See what our Experts say about this Draw-Tite Accessories and Parts

• Recommended Trailer Hitch And Wiring For A 2025 Kia Sorento PHEV
  Hi Jerry, For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver # C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have, you can install a 7-way connector like the Tekonsha # TK24FR. Regardless of the tow package you can install a 4-pole connector like the Tekonsha # 118269 (incandescent tail lights) or Curt # C99DR (LED tail lights). The 7-way is really...
  view full answer...
  
• How To Install a 7-Way Trailer Connector On a 2015 Jeep Wrangler Unlimited with Factory 4-Way
  I have exactly what you need to install a 7-way trailer connector on your 2015 Jeep Wrangler Unlimited. It sounds like you have the factory tow package therefore, all you would need to do is remove the 4-way you have now and replace it with the Hopkins Endurance Quick-Install 7-Way Trailer Connector part # HM42190. This will make for a completely plug and play installation. In order to mount the trailer connector onto the vehicle I also recommend the Mounting Bracket for 7-Way part # 18138. For...
  view full answer...
  
• How To Tell If a Ford Transit Has the Tow Package and Parts Needed To Add It
  The Ford Transit if equipped with the factory tow package would have came with both a trailer hitch and trailer connector and they would both be located directly under the rear bumper so odds are you do not have either because they are not hard to locate. The factory tow package was also not a very common option but I can provide you with everything to add this on your own at a fraction of the price. The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75912 is a confirmed fit for a 2015...
  view full answer...
  
• How to Mount a Trailer Connector to a Trailer Hitch Receiver
  Yes, we sure do! In order to mount your trailer connector on the rear of your vehicle, you will want to use part # 18140 along with part # 18144 for 4-way or part # 18136 along with part # 18138 for 7-way trailer connectors. I have attached a review video of the no-drill mounting bracket for you as well.
  view full answer...
• Replacement Bracket for a 7-Way Connector on a 2010 Chevy Silverado
  Although we do not have a cover that takes up that whole space, I do have a way that you potentially mount your 7-Way at your rear bumper on your 2010 Chevrolet Silverado. You could use the Mounting Bracket for 7-Way # 18138 by disconnecting the 7-Way connector and then feeding the wiring harness and plug through the hole in the bracket. You can then either mount it using the included self-tapping screws. i have attached a video of this process being done. If you will be driving the screws...
  view full answer...
  
• Receiver Mounted Trailer Wiring Harness Mounting Bracket for a 1-1/4 Inch Trailer Hitch Receiver
  I have a couple solutions that will work for you. At this time, the only receiver mounted bracket for a trailer wiring harness available is for a 4-way trailer connector, part # C58002. I've attached a picture that shows how it mounts and how the 4-flat wiring harness fits. Again, this is the only wiring harness bracket that mounts to a 1-1/4 inch receiver. They don't make a bracket for a 7-way trailer connector because most vehicles with a 1-1/4 inch receiver aren't towing trailers with...
  view full answer...
  
• Trailer Wiring Harness Recommendation for a 2008 Honda Ridgeline
  Yes, the CURT T-Connector Vehicle Wiring Harness with 4 Pole Trailer Connector # C55585 is the correct wiring harness for your 2008 Honda Ridgeline. To install this kit you will basically just need to access the tail light harness on both sides of the rear of your vehicle and install the harness from the # C55585 inline with it. Check out the installation instructions I attached that detail this also. If you need a 4 to 7-way adapter for a trailer that does not have electric brakes you...
  view full answer...
• Recommended Towing And Roof Rack Components For A 2019 Hyundai Santa Fe
  Hi Linda, For a 2019 Hyundai Santa Fe you'll want the etrailer Trailer Hitch Receiver # e98843 for the hitch and the Tekonsha T-One Vehicle Wiring Harness # 118784 for the wiring. A 2" trailer hitch is definitely the way to go since most accessories are made for 2" hitches and if you had a 1-1/4" accessory you could just use an reducer sleeve. To mount the 4-pole connector to the trailer hitch crossmember you can use no-drill mount # 18140. You'll still need a ball mount to tow a trailer...
  view full answer...
• Connecting Ignition Switched Power From 2015 Toyota Prius v to Enclosed Trailer
  You will need to use a circuit tester like # PTW2979 to find a wire in your 2015 Toyota Prius v that is hot only when you use your key (ignition switched power). When you do that you can simply wire in the Battery Isolation Solenoid # PK5231201, which should be wired like in the accompanying diagram with 10 gauge wire # 10-1-1. I have added a link to a video review of the solenoid for you to check out.
  view full answer...
  
• Bracket To Attach 7-Way To 2017 Mazda Cx-5 Curt Hitch
  We have quite a selection of mounting brackets. My favorite that will fit your Curt Trailer Hitch Receiver # C13315 is the Mounting Bracket for 7-Way # 18138. The hose clamp is used to secure this bracket to the trailer hitch. I have attached a link with some available brackets to this answer page.
  view full answer...
• Parts Needed to Tow Tent Trailer With 2011 Mercury Mariner
  The wiring you will need for your 2011 Mercury Mariner is T-One Harness # 118551, which will give you a 4-way connector. To use that with the 7-way on your tent trailer you would need to use the 4 Pole to 7 Pole Vehicle End Trailer Connector # 30717, which provides connection points for both your vehicle and trailer's plugs. To mount the adapter you may want to use no-drill bracket # C57202 along with Mounting Bracket for 7-Way # 18138. You can see how to mount this adapter in the video...
  view full answer...
• Installation of Tekonsha Voyager Brake Controller on 2014 Chevy Traverse
  We have many brake controllers so I would need to know which one you are specifically asking about as well as the year of your Traverse. If you can get back to me with that info I would be happy to answer your question as best as I can.
  view full answer...
• Which Harness do I Need For My 2004 Ford Ranger
  Thank you very much for your question, and I'm sorry about the confusion, but we shall clear things up right now. Since your 2004 Ford Ranger is already complete with a tow package and a 4 pin connector, depending if you want to use a brake controller or not to control the brakes on the trailer will determine the solution for this question. First, I will give you instructions for If you were not planning on using a brake controller. The product you need is a 4 pole to 7 pole adapter #...
  view full answer...
• Recommended Towing Set Up w/ Bike Rack for a 2019 Chevrolet Traverse w/ Tow Package
  Hey Dave, I would be more than happy to share my opinion on your set up and offer a couple recommendations. I looked up your 2019 Chevrolet Traverse High Country and it's got a maximum towing capacity of 5,000 lbs. This would be a great tow vehicle for the travel trailer you're looking at or already own. The tow package doesn't include a brake controller or a 7-Way in some cases. Both of which you will definitely need to haul a trailer with brakes. For a 7-way connector, you'll want the...
  view full answer...
• What Trailer Connector Mounting Bracket Is Needed For A Trailer Hitch On A 2005 Toyota 4Runner
  Yes, the tech note you referenced for the Curt Trailer Hitch Receiver # 13445 is meant to take you to either the No-Drill Mount for Electrical Mounting Bracket - Short # 18140 or long # C57202. These no-drill brackets have a hose clamp that will wrap around the cross-tube of the hitch for an easy mounting point for the trailer wire harness connector. The long bracket is approximately 6-5/8" long and the short bracket is 3-13/16" long. If you plan on installing a 7-way connector then you'll...
  view full answer...
• Recommended Trailer Hitch and Wiring for 2022 Mercedes-Benz Sprinter 2500 with Step Under Bumper
  The trailer hitch I recommend for a 2022 Mercedes-Benz Sprinter 2500 with factory step bumper is the etrailer Trailer Hitch Receiver part # e82TR which offers a direct bolt-on fit so there's no drilling required. This trailer hitch is rated up to 7,500 lbs which is the highest available for this vehicle. The max the vehicle can tow is 5,000 lbs so there is no need to go much further over this. In regards to the trailer wiring, I recommend the T-One Vehicle Wiring Harness part # TK22115...
  view full answer...
  
• 7-Way Connector and Brake Controller For a 2021 Ford Bronco Wildtrak Without Tow Package
  Yes, the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter # TK55VR is specifically designed to be used on your 2021 Ford Bronco Wildtrack that did not come with a factory tow package. This kit will allow you to install the Redarc Tow-Pro Elite Brake Controller # RED63RR onto your Bronco and give you a clean factory look. A Mounting Bracket # 18138 will allow you to mount the 7-way connector to a Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR with its mounting...
  view full answer...
• Recommended Trailer Harness Wiring For A 2022 Ford Ranger
  If your 2022 Ford Ranger has the factory tow package then you'll just need the T-One Vehicle Wiring Harness with 7-Way Trailer Connector # 22124. This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located beneath the vehicle, on the driver's side. Once installation is complete, the 7-way connector will be stowed beneath your vehicle, near the trailer hitch. A mounting bracket like # 18138 is recommended to keep the connector secure. If you do not have...
  view full answer...
• Parts Needed To Install 7-Way Connector and Redarc Tow Pro Elite On a 2022 Ford Bronco Badlands
  The Tekonsha OEM Replacement Vehicle Wiring Harness # TK55VR will provide you with the wiring and connector to install a 7-way and brake controller on your 2022 Ford Bronco Badlands with the LED tail lights. The kit includes the wiring and fuses needed to power the trailer lights and the charge line on the 7-way. You will then be able to connect the Redarc Tow-Pro Elite Brake Controller # RED63RR inside your Bronco. This controller includes the wiring adapter to connect to the Tekonsha...
  view full answer...
• Replacement Trailer Hitch Receiver For a 2003 Chevrolet Silverado 1500HD Capable of Towing 12,000LBS
  The Draw-Tite Trailer Hitch Receiver # 41932 checks all the boxes for you on your 2003 Chevrolet Silverado 1500HD. It is a bolt on installation with no drilling required, and has a weight distribution rating of 14,000lbs. The 7-Way # PK11893 can be secured using a Mounting Bracket # 18138. If you prefer to have the strongest receiver available the Curt Trailer Hitch Receiver # C15323 has the highest capacity available. It is rated for up to 2,400lbs of tongue weight and a trailer weight...
  view full answer...
• How to Replace Rusted Trailer Connector Mounting Bracket on a 2007 Chevrolet Avalanche
  In order to replace the rusted trailer connector mounting bracket on the trailer hitch for your 2007 Chevrolet Avalanche I recommend using part # 18144 if you have a 4-way or part # 18138 if you have a 7-way. These brackets will attach to the hitch via the included self tapping screws or by welding. If you do not want to drill into the hitch or weld than you can add the no drill bracket part # 18140 for 4-way or part # C57202 for 7-way in addition to the corresponding bracket listed above.
  view full answer...
• Trailer Wiring and Brake Controller Recommendations for a 2017 Ford Explorer Without OEM Tow Package
  To get your 2017 Ford Explorer (without the factory tow package) fitted with a brake controller I recommend installing the following: Curt T-Connector 7-Way Trailer Connector - # C56306 Mounting Brackets - # 18138 and # C57202 (to secure the 7-Way to your hitch) Curt Echo In-Line Wireless Brake Controller - # C79DR According to my research the wiring for towing a trailer exists whether you have the tow package or not, but to install a brake controller you might need to cut and splice...
  view full answer...
• Wiring for 2013 Mercedes Benz Sprinter to Connect to Trailer's 7-Way
  In order to connect to your trailer's 7 way, you would first need to install the T-One Vehicle Wiring Harness # 118650. This will plug into the wiring harness behind the tail lights on your 2013 Mercedes-Benz Sprinter. From there, you would simply add the Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector # 30717, which would allow you to connect to your trailer's 7-way. I have added a link to an install video for you to take a look at which demonstrates the process. If you needed...
  view full answer...
  
• Is it Normal for 7-Way Bracket of EcoHitch that Fits 2022 Toyota RAV4 to Angle Down
  You did install the 7-way bracket of the EcoHitch part # EH97FR that fits your 2022 Toyota RAV4 correctly. It is an odd angle that the 7-way does hang at. You could maybe try bending the bracket back so that the angle is better or you could use a bracket like the part # 18138 to mount it to the lower bumper at a better angle.
  view full answer...

Do you have a question about this Accessories and Part?