Chevrolet Lumina owners are most interested in these products
change vehicle
Trailer Wiring Harness Installation - 1994 Chevrolet Lumina
Today we're working on a 1994 Chevy Lumina. We're going to install the Draw-Tite four-pole connector, part number 18252. Our first step is going to be to remove the rear threshold of the vehicle. We've got a total of four fasteners. We've got two screw fasteners on each side and two pushpin fasteners. The pushpin fasteners are easiest to just unscrew for the flat bladed screw driver.
Trailer Wiring Harness Installation - 1996 Chevrolet Lumina
Today on this 1996 Chevrolet Lumina we are going to install part number 18252 kit. What we have to do is hard wire it on to the existing harness, it is not a plug in or anything like that. At least we can get to the wires pretty easily in the vehicle. Everything we need to get to is right behind this tail light. Undo the carpeting, get this knob out of our way first. Pull it back out of our way. This is the wire harness we can get at for everything we need. Peel the loom away. What we are going to do is turn on the running lights in the vehicle and find out what the functions are going to be. On our 4-pole wiring connector we need to find out what the running light circuit is. This brown wire is our running light circuit so brown to brown in this instance. Now work on the right turn signal. The right 4-pole harness is going to be green. Now we will do our left turn signal that is going to be yellow to yellow. 01:00
Trailer Hitch Installation - 1996 Chevrolet Lumina
Today on this 1996 Chevrolet Lumina we are going to install part number 24628 from Draw-Tite. Our first step is to remove the rubber hangers from the exhaust bracket and this exhaust bracket here we are actually going to be removing because there is a third hanger behind the muffler that should hold up everything just fine so we do not have to worry about damage. We are looking at the passenger side of the vehicle. If your vehicle had dual exhaust then you are just repeating the same steps on both sides. This is our exhaust bracket that we took off. We have it oriented right now the way it was sitting on the vehicle. The part we have to remove is this part right here. We just have to cut this little part off and basically we can just start reassembly and the installation in the hitch. 00:50
Chevrolet Lumina Questions and Answers
- How to Determine Proper Fit for Snow Chains on a 1997 Chevy Lumina
- Our fit guide recommends tire chains by tire size only, and the tire sizes listed are the OEM sizes normally found on the specific year-make-model of vehicle you input.
Due to modifications that may have been done or suspension wear, you are responsible for checking your vehicle owners manual and actual clearance on the vehicle to determine if the tire chains will have clearance when installed on the tire. Many manufacturers recommend Class S or smaller tire chains for their vehicles, which r
view full answer...
- Which is Correct Ball Mount for 1997 Chevrolet Lumina w/ Draw-Tite Trailer Hitch # 24628
- The recommended ball mount to use on a 1997 Chevrolet Lumina with the Draw-Tite Trailer Hitch, part # 24628 is the Draw-Tite Ball Mount, part # 3592.
The ball mount that you referenced, part # 3594 has too much of a rise and is not recommended by Draw-Tite to be used on the Chevrolet Lumina. With Class I and II hitches, the ball mount recommended by the hitch manufacturer must be used, not doing so will void the hitch warranty.
I have linked an FAQ on hitch ball mounts.
view full answer...
- Can Roadmaster Base Plates be Used with Blue Ox Tow Bars to Flat Tow a 1998 Chevy Lumina
- We do have adapters to allow the Roadmaster Base Plates, # 172-5, to work with Blue Ox tow bars. If you have an Aventa, Aventa II, Kar Bar, Aladdin, Alexxa, or Acclaim RV-mounted tow bar, or an A-frame Blue Ox tow bar with 1 or 3 pronged attachments, you can use RoadMaster Base Plate to Blue Ox and Demco Tow Bars Adapter, # RM-033 or # RM-032. Base plate installation can be moderately difficult, but if you have experience with automotive projects you will be able to perform the installation at h
view full answer...
- Installation Instructions For The Draw-Tite Trailer Hitch, # 36124, On A 1993 Chevy Lumina
- I am sending a link with the installation instructions for the Draw-Tite Trailer Hitch, # 36124, fitting on a 1993 Chevy Lumina.
view full answer...
- Does the Derale Transmission Cooler Kit Come with What is Needed to Install on a 1997 Chevy Lumina
- The Derale Dyno-Cool Tube-Fin Transmission Cooler Kit, # D12906, comes with everything you will need to mount and install it on your 1997 Chevy Lumina. The system installs in line with your current transmission hoses.
I have included an FAQ article on Transmission Coolers below. There is a lot of helpful information, including the best places to mount the unit. I have also included a video showing installation of a transmission cooler. Installation will be similar on your vehicle.
view full answer...
- Does a 1995 Chevy Lumina Trailer Hitch Require Drilling?
- For your 1995 Chevy Lumina you will be required to drill two 1/2 inch holes in the underside of the bumper and cut off, with a hacksaw, the end of the exhaust hanger. If you have dual exhaust, you will have to cut the end of the exhaust hanger on both sides. For a no drill installation you could order the Hidden Hitch 90040 hitch which would only require cutting the exhaust hanger. It also comes with the draw bar, pin and clip. This is a Class II hitch with more capacity and more options availab
view full answer...
all Chevrolet Lumina questions
