2000 Dodge Accessories:

change make

Select 2000 Dodge Model



Select Model for Your 2000 Dodge




What our customers are saying:

Excellent customer service. I made an error in my internet order and it was quickly corrected and notified of correction. Order fulfillment was extremely quick and efficient.

James

Somerset, NJ



Accessories



2000 Dodge Questions and Answers


  • How Much Grease To Use when Installing Bearing Buddies on a 1997 Jayco Pop Up Camper
  • Your Bearing Buddy instructions are correct. When installing bearing protectors on a trailer hub, you will want to fill the hub with as much grease as possible, so that you do not have to pump all that grease into the hub with the grease gun after installing the bearings and seals. This also helps to prevent pressure build up in the hub and blow out of the seal in the back of the hub. When using a bearing protector you should always use a double lip seal, like part # RG06-020, which...
    view full answer...

  • How To Determine Which Pin Box I Have and What Replacements Are Available
  • I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the picture that you provided, it looks as though someone may have replaced the original long style pin box with a medium style. In order to determine this you will just need to take a quick measurement from the back row of bolts to the center...
    view full answer...

  • Brake Controller Wire Functions By Wire Color
  • The wires exiting the rear of your controller serve the following functions. The blue wires carries the brake output from the controller, the white wire is the ground, the black wire supplies 12 Volt power, and the red wire is tied into the vehicle brake wiring. If the wiring adapter you have is an aftermarket harness, it should wire up color for color. To the right I have attached a picture of a diagram of how brake controllers wire to tow vehicles. To be safe, I would suggest using...
    view full answer...

  • 7-Way Trailer Wiring for a 2000 Dodge Durango without a Factory Tow Package Connection
  • Since your 2000 Dodge Durango does not have the tow package wiring installed you will need to install a working 4-way connector, # 118334, first and then install a 4-way to 7-way adapter, # 37185. There is not a connection point for the factory replacement connector, # 42145, that you mentioned. If you need to install the 7-Way and need to have functionality for a brake controller and 12 volt power supply for towing you will need additional wiring and circuit breakers. We have an installation...
    view full answer...

  • Availability of an LED Trailer Tail Light Kit that Will Fit a Snowmobile Trailer
  • In terms of a pre-assembled kit with everything included, the closest we have to something with tail lights that are 2-1/2 inches tall would be the Trailer Light Kit with 25 Foot Wiring Harness, # TLL16RK. The included tail lights in this kit are 2-7/8 inches tall. Another option would be to get a couple of # STL76RB lights, and a 4-Way, trailer side wishbone wiring harness, # A35W42B. I have included a link to a video showing the installation of this wiring harness for reference.
    view full answer...

  • Fit of Thule TH898 Hullavator Pro Kayak Carrier w/ Crossbars of Rola Haul Your Might Ladder Rack
  • The kayak carrier is compatible with the Rola ladder rack and you won't need any extra parts.The Thule # TH898 Hullavator Pro Kayak Carrier can either clamp around a crossbar or utilize the T-Slot running across to the top of an Aero-style crossbar. The crossbars used on the Rola # 59742 ladder rack are 4 inches wide, so the clamps won't fit around the crossbar but the Hullavator can mount using the T-slot.
    view full answer...

  • MAP Sensor Wiring Harness and Fuel Injection Pump Location on 2000 Dodge Ram 3500 Diesel
  • If you are using Edge programmer # EP30301 that could be the problem. It is not a fit for a 2000 Dodge Ram 3500. It only fits 2001 to 2002 Rams with the 5.9 liter I6 diesel motor. The one for a 2000 Ram with the 5.9 diesel is # EP30300. On # EP30300 the gray wire with the red connector on it will connect to the fuel injection pump. The round, black connectors go to the map sensor. For the map connection you will need to look for the stock wiring harness at the boost sensor. According...
    view full answer...

  • Tips for Getting a Stuck Gooseneck Hitch Unstuck
  • The first thing you will need to do is apply liberal amounts of spray lubricant to all of the moving parts that seem stuck. Sometimes it helps to apply some, wait an hour or so and apply more and then do whatever it takes to pry the ball out. But it really depends on what style of gooseneck hitch you have. If you have a Fold-Down style like the # 8339-4435 then basically you will just want to do whatever it takes to get the hinged cover to pry up since when it comes up it also moves...
    view full answer...

  • How Would The Westin Sportsman Grille Guard, # 40-0145, Install On My 2000 Dodge Durango
  • This Westin Sportsman Grille Guard, 1-Piece Black Powder Coated, part # 40-0145, would install onto the bumper brace bolts on the outside of the frame on your 2000 Dodge Durango, you will need to be underneath your Durango to access this area. .
    view full answer...

  • Equipment Needed to Flat Tow 2000 Dodge Dakota
  • You will first need a tow bar and base plates. The tow bar will fit into the receiver of the motorhome, and attach to the base plates once they are installed on the Dakota. The Roadmaster Falcon 2, part # RM-520 is a good mid-priced option. Either base plate kit # 246-5 or # 246-6 will work with your Dakota, although the 246-5 is compatible with all the tow bars Roadmaster offers. You will also need safety cables, if you do not already have them. Roadmaster offers a coiled set that works...
    view full answer...

  • Brake Controller Wiring on a 2000 Dodge Dakota
  • You do not mention whether the 7 way is factory installed. If it is, there should be a plug located behind the parking brake pedal. With the Dodge wiring adapter, part # 3020-P you should be able to easily complete your installation. Behind the emergency brake pedal, look for a small white box mounted on the firewall. The connector is typically located just above this box.
    view full answer...

  • Tire Chains for On and Off Road for a 2000 Dodge Ram 2500 with 265/75R16 Tires
  • For diamond pattern tire chains for your 2000 Dodge Ram 2500 and 265/75R16 tires I recommend the Thule XB16 chains # TH01571265. For your tire size this is the only option that has the diamond pattern and can be used on or off road. But if you want something that is going to give you the best grip in snow, ice, and even mud then I recommend the Pewag tire chains # PWE2439S. These chains have large square links which provide the best grip making them ideal for extreme environments. I...
    view full answer...

  • 2-Inch Class III Hitch Receiver Fit on 2000 Dodge Grand Caravan with Rear Sway Bar
  • We do offer two options in a 2-inch Class III hitch receiver for your 2000 Dodge Grand Caravan, Draw-Tite # 75119 and # 37136. Both offer the same capacities and are made by the same company. But since you have the rear stabilizer bar you will use Draw-Tite # 75119. I have linked for you the written instructions for 75119 as well as a video showing installation in a 2003 van. Two helpful hitch installation articles are included as well. If you refer to the linked photo you will see...
    view full answer...

  • How to Add an Additional 7-Way to Existing Factory 7-Way on 2000 Dodge Ram 2500
  • What you will need to do is add an additional 7-Way to your 2000 Dodge Ram 2500 by using the Draw-Tite Custom Fit 90 Degree Vehicle Wiring Harness, part # 51-97-411. This wiring harness will plug in between the OEM wiring harness and your factory installed 7-Way connector and give you an additional 7-Way in the bed of your truck for your camper to plug into. I also have the Draw-Tite Wiring Harness, part # 20111, that will do the same thing as the harness mentioned above. When using...
    view full answer...

  • Why does the Husky Fifth Wheel Rail Kit for a 2000 Dodge Ram Only have 2 L-Brackets
  • The Husky rail kit part # HT31404-686 only includes 2 L-brackets as that is all that is needed to install the kit. If you check out the picture I attached you will see that the rear rail uses the L-brackets and the front attaches to the frame on a long bed truck. For a short bed truck this is reversed.
    view full answer...

  • Recommendation For Fifth Wheel Hitch on 2000 Dodge Dakota V8 to Tow 20 foot Fifth Wheel Camper
  • I would first recommend to make sure and verify that the towing capacity of your 2000 Dodge Dakota V8 Club Cab will be able to tow the weight of the 20 foot fifth wheel camper. The Dakota has a 6-1/2 foot bed so you will need to use a slider hitch to be able to get the needed clearance between the truck cab and the fifth wheel when making sharp turns. I would recommend the Reese 16K Fifth Wheel Hitch, part # RP30075. This is a round tube slider hitch that will have 12 inches of travel...
    view full answer...

  • Is the Thule Goalpost Trailer Hitch Mounted Load Bar Stable to Carry Kayaks on a 2000 Dodge Ram
  • Any time a load extender has height adjustability or a folding feature there is going to be movement. There is no way around it. But there are thing you can do to limit the movement. The Thule Goalpost, # TH997 is going to be your best bet. It is height adjustable from 54-1/2 to 66 inches. It comes with a threaded hitch bolt that will limit movement. To further limit movement at the bottom of the carrier you can use anti-rattle device # RM-061. You would tighten it first and then the...
    view full answer...

  • What Size Cover for 22 to 24 Foot Camper Trailer
  • Camper covers are manufactured to have some wiggle room to make it easier to put on your trailer and to make sure they will accommodate a variety of trailers. Since the frame of your trailer is 24 feet and your camper itself itself is 22 feet, not including tongue, you have found the correct cover, as long as the camper does not hang out over and beyond the tongue Part # 052963733631 is meant for 22 to 24 foot trailers and it should fit just fine on your trailer.
    view full answer...

  • Replacement Roller Fairlead for Badlands 5000-lb Winch
  • All replacement winch fairleads we offer are shown on the linked page. These come from Bulldog, Comeup and Superwinch brands and are application specific for particular winches they make. The nearest size mount we offer to your 6-3/4-inch hole spacing (or 171.4 millimeters) is part # BDW20059 which has mounting hole centers spaced at 165mm (6.49-inches). You may be able to make this item work but for an exact replacement you'll be better off contacting the manufacturer of your Badlands winch.
    view full answer...

  • Custom Heated and Electric Towing Mirrors for a 2000 Dodge Ram 2500
  • For electric operation and heated towing mirrors for a 2000 Dodge Ram you will need # CM-73500. This mirrors fit in place of the factory mirrors and will retain the electric and heat options. If you were to get him these mirrors, you would quite possibly be the best - girlfriend - ever. The mirror you referenced, # KS60113C, will not fit a 2000 Dodge Ram. It fits certain models between 2002 and 2009.
    view full answer...

  • Landing Gear by Atwood Bevel Gear Kit Recommendation that has 12 and 16 Tooth Gears
  • We do have the part you are looking for. On our site it is part # AT75029. This is the gear kit that has the 12 and 16 tooth gear kits like you said you need. The # AT75030 that you also referenced is the correct kit if you have 15 tooth bevel gears.
    view full answer...

  • Replacement Bumper for a 2000 Dodge Dakota Quad Cab
  • We have 2 perfect match bumpers that will fit your 2000 Dodge Dakota Quad Cab as long as it is an R/T, SLT, or base model. For chrome plated steel use # 31012. And for gray powder coat steel use # 32012. The universal bumpers will not fit Quad Cab models.
    view full answer...

  • Replacement Mounting Brackets and Hardware for Westin Tube Steps for a 200 Dodge Ram 2500/3500
  • The hardware kit and brackets you will need are # 25-124PK. They will fit Westin tube steps # 26-1240 as well as # 25-1240 and # 25-1245.
    view full answer...

  • Replacement Bumper Recommendations for 2000 Dodge Dakota Quad Cab SLT
  • The Westin Perfect Match series replacement bumpers will work for your 2000 Dodge Dakota SLT Quad Cab. For a chrome one you would want a # 31012. If you wanted a gray powder coated one you would want a # 32012. My contact at Westin said that the Diamond step bumpers, which are the more universal ones, will not fit the Quad Cab because they come with separate brackets to to mount the bumper that are not compatible with the Quad cab.
    view full answer...

  • Wiring 2000 Dodge Dakota for Brake Controller
  • The 2000 Dodge Dakota will not have the quick connector under the dash for installing a brake controller unless it was factory equipped with the OEM 7-way trailer connector. I am unaware of anything a dealer might offer that would change this. Without the under-dash connector, the brake controller would need to be hardwired into the existing vehicle wiring using our Brake Controller Installation Kit, part # ETBC7. This would be a more involved installation than simply plugging the controller...
    view full answer...

  • Carrying 2 Kayaks and 2 Bikes on 2000 Dodge Ram 1500
  • The easiest way to transport the Kayaks and bikes would be to begin by installing a roof rack on your Ram truck. You'd need the following parts: 58 Inch Round Crossbar, part # Y00409 Yakima Q Tower roof rack feet, part # Y00124 Yakima Q Clips, part # Y00645 (order two of these) With the rack in place, you'd need a kayak carrier. Rhino Rack offers a J style carrier, part # S512 that will allow you to carry an additional kayak with the addition of the # RRS512X Expansion Arm. The...
    view full answer...

  • Will the Black Powder Coated Diamond Plate Bumper # 63000-93800 Fit a 2000 Dodge Dakota
  • The Westin Diamondstep Replacement Bumper with Custom Install Kit, Black Powder Coat, item # 63000-93800, will fit nicely on your 2000 Dodge Dakota as long as your truck is not a Quad Cab (4 Door) model. This bumper is black powder coated with a diamond plate top for sure footing. You do not have to use the higher priced bumpers (see link) unless you want the added features that they offer, like chrome finish, rubber step pads, or OEM design.
    view full answer...

  • Complete Tow Bar System for 2000 Dodge 3/4 Ton
  • My recommendation for towing your 2000 Dodge Ram 3/4 ton 4x4 pickup with a diesel would be the Roadmaster Blackhawk 2 All-Terrain Non-Binding Heavy Duty Tow Bar, 10,000 lbs, part # RM-422, and the Roadmaster MX Base Plate Kit, part # 249-6. This tow bar and base plate kit are especially designed to tow vehicles with heavy duty frames and the tow bar installs easily into a 2 inch receiver hitch. You will need to be careful of the amount of weight you put in the pickup due to the weight...
    view full answer...

  • Ladder Rack and Tonneau Cover that Can be Used Together on a 2000 Dodge Ram Short Bed
  • You will need a tonneau cover that installs on the insides of the bed rails. In other words it cannot rest on top of the bed sides. I have included a link to the tonneau covers we carry that fit this description. Then you will need a ladder rack that does not clamp to the bed sides. There is one option that will work, the TracRac sliding ladder rack # TA21501-02. I have linked a video review of this ladder rack for you. Please note that it is possible that on a ladder rack like this...
    view full answer...

  • Which Westin Sportsman Grille Guard Hardware Fits 2000 Dodge Dakota
  • The Westin Sportsman Grille Guard that would fit a 2000 Dodge Dakota would be the part # 40-0145 which means the correct install hardware would be the part # 40-014PK and not the kit you referenced.
    view full answer...




^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.