1987 GMC Spare Tire Bike Racks

Change Make

Select Vehicle Model

--Select Model-- Jimmy S-15 Jimmy

   Go

Available Models for 1987 GMC Spare Tire Bike Racks

Jimmy

S-15 Jimmy

Accessories

Towing

Trailer Hitch

Trailer Wiring

Brake Controller

Fifth Wheel Hitch

Gooseneck Hitch

Towing Mirrors

Base Plate for Tow Bar

Vehicle Tow Bar Brake System

Vehicle Tow Bar Wiring

Cargo Control

Roof Rack

Tool Box

Ladder Rack

Tailgate

Truck Bed Extender

Trunk Bike Rack

Headache Rack

Truck Bed Sliding Tray

Truck Bed Bike Rack

Spare Tire Bike Racks

Performance Accessories

Air Filter

Suspension Enhancement

Transmission Cooler

Vehicle Lights

Throttle Body Spacer

Vehicle Sway Bars

Catalytic Converters

Vehicle Snow Plows

Vehicle Engine Heaters

Off Road Lights

Radiator Fan

Vehicle Trim

Floor Mats

Tonneau Cover

Nerf Bars - Running Boards

Vehicle Covers

Side Window Vents

Truck Bed Mat

Bumpers

Mud Flaps

Truck Bed Rail Caps

Vehicle Tent

Vehicle Seat Covers

Replacement Mirrors

Windshield Wiper Blades

Wheel Liners

Windshield Covers

Vehicle Air Mattress

Tailgate Lift

1987 GMC Questions and Answers

• Trailer Hitch Recommendation for a 1987 GMC 1500 Pick Up Truck
  
• The Draw-Tite Class III Trailer Hitch, # 75034, will fit your 1987 GMC 1500 as long as it does not have a deep drop bumper. If your truck has an 8 ft bed and a deep drop bumper, then you will need the Draw-Tite Trailer Hitch, # 41504, I have attached a photo of a typical deep drop bumper if you are not familiar with them. If your truck has a 6 ft bed, then you will need additional hardware to complete the installation. You will need six 3/8 inch spacer blocks, # 01077-011, and six carriage...
  view full answer...


• Comparing the Roadmaster Quiet Hitch Ant-Rattle Devices for 2 Inch and 2-1/2 Inch Trailer Hitches
  
• The difference between the Quiet Hitch anti-rattle devices # RM-062 and # RM-061 is what they are made to fit. First, # RM061 is designed for 2 inch trailer hitch receivers. And # RM-062 is designed for 2-1/2 inch receivers. There are some 2 inch receivers that are larger than standard and might require the # RM-062. The outside of a 2 inch receiver should be 2-1/2 inches (not counting the very end which would be larger). A 2-1/2 inch receiver would be 3 inches on the outside. Since...
  view full answer...


• Availability of Gauge/Compressor Kit for Air Lift Ride Control Air Helper Springs # AL59512
  
• First of all, thank you very much for your many purchases from etrailer.com. For your Air Lift Ride Control Air Helper Springs # AL59512 that are in your 1987 GMC C/K Series pickup we can offer you several choices in an in-cab compressor/gauge kit. Air Lift Load Controller # AL25592 is a single-path, single-gauge compressor system that will adjust one pair of springs equally. It detects when air pressure in your helper springs falls below the 5-psi minimum level and restores air spring...
  view full answer...


• Trailer Hitch Recommendation for a 1987 GMC 1/2 Ton Truck
  
• For your 1987 GMC 1/2 ton truck with a short bed and standard bumper the highest capacity trailer hitch we offer is the Draw Tite part # 75034 which has a 500 lb tongue weight rating and a 5,000 lb total trailer weight rating. Since it sounds like you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball,...
  view full answer...


• Troubleshooting Draw-Tite Activator IV Trailer Brake Controller on 1987 GMC Sierra
  
• You will need to test the brake controller wiring using a circuit tester like # 40376. First check and test the connector at the bumper. Next check the red wire connection. It should be attached to the wire on the stop light switch that only has voltage when the brake pedal is pressed. If your red wire is connected to a wire that carries even a few volts when the brake pedal is not pressed, it is not the correct wire. Make sure that the white ground wire is attached to a clean metal...
  view full answer...


• Is there a Custom Fit Trailer Hitch that is Hidden Behind the License Plate on a 1987 GM C/K Series
  
• All of the trailer hitch options for the 1987 GM C and K series trucks will have the receiver placed directly under the rear bumper. There are no custom fit models that will fit behind the license plate. What you could do though is have a professional installer weld on a hitch, # 41990-07. This is actually a Class V hitch but it still has a 2 inch receiver.
  view full answer...