pop it free from its mounting location. Note, be careful not to break the alignment tabs underneath the tail light assembly. Next, we'll go ahead and pull the wiring through the excess hole and take the white wire and a ring terminal.



Roadmaster InvisiBrake Supplemental Braking System Installation - 2009 Dodge Ram Pickup

All right today on this 2009 Dodge Ram Pickup 1500 Series Quad Cab were going to install part number RM-8700. This is a Roadmaster Invisibrake Supplemental Braking System. All right, to start off our install were going to go ahead and remove the front seat. There are four bolts we have to remove, two in the front and two in the back. Once we have those removed we can go ahead and tilt the seat back then well disconnect the electrical connectors. Theres only one connector thats active and the other plug we just need to simply pry off and set off to the side. Then we can go ahead and pull out our seat.



AIRAID Premium Direct-Fit Replacement Filter Installation - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram Pickup 5.7 Liter, we'll be installing the Airaid Premium Direct Replacement Filter, part number AR850-447. We'll begin here by raising the hood of the vehicle and then undoing the four clips that hold the cover on the air box. With these four clips removed, we can go ahead and lift the air box cover up. We'll go ahead and remove the old filter and now we're ready to put the new Airaid filter in place. This new Airaid filter is washable as well as reusable. When the filter becomes dirty, simply blow it out with air or wash it out with a hose and let it air dry.



Blue Ox Base Plate Kit Installation - 2009 Dodge Ram Pickup

Today in this 2009 Dodge Ram pickup, we're going to install part number BX1986 from Blue Ox. First thing we need to do is go ahead and remove the front plastic insert. There will be six push pins that we have to pull out. You need a small screwdriver to get them started to pull out the centers then we can get the rest and remove it out. Then we'll go ahead and remove the insert. There's some tabs in the bottom that we have to pull up so we can get them to break free.



Softride Hang5 Hitch Bike Rack Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500 we'll be test fitting the Softride Hang5 Hitch Mounted 5 Bike Rack, Part Number SR26496. We'll begin our test fit by sliding in the shank of the mast into the opening of the hitch. After lining up our pin holes, we'll thread our anti-rattle bolt through the pin holes and then tighten it down using a wrench. We'll then go ahead and slide the arms of the bike rack into the upper portion of the mast. You'll know when the arms have been fully secured when you hear an audible click. We'll go ahead and go over a few clearance measurements to see how the two fit together.



Blue Ox Tail Light Wiring Kit Installation - 2009 Dodge Ram Pickup

All right, today on this 2009 Dodge Ram pick-up 1500 series quad cab, we're going to install part number BX8869. This is a Blue Ox taillight wiring kit bulb and socket. To start off our install, we're going to take our wire harness with the four wires and we're going to run it through the front of the truck going towards the back. Now our truck has a six volt connector that is previously installed on this truck. This was installed as a part as a base plate installation kit. So I'm going to go ahead and take it back apart and then go ahead and run our wiring through.





Longview Custom Towing Mirrors Installation - 2009 Dodge Ram Pickup

Today on our 2009 Dodge RAM pickup, we're doing a test fit of the Longview Custom Towing Mirrors slip-on style for the driver and the passenger side, part number LVT-3100C. Now, the Longview Custom Towing Mirrors do come in a right and left side. The mirror that's part of the towing mirror is fully adjustable, but you must do it manually. You can see here inside, there's a foam pad as well as a couple of felt areas that keep your factory mirror from being scratched. It is also made of a durable ABS plastic housing. As you can see here on the bottom, there's kind of a cutout area which allows you to still see the puddle light on the factory mirror. To install the mirror, you simply slide it over the factory mirror, then you use the hook and hook it to the edge of the factory mirror, and we found when putting the mirror on, it's best if you hold your hand on the hook and bend in just slightly on the towing mirror.



Hopkins Smart Hitch Backup Camera Installation - 2009 Dodge Ram Pickup

Today on this 2009 Dodge Ram Pickup we'll be installing the Hopkins Smart Hitch Backup Camera, part number HM50002. Other items that we'll be using during the installation include the Loctite RTV 598 High-Performance Silicone Gasket Maker, part number LT37467. To begin with, we'll need to remove the two screws that hold the rear license plate to the vehicle. Once we do that, we'll go ahead and take the bracket that has the camera as well as the two sensors, one on either side, and we'll put our license plate into the bracket. Then we'll use the two longer screws that come with the kit to reconnect our bracket and license plate to the rear of the vehicle. You'll also notice that there's a short lead that comes off the back of the camera. In this case, we'll feed it in between the rear bumper and the lower part of the bed. Once we have the license plate and the camera bracket back into place, now we can go up underneath the vehicle.



Husky Liners Classic Custom Rear Floor Liners Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram Pickup 1500 Series Quad Cab we'll be doing a test fit of the Husky Liner Classic Custom Auto Floor Liner for the rear or second row in the black color, part number HL60831. This liner is also available in the gray color, part number HL60832. As well as tan, which is part number HL60833. Before we begin, it's best to scoot both the driver and the passenger front seat all the way forward as this will make removing any existing floor liner or mat much easier. As well as installing your new Husky Liner. Next we'll go ahead and remove any existing floor liner or mat from the vehicle.



U-Ace 3D Kagu Custom Front Floor Liners Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram pickup 1500 series quad cab were doing a test fit of the U-Ace 3D Kagu custom auto floor liners with max spider grips for the front in the black color, part #: L1DG00411509. These mats are also available in tan, part #: L1DG00411502 as well as in the gray color, part #: L1DG00411501. Well begin here on the driver side. As youll the liner goes all the way up underneath the pedals as well as up the sides of the foot well area. Theres also a foot pad area built in as well as the liner being designed with three layers. The top layer being a durable thermoplastic rubber, the middle layer being waterproof and shock absorbent and the underside covered in the anti-slip max spider grips which hold your mat in place.



MaxxTow Tow Strap Loop Review - 2009 Dodge Ram Pickup

Today, on our 2009 Dodge Ram 1500, we'll be test-fitting the MaxxTow Tow Strap Loop, for 2-inch hitches, rated at 10,000 pounds, part number MT70029. This hitch-mounted heavy-duty shackle can be used as an attachment point for strap, cable or rope. We'll begin our test-fit by sliding the shank of it into the receiver tube of our hitch. We can then secure it with a pin and clip, which is sold separately. And that completes today's test-fit for the MaxxTow Tow Strap Loop, for 2-inch trailer hitches, rated at 10,000 pounds, part number MT70029, on our 2009 Dodge Ram 1500. .



Curt Tri-Ball Mount Review - 2009 Dodge Ram Pickup

Today on our Dodge Ram 2009 1500, we'll be test fitting the Curt tri-ball mount for 2 inchhitches, part number C45001. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary, due to tire size, hitch style, or aftermarketaccessories. We'll begin our test fit by sliding the shank of the ball mount into our opening of our receiver tube. We'll then secure it with a pin and clip.



Curt Multi-Ball Adjustable Ball Mount Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500 we'll be test fitting a Curt Multiball Adjustable Ball Mount for two inch hitches, part number d900. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. In the draw position, we'll begin out test fit by sliding the shank of the ball mount into the receiver tube of our hitch, we'll then secure it with a pin and clip. As you can see we can pull the pin at the base of the ball mount in order to access the three different size balls.





MaxxTow Ball Mount Review - 2009 Dodge Ram Pickup

Today, on our 2009 Dodge Ram 1500, we'll be test-fitting the MaxxTow Ball Mount, with 2-inch accessory receiver, for 2-inch hitches, with a two and a quarter inch drop, rated at 5,000 pounds, part number MT70066. We'll begin our test-fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now, the hitch height for this vehicle is twenty inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. With the accessory receiver in the upright position, we'll begin our test-fit by sliding it into the receiver tube of our hitch.



Hidden Hitch Ball Mount with 6 Inch Drop Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500 we'll be test fitting the Hidden Hitch Ball Mount with a 4 3/4 inch rise or 6 inch drop, rated at 6000 pounds, part number 80240. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now, the hitch height for this vehicle is 20 inches. keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll begin our test fit by sliding the shank of the ball mount into the opening of the hitch in the draw position and securing it with a pin and clip. We'll then measure from the ground to the top of the ball platform and we'll get a measurement of about 13 3/4 inches.



Draw-Tite Ball Mount Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram pickup well be test fitting the Draw Tite ball mount with a rise or 2 drop rated at 7500 pounds, part number 2923. Well begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now the hitch height for his vehicle is 20. Keep in mind that this measurement may vary due to tire size, hitch style or aftermarket accessories. Well now slide the shank of the ball mount in the drop position into the receiver tube of our hitch. Well then secure it with a pin and clip.



Diversi-Tech Adjustable Ball Mount Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500 we'll be test fitting the Diversi Tech Self Locking adjustable aluminum ball mount with a six in drop or seven inch rise rated at 10,000 pounds, part number dtalbm6600. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now, the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll begin our test fit in the drop position by sliding the shank of the ball mount into the receiver tube of our hitch. We'll then turn the key to allow the integrated hitch pin to slide into the hitch pin holes.



Convert-A-Ball Ball Mount with 8 Inch Drop Review - 2009 Dodge Ram Pickup

Today, on our 2009 Dodge Ram 1500, we'll be test-fitting the Convert-A-Ball Cushion Ball Mount for 2-inch hitches, part number AMSC8. We'll begin our test-fit by first obtaining the hitch height of our vehicle, the hitch height is the measurement from the ground to the inside top of the receiver tube. Now, the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after-market accessories. We'll begin our test-fit in the drop position by sliding the shank of the ball mount into the receiver tube of our hitch, we'll then secure it with the pin and clip. We'll now measure from the ground to the top of the ball platform and we'll get a measurement of about 12 inches. If your vehicle's hitch height matches the hitch height of our vehicle and trailer's ride height matches this measurement, this will be an appropriate ball mount for you.



Convert-A-Ball Ball Mount with 10 Inch Drop Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500, we'll be test fitting the Convert A Ball Cushion Ball Mount for two inch hitches with an 8 3/4 inch rise or 10 inch drop, rated at 10,000 pounds, part number amsc10. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll begin our test fit by sliding the shank of the ball mount in the drop position into the receiver tube of our hitch, we'll then secure it with pin and clip. We'll then measure from the ground to the top of the ball platform and we'll get a measurement of about 10 inches.



Convert-A-Ball Heavy Duty Ball Mount with 2 Inch Drop Review - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram 1500 we'll be test fitting the Covert-a-Ball Cushion Ball Mount for 2-inch hitches with a 1-inch rise or 2-inch drop rated at 14,000 pounds, part number AMSC2HD. We'll begin our test fit by first obtaining the hitch height of our vehicle. The hitch height is the measurement from the ground to the inside top of the receiver tube. Now the hitch height for this vehicle is 20 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll begin our test fit in the drop position by sliding the shank of the ball mount into the receiver tube of our hitch. We'll then secure it with the pin and clip. We'll now measure from the ground to the top of the ball platform, and we'll get get a measurement of about 17-3/4 inches.





AIRAID Premium Direct-Fit Air Filter Installation - 2009 Dodge Ram Pickup

Today on our 2009 Dodge Ram Pick-Up 1500 Series Quad Cab well be installing the Airaid Premium Direct Fit Replacement Filter part number AR851-447. To begin with well need to go ahead and raise the hood on the vehicle. On this particular vehicle the air box is located on the passengers side. There are four tabs that well need to open up in order to lift the cover off the air filter box. With these four tabs undone, we can go ahead and lift the air filter cover off. Youll just need to lift it up enough to pull the original filter out and slip our new Airaid filter in.



K-Source Custom Towing Mirrors Review - 2009 Dodge Ram

Today on our 2009 Dodge Ram Pick-Up we're going to do a test fit of part number ks80710 from K-Source. One part number covers both left and right side. To start off we're going to make sure that our mirrors are completely cleaned off. Then we can go ahead and install the new K-Source mirror.We'll take the top edge of the mirror, make sure the clips grab the top edge of the factory mirror on the truck and we'll slowly bring the K-Source mirror around the factory mirror. Then we'll make sure it latches underneath and that's really all it takes to snap on the mirror. A few more things to know about this mirror is it also has a cutout for the turn lights at the bottom of the mirror.The K-Source mirror can be moved independently of the factory mirror.



CargoGlide 1500XL Sliding Tray Installation - 2009 Dodge Ram

Today we will be installing our Cargoglide Sliding Tray on our 2009 Dodge Ram Quad Cab, part number cg1500xl-7548. To begin with you will want to clean the bed of your truck out. Next, youll want to position the cargo slider in the bed of the truck and youll want to center it between the wheel wells, as well as setting it about a half inch from the front of the bed. You will want to get the help of at least three other friends to help you set this unit into the bed of your truck. You will notice that the feet on this particular unit all bolt on the outside of the rails, and all of the locations are on the top section of the bed rib. Now that you see where the bolts will be drilled through, youll want to look under the bed and make sure there will be nothing in the way when you drill through.



Cipa Towing Mirrors Installation - 2009 Dodge Ram

Today, on our 2009 Dodge Ram 1500, well be test fitting the CIPA Custom Towing Mirror for the driver side, Part Number CM11401. Now, these slip-on towing mirrors give you an extra advantage when towing large boats or trailers giving you an expanded field of vision to help you when maneuvering these items down the road.Now, before we begin our test fit, well first need to put the soft foam padding on to the black bracket of our mirror. But for todays demonstration, we wont be installing the foam pad.Were now ready to begin our test fit. Well take our CIPA Custom Towing Mirror and slip it on to our Dodge Rams manufacturing mirror. You can notice the grooves. On the underside of the CIPA mirror, well slide directly on to the top and bottom of our Dodge Ram manufacturers mirror.Once the mirror is slid all the way on, well then move to the back of the mirror where well slide on our black clip.



CargoGlide Sliding Tray Installation - 2009 Dodge Ram

All right, today on this 2009 Dodge Ram pickup, we'll be installing part number CG1000-7548, from CargoGlide. First thing we're going to do is go ahead and take the assembly and go ahead and place it into the body of the pickup. We'll go ahead and put it into place and make sure we have it centered from left to right, and front to rear. You want to keep it at least a half inch away from everything around the bed of the truck. Once we have it centered the way we want it, we'll go ahead and slide it back. We'll pull back on the lash, then pull back on the cargo bed itself, leaving the frame in the bed of the pickup.



Rain-X Fusion Wiper Blades Installation - 2009 Dodge Ram

Today on this 2009 Dodge Ram pickup were going to do test fit of part number RX880005. This is the Rain-X Fusion windshield wiper blade. Few things to know about this windshield wiper blade is it is especially designed for use in rain, sleet and snow. It has a durable casing to help protect it from the snow and sleet and the rubber squeegee UV inhibitors help protect it from the sunlight. It also has multiple pressure points to help hold it against the windshield. To start off our test fit well go ahead and remove the original wiper blades.



Rain-X Latitude Wiper Blades Installation - 2009 Dodge Ram

Today on this 2009 Dodge Ram pickup were going to do test fit of part number RX5079277 from Rain-X. This is a latitude windshield wiper blade. Few things to know about this windshield wiper blade is that it has a beam style construction which insures a constant contact between the blade and the windshield. It has an aerodynamic shape to help keep it attached to the windshield during high speed. The rubber edge also has built in UV inhibitors to help protect it from the sunlight. To start off our test fit well go ahead and remove the original wiper blades.



Rain-X Weatherbeater Wiper Blades Installation - 2009 Dodge Ram

Today on this 2009 Dodge Ram pickup were going to do test fit of part number RX30220 from Rain-X. This is a weather beater windshield wiper blade. Few things to know about this part is that its designed to be an OEM replacement. It has a frame style design thats built from galvanized steel. It has multiple pressure points to help keep even pressure against the windshield blade. The rubber squeegee also has built in UV inhibitors to help protect it from the sunlight.



Bestop EZ Fold Folding Tonneau Cover Installation - 2009 Dodge Ram

Today, on our 2009 Dodge Ram Pickup 2500, we'll be installing the Bestop EZFolding Tonneau Cover, part number B1623901.Now, with our tonneau cover ready to be installed, we'll first remove the sealprotection, which is the white stripping along the outer edge. Now, with that removed,we'll go ahead and set the tonneau cover in position. When setting it in position, we'llalign the long edge with the front rail nearest the cab, and the short edges will line upwith the side rails that extend to the rear. And then we'll go ahead and get underneaththe tonneau cover, rotate the clamp down, and slide it over to the side rail. Then we'llrotate it until we pick up any extra slack and lock it into the inner lip of the bed rail.Now we'll go ahead and repeat the same process on the opposite side.Now, with both front clamps secured, we'll go ahead and fold the cover out. Onceagain, we'll go ahead and repeat the same procedure of pulling the clamps down,sliding them out into the bedrail, rotating them until we take up any extra slack, andthen locking them into position.



Trailer Hitch Installation - 2009 Dodge Ram - Hidden Hitch

Today on this 2009 Dodge Ram we're going to install part number 87530 from Hidden Hitch. First thing we're going to do is go ahead and lower our spare tire, we dont have to do this but it makes things a little easier to see. Next we'll go ahead and remove the trailer board cover from the top of the bumper. We'll use a screw driver to help push up it and out of the way. Next we'll go ahead and install the 3/4-inch hex bolt and conical toothwasher. When we put in place we'll make sure that the teeth on the conical toothwasher or pointed towards the bumper.



Trailer Hitch Installation - 2009 Dodge Ram - Draw-Tite

Today on this 2009 Dodge Ram Pickup, were going to install part number 75662 from Draw-Tite. First thing were going to do is go ahead and lower our spare tire. We dont have to do this, but it makes things a little easier to see. Next, well go ahead and remove the trailer ball cover from the top of the bumper. Well use a screw driver to help push up a knob away. Next, well go ahead and install the 3/4-inch hex bolt and a conical toothed washer.



Trailer Hitch Installation - 2009 Dodge Ram - Curt

Today on this 2009 Dodge Ram Pickup, we're going to install part number 13333 from Curt. This is what the hitch looks like once it's installed on the vehicle. Next, we'll go ahead and give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper will be about 1-3/4 inches. From the top of the receiver tube down to the ground will be about 20-1/4 inches. Now, I'll go ahead and show you how the hitch is installed.



Husky Front and Rear Floor Liners Review - 2009 Dodge Ram

Today on this 2009 Dodge Ram pickup 1500 series quad cab, we are going to do a test fit of the Husky liners weather beater custom auto floor liners, front and rear, this will be part number hl98011. These Husky liners are custom built to precisely fit the vehicle and stay in place. The shape, channels, and moldings all work to keep dirt and debride contained on the liner and not in your carpet. These liners can be easily removed from the vehicle, and washed, and cleaned with just soap and water. You can see how the liner matches the contour of the floor board and also has this ridge around here that keeps everything inside here and not leaking out towards the edge. The driver side liner has the same edge on the side; this has a provision for a factory hook.



Husky Front Center Hump Floor Liner Review - 2009 Dodge Ram

All right today on this 2009 Dodge Ram pickup 1500 series quad cab, we are going to do a test fit of Husky liners weather beater custom auto floor liner, this is for the front center hump, part number hl83711. All right at this point of our liner meets up even with the edge of the center console on the front here and the back; it also wraps down to the sides, you can use this with or without the floor liners. These Husky liners are custom built to precisely to fit the vehicle and stay in place. The shape, channels, and moldings all keep dirt and debride contained on the liner and not in your carpet. These liners can be easily removed from the vehicle, and wash, and clean with just soap and water. There you have it for part number hl83711 from Husky on our 2009 Dodge Ram pickup 1500 series quad cab..



Husky WeatherBeater Front Floor Liners Review - 2009 Dodge Ram

Today on this 2009 Dodge Ram Pickup 1500 Series Quad Cab, we're going to do a test fit of the Husky Liners WeatherBeater Custom Auto Floor Liners. We'll be using part number HL18011. These Husky Liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels, and moldings all work to keep dirt and debris contained on the liner and not in your carpet. These liners can be easily removed from the vehicle and wash and clean with just soap and water. You can see, we have the liner matches the contour of the floor board and it also has its ridge around here that keeps everything inside here and not leaking out towards the edge.



Trailer Hitch Installation - 2009 Dodge Ram

Today on this 2009 Ram Pickup, we're going to install part number 14374 from Curt. This is what the hitch looks like once it's installed in the truck. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper, we're looking at 2-1/4 inches. From the top of the receiver opening down the ground, we're looking at 19-1/4 inches. Now, we'll go ahead and show you how it's installed.



Timbren Rear Suspension Enhancement System Installation - 2009 Dodge Ram

Today on this 2009 Dodge Ram 1500, we're going to install part number TDR1500DQ from Timbren. First thing we need to do is go ahead and raise the vehicle up and then we'll go ahead and remove the factory bump stops. Alright, now we've got the old ones removed, we'll now go ahead and install the new Timbrens. We'll go ahead and spray some soapy water on it. And now our Timbren has already come pre-assembled in a package, so all we got to do is install it on the vehicle. We're going to fit up into the cup right here. So what we'll do, we'll start it, put in place with little piece of timber between two and lower the truck onto it so it pushes the Timbren part up into the cup.



Derale Engine Oil Cooler Installation - 2009 Dodge Ram

Today on this 2009 dodge 1550, were going to install a Deralle performance kit. This is an engine oil cooler kit, part number d15551. Were going to take our inch NTP by inch far Inaudible 00:00:14 fittings, apply some thread tape, lets go ahead and do that that now. Quick tech tip when putting on your thread tape is to make sure youre going with the thread so when youre installing it, it will help seal up and lock in the thread tape and install them on both the filter mount and spin on adapter. That completes our first one, were going to go and repeat the same process for the other 3. Our next step is going to be accessing the engine compartment and were going to remove a couple of trim panels so we can remove the grill to get access to mount our new oil cooler.



Thule AeroBlade Traverse Roof Rack Installation - 2009 Dodge Ram

All right today on us 2009 Dodge-Ram 1500, we going to test fit our Thule roof-rack system, were using Thule sixty inch aero blades and well be using the rapid traverse foot pack, we have roof rack already assembled according to the instructions so lets go ahead and put them on of the roof of the truck. Well start of by opening the doors and well go ahead and put our first crossbar towards thefront windshield then place first. To put the crossbar in correct spot wed need to measure from the edge of the windshield to the leading edge of the foot pack. Now, lets go by on the instructions but in this case its going to be four and a quarter inches. Okay, well go and install the second crossbar, just like we did first one except when measuring off the center of the first crossbar to properly place the second crossbar. Okay, so Im measuring the center from the first crossbar to second crossbar center well be 31 inches.



Husky Shield Headlight Protectors Installation - 2009 Dodge Ram 1500

Today on this 2009 Dodge Ram 1500 were gonna be installing a Husky Shield Headlight Guard System from Husky Liners part number HL06647.The headlight guards are a fin thats going to go over the surface of our headlights to protect them from road debris, bugs and exposure to the sun.First thing we need to do before installing the headlight guards is to prep our surface. Included with the headlight guards as well as the installation kit are small pieces of clay. These clay bars are going to be used to remove debris bugs and any embedded particles off the surface of our headlights. Weve take a spray bottle and made a soapy water solution that well use to lubricate as we run the clay across the surface to clean the headlights. Youll feel little bits of debris that are embedded in the plastic come up. Youll also feel things like bug guts and other dirt come off as you slide the clay on the surface.



Yakima Q Tower Roof Rack Installation - 2009 Dodge Ram 1500

Today on this 2009 Dodge Ram 1500 Quad Cab, we are going to be test fitting a Yakima Q Tower roof rack system. We will be using a 4-pack of the Yakima Q Towers along with the Q7 clips on both the front and rear crossbars. We will also be using Yakima 58-inch round crossbars. We already have our crossbar assemblies put together and ready to install. So, first, we will open up the front doors, so we can position the front crossbar. To position the crossbar, we will need to measure 10 inches from the edge of the windshield to the edge of our Q Tower. Once we have the crossbar into position, we can go ahead and set our towers and lock them down. You will also want to check your position and make sure that the crossbar is even on both the passenger side and driver side. You do not want to have to force the door closed, but you do want it good and snug. Once we have the front crossbar in position, we can go ahead and get ready to install the rear. 0:52



Trailer Brake Controller Installation - 2009 Dodge Ram 1500

Today we are going to install the Tekonsha Primus IQ brake controller on a 2009 Dodge Ram 1500. We will also be using the Tekonsha wire harness, part number 3020-P. The Primus IQ is a proportional style brake controller. It sense how hard or how softly you are braking in the vehicle and sends the proper voltage to the trailer brakes so the whole braking action is smooth and even. It features a digital LED display and also has three levels of boosts to increase or decrease the trailer braking power as needed. It can be mounted between 0 degrees and 70 degrees nose up. And it is covered by a limited lifetime warranty. In the packaging for the brake controller, you will find the brake controller itself, as well as a fixed black plastic mounting bracket and a black metal bracket that we will not be using. You will also find a packet of screws for attaching the bracket to the vehicle and the controller to the bracket, as well as a generic harness with loose wire ends. But since we have our custom fit harness today, we will not be using that wiring. Let us head to the vehicle. 1:13



Firestone Work-Rite Load Assist Installation - 2009 Dodge Ram 1500

Today on this 2009 Dodge Ram 1500 we are going to install part number F8620 from Firestone. This is their Work-Rite Load Assist. To give you an idea of what is going on the new Firestone part actually replaces the factory bump stop right here. When you have the truck fully loaded, the only way it is going to stop is when it hits this bump stop and goes down to the axle. You can see we have got quite a bit of difference so if we put a load in the back of the truck or bounce up and down the road you can see how much travel this has. 00:28



WeatherTech Window Visor Installation - 2009 Dodge Ram Pickup 1500

We are going to be installing WeatherTech side window deflectors, part number WT80503. So, I am going to start by installing it here at the front, making sure that this piece is on the outside. We are going to the recessed areas and these are in channel visors. So we want the top sections, the thinned out portion, to go ahead and to sit inside the channel. And then with the front corner ed, we just actually want to go to t he rear section of the air deflector. When it is just sitting on top, it actually overlaps the door quite a bit. So what we are going to have to do is actually fold it down so that it can be ed into the channel. You can see there is quite a bit of flex in t he window visor. You want to make sure that you are not installing this in any weather that is under 50 degrees because that bending of the visor could actually crack the visor if it is not warm enough. 0:47



WeatherTech Mud Flap Installation - 2009 Dodge Ram 1500

Today on this 2009 Dodge Ram 1500 series pickup, we will be installing the WeatherTech mud flaps front and back, part number WT110024-120024. We are going to start our installation with the front mud flaps and we are going to start on the driver side. The first thing we want to do is go ahead and turn our front wheels all the way to the left to maximize the clearance between the tire and the fender well. Next we want to locate our mud flap. And on the back side you will see that they are marked L.H. for the left hand side and R.H. for the right hand side. We want the L.H. one for the driver side here. Before we get our installation started, we want to make sure that this area is nice and clean so that the grime does not build up in between our mud flap and our fender well. The mounting holes that we are going to be using for our mud flap are going to be this one here, into the existing hole here in the fender well. And we are actually going to remove this screw here from the bottom and reuse it to install the mud flap. 0:56



Trailer Wiring Harness Installation - 2009 Dodge Ram 3500 Series

Today on this 2009 Dodge Ram 3500 Series we will be installing the fifth wheel and goose neck wiring harness part number V30137. The first thing I want to note before we get started is that our harness comes in two separate pieces. We have got the 7-pole which is what we are going to be mounting in to the bed of the truck and then we have got the wiring harness itself. The wiring harness has two different ends on it. The one end of the wiring harness has a larger round plug and that is what is going to plug directly into the back of our 7-pole. The other end which we are going to feed down through the opening in between the bed and the fender well has the two square ports. The first thing I am going to do is drill out the hole in the bed for the 7-pole. We are going to be using a two inch hole saw to accomplish this. Next we are going to feed the square ports through the hole that we just drilled down underneath the vehicle. Then we want to plug in the round port into the back of the 7-pole and we just want to make sure we hear the snap so that we know that the two ends are engaged. 01:00



Trailer Brake Controller Installation - 2009 Dodge Ram Pickup

Today on this 2009 Dodge Ram we will be installing the Tekonsha P3 brake controller along with the wiring harness for it, part number 90195-3020P. The first thing I want to point out is the factory installed 7-pole at the rear of the vehicle and this will be the indicator of whether or not your vehicle is going to have the factory installed brake control port under the dash. The factory 7-pole we are looking for is built into the bumper. It will have the Chrysler logo built on the front. If you do not have this plug you will likely not have the port under the dash that we are going to be plugging into. Thus will have to hardwire your brake controller into the vehicle. 00:38



Fifth Wheel Hitch Kit Installation - 2009 Dodge Ram 3500 Series Mega Cab

Today on this 2009 Dodge Ram 3500 Series Mega Cab we will be installing the signature series rail kit part number 30074. The first thing we want to do in preparation to installing our cross members under the bed is to remove our spare tire and get it out of the way so we have some more working room. The cross members we are going to be installing are going to be sitting in between the two hat channels right above the exhaust and over top of the gas tank as well. On standard models you can follow the directions to fit the cross members in from underneath the bed and just manipulate them into position. However on this mega cab model the spacing is not there for us to do that so what I am going to do is loosen up the bed and slide the cross members in from the outside of the frame directly across over the top. 00:48



EGR Bug Shield Installation - 2009 Dodge Ram 2500

Today we are going to install part number 392354 from EGR. This is a chrome bug shield. We are going to install this on a 2009 Dodge 2500 Full Size Pickup. All right we will show you where it mounts up on the vehicle itself. The bug shield is going to actually go between this part of the grill and the hood. We will slide the unit in between the hood and the grill and tighten it back up. Lets go ahead and pop the hood open and loosen the screws.



Putco Window Visor Installation - 2009 Dodge Ram

Today we are going to install part number P580178 from Putco, and we are going to install this on a 2009 Dodge Ram full-size pickup. These vent visors will install in the channel with the window, and these will actually have a little bit of adhesive on them to help them stick to the inside of the channel of the door itself. The track that the vent visor fits into is right here, all the way down. And what happens is that the adhesive on the vent visor itself will actually attach to this inside edge on top up here, inside this edge right here. So before you peel the backing off the adhesive, it is a good idea to always do a test of it first. So let us put it right in the channel and just pop it into place. Then you have a good idea of where the adhesive sticks onto the weatherstripping here.





2009 Dodge Ram Pickup Questions and Answers


  • 5th Wheel Trailer Hitch Installation Kit for a Reese Hitch on a 2009 Dodge Ram 2500 Long Bed
  • For your 2009 Dodge Ram 2500 I recommend going ahead and getting a complete new kit, # C16420-204. The reason for this is that you should not mix rails and brackets from 2 manufacturers because the capacity will be unknown, and because you would likely need new hardware anyway to install the rails you do have to the new brackets since the hardware is meant for one time installation. I have included a link to a video showing installation of the Curt kit and its instructions. You can use the
    view full answer...

  • Will the Putco LED Roof Lamps, # P930534, Fit a 2009 Dodge Ram 1500 Pickup
  • Putco offers Pure LED Roof Lamps with Ion Chrome Lens, # P930556, to fit a 2009 Dodge Ram Pickup. Putco also offers two additional lens choices to fit the 2009 Ram should you be interested. LED Roof Lamps with Smoke Lens, # P920556, and Clear Lens, # P900556. The part that you referenced, # P930534, fits a 1999 - 2001 Ram Pickup and 2002 Ram 2500 and 3500 Series. I spoke with my contact at Putco and she said that due to the lights fitting the contour of the vehicle, each item is specific to
    view full answer...

  • Can the Spring Bars Slip Out of a Dual-Cam Sway Control
  • What keeps the bars from slipping out of the cams around turns is the fact that the movement of the bars is pretty minimal under normal circumstances. In order for the end of the bar to be pulled out of the cam the degree of the turn would be sharper than what would be seen under normal circumstances. Basically as long as you install the dual cam system of the Strait-Line Weight Distribution System part # RP66087 properly you would not have to worry about the spring bars riding up the cams fa
    view full answer...

  • Parts Needed to Convert Pro Series Weight Distribution System to Strait-Line Dual Cam Sway Control
  • You will need to but new spring bars, a new weight distribution head, and the sway control unit itself, but yes you can do it. The reason you need to replace the spring bars is that you need the spring bars with the bend ends for the cams to ride on. For that you would need a quantity of 2 the Replacement Round Bar Part # RP58115. Your current weight distribution head is not compatible with the heavy duty spring bars. For a replacement head you will need the Replacement Head part # RP58112
    view full answer...

  • Availability of DeeZee Tailgate Assist for 2009 Dodge Ram 3500
  • For the Ram 3500, you would want to use the DeeZee Tailgate Assist, part # DZ43300. You can order online by using the provided link, or by calling our Customer Service folks at 800-298-8924.
    view full answer...

  • Installing a Gooseneck Hitch on a 2009 Dodge Ram 2500 with 5th Wheel Base Rails and Brackets
  • To install a gooseneck hitch, like the Draw-Tite Remov-A-Ball # 6300-4435, on your 2009 Dodge Ram 2500, you will have to remove the fifth wheel base rails and frame brackets. Fifth wheel frame brackets and gooseneck frame brackets use the same mounting locations on the frame rails and manufacturers do not recommend stacking brackets. If you do not want to remove your fifth wheel base rails, there are a few options to adapt a gooseneck trailer to a fifth wheel hitch/base rails. Since you do n
    view full answer...

  • Westin Grille Guard Recommendation for a 2009 Dodge Ram 1500 Sport
  • The Westin Sportsman Grille Guard # 40-3545 is a Westin grille guard that will fit the Sport model trucks. The only exclusions are vehicles with adaptive cruise control, or forward collision warning systems that feature grille mounted laser control sensors. The Westin HDX Grille Guard # 57-1955 that you referenced would not fit the Sport models so I would not recommend it for you.
    view full answer...

  • Will K Source Snap-On Towing Mirrors Fit a 2009 Dodge Ram with Factory Power Mirrors
  • The K Source towing mirror set # KS80710 will fit your 2009 Dodge Ram as long as it is a 1500 series and does not have extendable or telescopic mirrors. If your mirrors are like the ones in the video I have linked then they will fit. A passengers side and drivers side mirror are included for a total of 2 mirrors.
    view full answer...

  • 2009 Dodge Ram 1500 Squats when Towing Livestock Trailer
  • When vehicle squat is caused bu the tongue weight of a trailer the best solution is to use weight distribution on the trailer. Weight distribution will distribute the tongue weight of the trailer more evenly to all axles of the tow vehicle and trailer and take care of that squat. In order to determine the correct system for you I would need to know the total tongue weight. This is calculated by taking the tongue weight of the trailer when loaded and ready to tow and adding to that the weight
    view full answer...

  • Will 5th Airborne Sidewinder 5th Wheel Air-Ride Coupler # ST500-5AS02 Fit 2009 Ram 3500 MegaCab
  • The 5th Airborne Sidewinder 5th Wheel Air-Ride Coupler # ST500-5AS02 is intended for use with 5th wheel hitches on short-bed trucks. Replacement pin boxes need to be matched based on the original pin box on the 5th wheel trailer in order to ensure bolt-on compatibility. This particular 19K pin box is a direct replacement for Youngs Welding standard and extended pin boxes, but will not fit in place of their tube style coupler. You will want to verify which pin box is installed on your trailer
    view full answer...

  • 5th Wheel Trailer Hitch Installation Kit for a 2009 Dodge Ram 2500 Short Bed Quad Cab
  • The R-Series hitches, # RP30869 for 16K slider or # RP30870 for 20K slider, used to have an issue hitching up when using a lube plate but that issue has been resolved. There is actually a special lube plate specially designed to fit the unique head on the R-Series hitches, # 83003. As far as the installation kit goes, # RP50082-58 is for Fords so that is not going to fit your 2009 Ram. Between # RP50140-58 and # RP56011-53 you are correct, # RP56011-53 is going to be easier to install because
    view full answer...

  • Is there a Mounting Bracket for Trailer Back Up Light # BU33CB
  • There is no bracket for external mounting of grommet # A33GB so you will have to cut a hole where you want the grommet and light to go. Use the grommet as a template to cut the hole. Start small because you can always work your way up to a larger hole if needed.
    view full answer...

  • Is the Pilot Trailer Brake Controller Compatible with Electric Over Hydraulic Braking Systems
  • The Pilot brake controller # 80550 does not work with electric over hydraulic braking systems. We do have some controllers that are compatible: P2, # 90885 P3, # 90195 X10, # TM75813 The wire colors have the same functions on these controllers as the Pilot does. If you want to add a new wiring harness for the new controller use # 3020-P for the P2 and P3 or # TM76281 for the X10.
    view full answer...

  • Suspension Enhancement Recommendations for a 2009 Dodge Ram Quad Cab Dually and Gooseneck Hitch
  • The installation kits for gooseneck and 5th wheel trailer hitches often times will occupy the same space needed by suspension enhancement and so there can be interference issues. What you want to look for is a suspension enhancement kit that does not install in the same places as your hitch. I recommend the Timbren springs, # TDR1500DQ for a 1500 series 2009 Dodge Ram because they fit in place of the factory bump stops. They will help prevent squat and improve ride quality. Best of all becaus
    view full answer...

  • Do the Same Running Boards Fit Both a 2009 Dodge Ram Crew Cab and Quad Cab
  • Quad Cab and Crew Cab models on the 2009 Dodge Ram take different model numbers of running boards. For the DeeZee FX model for example, on a 1500 Quad Cab you would use # DZFX31928 and on a Crew Cab you would use # DZFX31930. I have included a link to the tube step and running board main page for the 2009 Dodge Ram for you.
    view full answer...

  • 5th Wheel Hitch To Fit Either 2013 Flagstaff or 2014 Rockwood RV Using a 2009 Dodge 1500 5-1/2ft bed
  • The hitch installation measurements will be the same when installing a 5th wheel hitch in your 2009 Dodge 1500 Crewcab shortbed no matter which 5th wheel trailer you choose. Considering your vehicle and your trailer options, I recommend using the Reese 16K Premium Double Jaw # RP30866. The main reason I picked this unit was because it is a double jaw system which is good for secure towing, and most important, it has a vibration-isolator-system that reduces jarring. The custom base rail moun
    view full answer...

  • How to Designate a 2009 Dodge Ram From a 2009.5 Dodge Ram For a Pop and Lock Tailgate Lock
  • The Pop and Lock # PAL8350 that you are referencing will fit either version of the 2009 Ram. I have found that if your 2009 Dodge Ram was built after March 4, 2009, it is considered a .5, however, for a definite answer, the easiest way is to call your local Dodge dealer with your VIN. In my research, I have found that the differentiators between the 2009 and 2009.5 are all across the board ranging from the internal computer upgrades to the Dodge branding to the physical structure of the ve
    view full answer...

  • TruXedo Roll Up Soft Tonneau Cover for a 2009 Dodge Ram 1500 Short Bed
  • The TruXedo TruXport Soft, Roll-Up Tonneau Cover # TX244101 fits 2002 Dodge Ram Pickup 2500 and 3500 Series, 6 Foot Bed and 1994 - 2001 Dodge Ram Pickup 6 Foot Bed. But it does not fit a 2009 1500. For a 2009 Dodge Ram 1500 short bed (6 foot bed) you can use # TX246901. For a 5-1/2 foot bed with the Ram Box feature use # TX544955. For a 5-1/2 foot bed without the Ram Box use # TX245901.
    view full answer...

  • Will the Rola Enclosed Cargo Carrier # 59110 Work With 2009 Dodge Ram Laramie with Dual Exhaust
  • Since the exhaust on your 2009 Dodge Ram Laramie points straight back, it is recommended to use exhaust tips to direct the exhaust flow downward or away from the the Rola Enclosed Cargo Carrier, # 59110. The platform of this cargo carrier will sit approximately 10 inches away from your rear exhaust and at that distance, the heat from the exhaust could potentially damage the plastic of the cargo carrier. Your truck likely already has exhaust tips installed, if those exhaust tips are removable,
    view full answer...

  • What 5th Wheel Hitch for a 2009 Dodge Ram 2500 Single Cab with 8-Foot Bed Towing 30-Foot Camper
  • The Pro Series 5th Wheel Trailer Hitch with Rails and Installation Kit, part # PS30128, is an economical universal-fit item that will work in your 2009 Dodge Ram 2500 with 8-foot bed. This is a complete 5th wheel system that includes the 5th wheel hitch head assembly, base rails and a universal installation kit. However, a better option is a custom base rail/bracket installation kit. Custom kits will cut your installation time in half. The Pro Series 15k hitch head # PS30093 and custom insta
    view full answer...

  • What is the Diameter of the Round Base on Ultra-Fab Stackable Stabilizers, # UF48-979004
  • I went out to the warehouse and measured the round base that contacts the bottom of the trailer for Ultra-Fab Stackable Stabilizers, # UF48-979004. It measures 1-3/4 inches in diameter. I made a video with this information and a picture as well. In terms of using this item to support a door to create a porch on a trailer you will have to determine if the door is rated for the weight associated with being a porch. The construction of the door may not be conducive to porch-ness.
    view full answer...

  • Replacement Hardware Kit for Bumper Mounted Tire Carrier, # TR-1
  • We do have a replacement hardware kit for the Stromberg Carlson spare tire carrier, # TR-1. You will need replacement hardware kit # TR-2200.
    view full answer...

  • Which Underbed 5th Wheel Rail System and Adapter to Install AirSafe 20K Hitch in 2009 Dodge Ram 2500
  • You are correct that you will need an under-bed rail system and adapter to install an AirSafe 20K 5th wheel hitch in your 2009 Dodge Ram 2500 Quad Cab. You can use the Reese Under-bed Fifth Wheel Installation Kit, part # RP30074, which is rated at 18,000 pounds. Hardware is included. I have included a video link for this part showing installation in a 2009 Ram. The under-bed rail adapter you can use is part # RP30156. I spoke to a representative at AirSafe and he confirmed that their 20K
    view full answer...

  • 5th Wheel Trailer Hitch Recommendation for a 2009 Dodge Ram 2500 Quad Cab Short Bed
  • On a short bed truck like your 2009 Dodge Ram 2500, you will need a slider hitch. But first, you will need an installation kit. I recommend the custom installation kit # RP50140-58 because it installs in less time and requires less drilling. I have included a link to the installation instructions for you. Because clearance between the truck cab and the trailer will be a concern on a short bed truck when making tight turns, I recommend a round tube slider because they offer the most travel (12
    view full answer...

  • Recommendation for a Removable Wheel Chock
  • The mounting hardware included with the MaxxTow adjustable wheel chock, # MT70075, is designed for a permanent installation. However we do have several wheel chocks that are considered removable because of how they mount. We have TowRax chock # TWSPWM, # TWSPWC, # TWSPWC3BT, and # TWSPWS. These chocks have a keyhole shape opening where the large end fits around a bolt head. When the bolt is tightened down on the skinny end it cannot be removed. When the hardware is loosened, the chock can be
    view full answer...

  • 5th Wheel Recommendations for 2009 Dodge Ram 1500 Crew Cab with 5-1/2-Foot Bed
  • We do have an option for you, but it will not be the installation kit # RP30035-023 as it will not fit the 5-1/2-foot bed of your 2009 Dodge Ram 1500. After speaking with representatives of Reese who are currently visiting us here at etrailer, I recommend the Reese Semi-Custom Base Rail Installation Kit # RP30035-386 as it features a mounting kit made specifically for your truck. The kit includes base rails, universal brackets, semi-custom brackets, and hardware. I have provided links to the
    view full answer...

  • Front and Rear Suspension Enhancement for a 2009 Dodge Ram 2500 4x4 Mega Cab
  • Using Firestone Ride-Rite system # F2299 can be used to level the truck when carrying heavy loads. If you install the front system # F1004 you will not need to have anything adjusted by a shop. I have included links to the instructions for each of these products for you. To reap the full benefits of these systems I recommend a Level Command kit with onboard compressor, # F2219. Otherwise you will have to manually monitor and fill the air system every time. But to keep you out of the pig ho
    view full answer...

  • Putco PURE Premium Replacement LED Dome Lights for 2009 Dodge Ram
  • The Putco PURE Premium LED Dome Light Kit you referenced, part # P980044 includes LED assemblies to replace the existing two map lights in the headliner console as well as the dome light, for a total of 3 LED assemblies.
    view full answer...

  • Where Does the Westin Off-Road Light Bar Mount to on a 2009 Dodge Ram
  • I attached a picture that I took from the instructions for this Westin Off-Road Light Bar # 37-02580 that you referenced that details how it installs and has pictures of the installation as well. It looks like it attaches to the same location as your tow hooks, but you will not have to remove your tow hooks to complete the install.
    view full answer...

  • Fifth Wheel/Gooseneck Wiring Harness for 2009 Dodge Ram 1500
  • The Fifth Wheel/Gooseneck Wiring Harness you referenced, part # PK11893-11932 is indeed the recommended wiring harness for your 2009 Dodge Ram 1500. The harness plugs inline at the connection behind your existing trailer connector, as you can see by watching the video I have linked you to.
    view full answer...





Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 17 Hours 1 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com