Auto Floor Mats All Weather - Car Truck SUV - Gray

See what our Experts say about this Highland Floor Mats

• Will the Curt Class I Drawbar - 5" Rise Clear My Bumper
  In order to confirm fit of the Curt Class I Drawbar part # C45025 on a vehicle with a recessed trailer hitch you just need to measure from the center of the hitch pin hole to the outer edge of the bumper and make sure it's no more than 8". This one has a 5" rise so the distance from the ground to the top inside edge of the trailer hitch will need to be less than 5" from the distance from the ground to the bottom of the coupler on the trailer. The 2" Hitch Ball part # 19258 is compatible...
  view full answer...
  
• Correct Draw Bar for Curt Class I Receiver C45025 on 2012 VW Golf TDI
  The draw bar included with the hitch is part # C45016, which has a 2-5/8 inch rise, or 3-1/4 inch drop. Ideally, you want to tow the trailer so that it is as level as possible, but being within an inch and a half either way is close enough for government work. Keep in mind that hitch is designed to work best with a draw bar with the same drop as the C45016, and using a draw bar with a different rise or drop is not recommended. I will link you to our FAQ article that shows how to correctly...
  view full answer...
• Ball Mount Recommendation for a 2016 Toyota Corolla with Hidden Hitch
  When picking out a ball mount for a Class I hitch like the part # 60345 you have to go with the ball mount that is recommended for the hitch. If the one that came with this hitch doesn't have the right rise there's nothing I can safely recommend since Draw Tite states that the use of any other ball mount will void the warranty. You will have to use the part # 3593 that came with the hitch in the rise position. This will give you 2-1/8 inches of rise. For a 2 inch ball you would need the...
  view full answer...
• Availability of a Long 1-1/4 inch Ball Mount
  The longest Class I ball mount we offer is the Curt Ball Mount part # C45025 which is 11-6/16 inches long. If you could use a Class II ball mount (also 1-1/4 inch) you could use the Curt Class II Draw Bar part # C45000 that measures 13-1/2 inches from the pin hole to the ball hole.
  view full answer...
• What is the Longest 1-1/4 Hitch Ball Mount You Carry?
  Since you mentioned the Draw-Tite Drawbar - 11-3/4" Long # 36063 and it is only compatible with Class II 1-1/4", it sounds like you have a Class II 1-1/4" hitch. If this is the case, we actually have a longer ball mount available. That is the Curt Class II Drawbar # C45000. This mount measures 13-1/2" from center of hitch pin hole to center of ball hole. If you by chance need a Class I 1-1/4" compatible mount, the longest one we carry is the Curt Class I Drawbar # C45025. This mount measures...
  view full answer...
• Available Drawbars for 1-1/4 Inch Hitches with at Least a 5-inch Rise in the Shank
  The Curt bar # C45028 (5-3/8 inch rise or 6-inch drop) you referenced is one of 3 Curt drawbars we currently offer that will have a 5 inch or more rise in the shank. The reason other shanks may have a different rise is because it may have a different Class rating. I also pulled this drawbar from our warehouse and made a short video and diagram for you. Please note you can only use Class-I rated crossbars because your 1998 Volkswagen Cabrio only works with Class-I hitches. The two other...
  view full answer...
  
• Ball Mount and Trailer Wiring for a 2016 Toyota Corolla with Hidden Hitch Class I Trailer Hitch
  Since you have a Hidden Hitch Class I trailer hitch on your 2016 Toyota Corolla you will need to use a Class I ball mount. Also you have to use the ball mount specified by the hitch manufacturer otherwise it will void the hitch warranty. The correct ball mount for this hitch and vehicle is # 3593 and it must be used in the rise position only. It comes with a hitch pin and clip. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch I recommend # 19258. And for trailer wiring I recommend...
  view full answer...
• Can Curt Class II Ball Mount # C45014 Be Used With Class I Hitch on 2002 Volkswagen Passat
  All hitches offered for your 2002 Volkswagen Passat are of the Class I type and can only be used with compatible Class I accessories. Although the ball mount # C45014 from Curt is also a 1-1/4-inch size it is a Class II ball mount and will not work in your hitch. We do offer two Class I ball mounts with the same 5-inch rise as the part you referenced. These will work in your hitch. You can see both on the link provided; two lengths are available, including the 9-9/16-inch long # C45024...
  view full answer...
• 2 inch Hitch Ball Recommendation to Use with Ball Mounts 3593 and C45025
  For a 2 inch ball to use with the draw bar part # 3593 you would want the part # 19258. For the part # C45025 you would then want the part # C40018. Both balls have 3/4 inch diameter shanks.
  view full answer...
• Recommended Ball Mount To Get 6" Of Rise For a 2015 Chrysler 200 Class I, 1-1/4" Receiver
  Currently our Curt Drawbar # C45028 has the most rise available for a 1-1/4" Class I receiver like that you would have on your 2015 Chrysler 200. The rise is 5-3/8" from the receiver. To get slightly closer to your 6" rise you can use a Curt Class I Drawbar # C45025 with a Curt RockerBall Shock Absorbing 2" Hitch Ball # C94CR. The ball mount has a rise of 5" and the RockerBall sits 1-1/2" higher than a traditional 2" ball. As long as your trailer accepts a 2" ball this would give you...
  view full answer...
• Recommended Drawbar To Tow SeaDoo With 2013 Chevrolet Camaro
  It sounds like you have a pretty good game plan so far! The Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24850 you were looking at is confirmed to fit your 2013 Chevrolet Camaro 2LT and would be prefect for towing your small SeaDoo Trailer. Now the highest rise available in a Class I Drawbar that is long enough to clear the bumper on your Camaro is the Curt Class I Drawbar - 5" Rise - 11-9/16" Long - 2,000 lbs # C45025 that has 5" rise. When we installed...
  view full answer...
• What Trailer Hitch Is Recommended For My 2013 Hyundai Veloster Turbo
  When it comes to installing a trailer hitch on your 2013 Hyundai Veloster Turbo The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4 inch # C11254 is confirmed to fit your vehicle. The hitch can tow up to 1,000 pounds and has a tongue weight up to 100 pounds, so you will not be able to haul your 200+ pound dirt bike, but you could tow the dirt bike on a trailer using The Curt Class I Drawbar - 5 inch Rise - 11-9/16 inch Long - 2,000 pounds # C45025 and attaching The 2 inch Hitch...
  view full answer...
• Parts Needed For Towing a Endeavor Trailer With a 2019 VW Jetta
  Using the Draw-Tite Sportframe Trailer Hitch Receiver # 24978 on your 2019 Volkswagen Jetta the receiver is capable of supporting a trailer up to 2,000lbs with a tongue weight up to 200lbs. You will want to verify towing capability with your owners manual or dealer service department to determine exact capacities for your Jetta. More than likely with Endeavor rating the trailer for a class II receiver is for one of 2 reasons. As they list the dry weight at 530lbs with a load capacity...
  view full answer...
• Ball Mount Recommendation for Class I Draw-Tite Trailer Hitch on a 2005 Honda Accord Coupe
  Take a look at the picture I have included. If the receiver on the Draw-Tite trailer hitch # 24787 on your 2005 Honda Accord has that tab behind the hitch pin hole then the Class II ball mount # C45014 will not fit. But you can use # C45025 which has the same rise and is Class I compatible. Clearing the rear bumper should not be an issue. Ball mount # C45025 measures 11-1/4 inches long from the center of the hitch pin hole to the center of the ball hole. For a compatible 1-7/8 inch ball...
  view full answer...
  
• Selecting Ball Mount for Yakima Trailer with 22" Coupler Height and Ford Focus with 10" Hitch Height
  If you measured a distance of 10 inches from the ground to the top of the inside of the Draw-Tite # 24872 hitch receiver on your 2015 Ford Focus, the Curt Drawbar # C45028 is going to put the ball platform at 15-3/8" above the ground. With the hitch ball actually in place you are looking at a ball height of around 17-3/8", which is still quite below the ideal 22" ball height for the Yakima trailers such as the Rack and Roll # Y08107. With this setup the Yakima trailer is going to be riding...
  view full answer...
• Will a Class II Drawbar Fit Into the Class I Curt Hitch # C11080
  Curt states that Drawbar, # C45522, is the ball mount designed for use with Curt Trailer Hitch Receiver, # C11080. Although the Curt Drawbar, # C45025, will most likely fit in your hitch, it was not designed for use with this particular hitch. If failure occurs when using this drawbar, Curt may void any warranty on the hitch. As for using a Class II drawbar in a Class I trailer hitch, most Class I trailer hitches have a stop built into them so a Class II drawbar can not be used. This...
  view full answer...
• How to Determine the Rise/Drop of Class I Ball Mounts
  There's some specific measurements to take to determine the rise/drop of ball mount you need. Measure from the inside top of the receiver tube to the ground. Then, with the trailer jacked so that it's level, measure the distance from the underside of the coupler to the ground. The difference between the two measurements is the rise/drop needed. If the coupler height is taller than that of the receiver, you'll need a ball mount with a rise. If the coupler height is smaller than that of the...
  view full answer...
  
• Determining Which Drop/Rise Ball Mount will be Needed to Transport my Coleman Popup Camper
  I can help you figure out what which ball mount you will need for your Mazda and Coleman popup camper. There's some specific measurements to take to determine the rise/drop of ball mount you need. Measure from the inside top of the receiver tube to the ground. Then, with the trailer jacked so that it's level, measure the distance from the underside of the coupler to the ground. The difference between the two measurements is the rise/drop needed. If the coupler height is taller than that...
  view full answer...
• What is the Correct Ball Mount for Curt Trailer Hitch C11227 on a 1994 Toyota Celica ST
  This is actually a lot easier to determine than you might think. With any Class I or II trailer hitch you will need to use the ball mount recommended in the hitch instructions. The use of any other ball mount can result in voiding the hitch warranty. The reason is that on Class I and II hitches the ball mount recommended has been tested for and approved for use as the best option for those hitch and vehicle combinations. For trailer hitch # C11227 the recommended ball mount is # C45503....
  view full answer...
• Parts Needed to Tow a Trailer with a 2014 Toyota Prius 4
  As far as whether or not you can tow a trailer with your 2014 Toyota Prius you will need to check the owners manual or with a Toyota dealer for the final say on that. Our understanding is that Toyota says that you cannot tow at all with your vehicle. With that said, we have seen instances where people will do this anyways and parts are available to do so. For a hitch you can use the Curt # C11276, which is a confirmed fit on the 2014 Toyota Prius. For the wiring I recommend using the...
  view full answer...
• Recommended Ball Mount For 2012 Ford Mustang V6 Towing Trailer W/ 17" Coupler Height
  Where we installed the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11210 on a similar 2014 Ford Mustang V6 we found that from the ground to the top inside edge of the receiver measured 10-1/2". As long as the tires on your 19" wheels are the same overall height as the factory tires on your Mustang, this measurement will be the same for your vehicle. I recommend the Curt Class I Drawbar - 5" Rise - 11-9/16" Long - 2,000 lbs # C45025 as this is the most rise available...
  view full answer...
• Recommended Trailer Hitch And Wiring For 2004 Chrysler PT Cruiser
  The trailer wiring is not included with a trailer hitch for your 2004 PT Cruiser. We do offer them separately. There is no drilling required for the installation of the Curt Trailer Hitch, part # C11132. This is a Class l hitch and it has a 1-1/4 inch receiver opening. I have attached a link to an installation video for this hitch on a PT Cruiser you can check out. As the video shows, the trailer hitch uses the tow hook mounting locations on the vehicle frame after they have been removed. The...
  view full answer...
• How To Transport 500lb Medical Scooter With 2010 Honda Accord
  I have another option for you, but there is not a trailer hitch receiver available for your 2010 Honda Accord that can carry a 500lb medical scooter on a hitch mounted carrier. Instead I recommend going with the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11496 you were looking at and getting a small trailer similar to the Detail K2 Mighty Multi Utility Trailer - 6' Long - 1,295 lbs # K2MMT4X6. Since this hitch has a 2000lb trailer weight rating it will be fine for...
  view full answer...
• Utility Trailer, Trailer Hitch Receiver, and Wiring Harness For Towing With 2014 Buick Verano 2.4L
  First you will only be able to tow a trailer if your 2014 Buick Verano has the 2.4L engine and a single exit exhaust. The 2.0L turbo is not rated to tow from Buick and will not fit with Curt Trailer Hitch Receiver # C11282. This receiver paired with a 2.4L single side exhaust will allow you to tow up to 1,000lbs according to your owners manual. The Curt T-Connector Vehicle Wiring Harness # C56288 will give you a 4-way flat trailer connector. This will connect to a Detail K2 Mighty Multi...
  view full answer...

Do you have a question about this Floor Mat?