fall hauling headquarters

Claim a 20 Dollar Prpaid Visa Card with Purchase of Curt Front Mount Trailer Hitch

Front Mount Hitch

Change Make

Select Vehicle Model

  
Front Mount Hitch

Available Models for 2003 Toyota Front Mount Hitch


Front Mount Trailer Hitches

Front mount hitches are the perfect addition to your vehicle when you require the use of a recovery winch, tow loop, putting your boat in the water, or other accessory. We offer a large selection of front mount receivers by popular manufacturers like Draw-Tite, Reese and Curt so you can find the one that is right for your application and your budget. All front mount receiver hitches we offer are made in the USA and come with a limited lifetime warranty.

You can find all the custom-fit front mount receiver applications we offer for your vehicle by choosing the year, make, and model to the left. Don't forget the hitch-mounted winch mount plate to make any winch installation hassle-free!





Front Mount Hitch Accessories



Front Hitch Manufacturers

Accessories



2003 Toyota Questions and Answers


  • Choosing a Replacement A-Frame Trailer Jack for Pop-Up Camper
  • I will assume you are looking for an A-frame mounted jack, because that is what pop-ups typically use, and because that is the part you referred to. The bolt hole pattern is standard, so matching up with the holes in the trailer tongue should not be a problem. You would want to choose a jack whose capacity is greater than the tongue weight of the pop-up, which is typically 10-15 percent of the fully loaded trailer weight. The Dutton-Lainson # DL22781 jack you mentioned should have...
    view full answer...

  • Parts Needed for Installation of Electric Brakes on a Coleman Pop-Up Camper With 8 Inch Wheels
  • The 8 inch diameter wheel on your Coleman Fleetwood pop-up camper is not large enough to accept an electric brake hub and drum assembly. Seven inch brake assemblies like # 23-48 that you selected work with the Trailer Hub & Drum Assembly, item # 8-257-5UC3, which will fit in wheels starting at 10 inches in diameter. You would need to upgrade your wheels and tires to either a 5.30-12 load range c wheel and tire combination, or a 205/65-10 load range c wheel and tire to meet the capacity...
    view full answer...

  • Trailer Lights Not Working When the Headlights are Turned On in a 2003 Toyota Camry
  • It sounds like you have a ground issue. When the headlights are on, the highest amperage draw is placed on the wiring system and, a faulty ground will show at this time. Make sure you have good metal to metal contact. Paint and corrosion can act as insulators, so make sure the grounds are touching clean metal. I would check all of the ground connections on the trailer. First, check the ground at the trailer tongue. Take the ground loose and clean the connection point on the trailer...
    view full answer...

  • What Is The Purple Wire Used For On The Brake Controller 7 & 4 Way Installation Kit # ETBC7
  • The purple wire on the adapter included with the Brake Controller 7 & 4 Way Installation Kit, # ETBC7, is an auxiliary wire and can be used as a 12 volt power source, to power a reverse light or reverse lockout function for trailer brakes if needed. This wire can be tied up if it is not used, which is why you often see it left unused in our installation videos. You can see some helpful wiring diagrams at the link provided, as well as a video showing the purple wire on the 4-Way to 7...
    view full answer...

  • Installing a Brake Controller from Scratch on a 2003 Toyota Tacoma
  • To install a brake controller on your 2003 Toyota Tacoma, you will need 3 things. First, you will need a brake controller. There are many to choose from in basically two different categories; time delay and proportional. The biggest difference between the two is that time delay controls will brake the same amount in every braking situation. Proportional controllers brake in proportion to how much the tow vehicle is braking which leads to less brake wear and better braking. I have included...
    view full answer...

  • Troubleshooting a Trailer that Keeps Blowing Left Turn/Brake Lights
  • It sounds like there might be a short on the left turn/brake circuit of your trailer. That would explain why the bulb went out initially and then why it went out again after you changed the bulb. I would inspect the circuit starting at the trailer connector and go all the way back to the tail light looking for corrosion or exposed wire and fix as necessary. The other thing I would check is the ground of the tail light assembly, bad grounds can cause all sorts of bizarre behavior so I...
    view full answer...

  • Trailer Hitch for a 2003 Toyota Tundra with Factory Towable Bumper
  • Yes, you can install Curt trailer hitch # 13184 on your 2003 Toyota Tundra with the factory towable bumper. I have included a link to a video showing an example installation for you. I also recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right...
    view full answer...

  • Locking Hitch Pin Recommendation that Won't Rust
  • It sounds like you are looking for a replacement locking hitch pin since you said the lock pin of your hitch. For a locking hitch pin I would recommend the Bulldog Trailer Hitch Lock part # BD580402 as it is stainless steel which is rustproof.
    view full answer...

  • Does the Use of a Pop Up Camper Cover Trap Moisture and Cause Mold
  • You just have to use the right type of cover to avoid excess moisture build up on the pop up camper. A cover like # CA80042 that you have referenced has integrated air vents. This allows moisture to escape and it also reduces wind stress. I have linked the instructions for you. If you were to seal off the camper with a regular tarp that did not allow moisture to escape you would be looking at a mold problem.
    view full answer...

  • Can the Edge Insight Comprehensive Gauge Display be Switched to Different Vehicles
  • The Edge Insight, # EP84130, will fit in any 1996 and newer vehicle that has an OBD-II port, so you can switch it to a different vehicle. Because this device is a comprehensive gauge display and does not tune the engine, additional programming, other than periodic updates to the software, are not required.
    view full answer...

  • How Do Cold Air Intakes Affect Fuel Economy
  • A cold air intake like the AFE Direct Fit Cold Air Intake System # AFE51-11052 that you referenced could only help your fuel economy. Most likely it would give you a few more miles per gallon. As long as it is installed correctly it should give you increased fuel mileage and performance. I attached installation instructions for you to check out also. When the filter gets dirty you may also be interested in purchasing AFE Filter Cleaner # AFE90-59999
    view full answer...

  • Can a Trailer Axle be Put On a Truck Bed to Make a Trailer
  • First, I am pretty sure you don't have to change the axle out if you are making a trailer out of a truck bed. You will want to check the laws in your state/area though. The highest capacity straight axles that we carry are rated for 3,500 pounds which likely exceeds the capacity of the truck bed. For a trailer axle that will accept a hub with a 6 on 5-1/2 bolt pattern you could use # T3584F-8974 with hub # 84655UC1. Or EZ lube axle # T3584F-EZ-8974 with hub # 84655UC1-EZ. Both of...
    view full answer...

  • Replacement Catalytic Coverter Recommendation for 2003 Toyota Corolla
  • We offer a direct-fit, 49 state legal (except for California) catalytic converter for your Corolla, part # MF93200. The converter you referenced, part # MF36760, is for a Nissan Maxima or Pulsar.
    view full answer...

  • Function of Center Pin on a 7-Way RV Blade Style Trailer Connector on a 2003 Toyota 4Runner
  • No problem, I will be happy to help. The 7-Way you have is called a blade or RV style. The center pin will either be for reverse lights or auxiliary 12 volt power. If the trailer does not have reverse lights or does not need a second 12 volt circuit then it would not matter if the adapter had it or not. If the trailer has an electric reverse lockout feature, common on boat trailers with surge brakes, then you would need that center pin in the adapter and the center pole on the vehicle...
    view full answer...

  • Will The Hidden Hitch # 90638 Clear Spare Tire On 2003 Toyota Sienna
  • Yes, you will be able to access the spare tire with the Draw-Tite # 75120, on your 2003 Toyota Sienna. I contacted our representative at Draw Tite, and he informed me that they have not had any issues with part # 75120, fitting the 2003 Toyota Sienna or clearing the spare tire. He informed me that you may want to lower the spare tire to provide easier access when installing the hitch and then raise it back into place. You should not have any issues with part # 75120 clearing the spare...
    view full answer...

  • Roof Rack Recommendation for a 2016 Jeep Compass
  • For your 2016 Jeep Compass if you have a roof with flush mounted rails you would want the part numbers # RREB137B, # RRRLKVA, # RREB-FK1 and # DK254 to complete a roof rack. For a naked roof you would want the part numbers # Y00409, # Y00124, # Y00699, and # Y00634.
    view full answer...

  • Trailer Brake Lights Not Working when Connected to a 2003 Toyota Tacoma
  • Does your 2003 Toyota Tacoma have a factory tow package and trailer connector? If so then it could be a blown fuse associated with the tow package wiring. Many times, the tow package wiring is separate from the vehicle tail light wiring so the truck brake lights working would make sense. If it is an aftermarket wiring harness such as # 118379 then it is strange that the brake lights on the trailer are not working because the brake lights and turn signals are on the same circuit. This...
    view full answer...

  • Light Kit Recommendation for a Motorcycle Carrier
  • We have a light kit that could possibly be made to work on your motorcycle carrier, part # 98174LED. Without knowing what motorcycle carrier you have it would be hard to say exactly what you would need to do to mount it to your carrier. The lights of this kit are considered submersible meaning they are waterproof. This kit is designed to attach to a 4-way connector, so you would need a 7-way to 4-way adapter to allow you to connect your trailer connector to this light kit. For that you...
    view full answer...

  • What is the Weight Capacity for the Rola Roof Rack part # 59721
  • The 110 weight capacity of the Rola Sport Series Roof Rack # 59721 is the capacity of the pair of cross bars that the roof rack consists of. The capacity is for the two crossbars together. Your canoe that weighs 110 lbs should be fine, on this roof rack. You will want to consult the owners manual of your 2003 Toyota Matrix to determine what the roof capacity is and be sure not to exceed that figure if it is lower than 110 lbs.
    view full answer...

  • Trailer Wiring Harness Converter Box Failed on a 2003 Toyota Tacoma
  • The converter box alone in a trailer wiring harness such as # 118379 for your 2003 Toyota Tacoma cannot be replaced. The whole harness would have to be replaced. Since you have determined that all of the electrical signals going in are correct but not correct on the output side of the converter this does indicate a bad converter. But, if the converter stopped working because of a short somewhere on the trailer you will want to fix the short or the problem will keep happening. Make sure...
    view full answer...

  • Connection Points for Trailer Wiring on a 2003 Toyota Highlander
  • I would be glad to help you out with adding trailer wiring to your 2003 Toyota Highlander. The Tow Ready Harness, # 118413, is designed to plug in line with the tail light wiring behind each tail light on the vehicle. Inside the rear cargo area, behind the tail lights, there are access panels that allow you to get to the tail light wiring connectors. All you have to do is unplug them and plug in the connectors on the wiring harness in line with the vehicle wiring. Ground the white...
    view full answer...

  • Can 50 inch Crossbars be Used on a Thule Roof Rack Instead of 58 inch Bars
  • You should have no problem using the 50 inch Thule Square Bars part # THLB50 on your 2003 Toyota Highlander with raised side rails. The other part you will need is the Thule Crossroad Roof Mounted Roof Railing Foot Pack # TH450. I attached an install video for this rack on a similar Highlander as yours, you'll notice that the crossbars used are 50 inch.
    view full answer...

  • High-Low Adapter Needed for Blue Ox Aladdin Tow Bar
  • From your drawing it looks like you are need to know the distance from the hitch pin hole to the bend on a high-low adapter. For your set-up, you would use the Blue Ox High-Low Adapter, # BX88241, which offers a 7 inch rise. The distance from the hitch pin hole to the bend measures 7-1/2 inches. I have included a picture to illustrate this measurement.
    view full answer...

  • Rivet Size Needed To Install UWS Replacement Locking Paddle Handle # UWSLOCKING
  • The UWS Replacement Locking Paddle, part # UWSLOCKING would use a 3/16 diameter pop rivet.
    view full answer...

  • Can I Flat Tow a 2003 Toyota MR2 Spyder
  • If your 2003 Toyota MR2 Spyder is an automatic it must be towed on a trailer, it cannot be flat towed. If it is a manual, it can be flat towed. You will want to check with your vehicle owner's manual to confirm this. Roadmaster base plates, # 1169-1, are a confirmed fit for your vehicle. If you have a Blue Ox tow bar you can use the adapter # RM-033. To make the draw-bar arms on the base plates removable, use adapter # RM-032. This adapter comes with quick disconnects so you can remove...
    view full answer...

  • Trailer Jack with Wheel Recommendation for a Bear Boat Trailer
  • The Dutton-Lainson Trailer Jack, # DL22300, that you referenced will fit trailer jacks up to 3 inches wide by 5 inches tall with the bolts provided. This jack will be able to fit your 3-1/2 inch wide x 3-1/2 inch tall trailer frame using longer bolts. The mounting bracket on this jack has different holes to accommodate different height trailer frames up to 5 inches. You could also use a weld on style jack like the Fulton Round, Snap-Ring Swivel Jack, # FTJ120W0301. This jack welds on...
    view full answer...

  • Parts Needed to Flat Tow 2003 Toyota Tacoma 4WD Manual Behind Class C Motorhome
  • Flat towing a vehicle behind a motorhome, safely and legally, requires a number of components which include the tow bar, safety cables, a wiring/lighting kit of one type or another, base plates and a braking system for the towed car, and often also a high/low hitch adapter and wiring extension. All of these items are covered in the linked article on flat towing and additional articles on braking systems and high/low adapters are linked too. I also suggest you check your Tacoma owner's manual...
    view full answer...

  • Hitch, Weight Distribution, and Brake Controller Recommendations for a 2003 Toyota Tundra
  • To tow your 2010 Cougar trailer with your 2003 Toyota Tundra, I recommend the Draw-Tite Trailer Hitch, # 75105. This is a Class III, 2 inch hitch with 5,000 pounds gross trailer weight capacity (8,000 with weight distribution) and a tongue weight capacity of 500 pounds. To pull the Cougar trailer, you will need weight distribution. I have included a link to the installation instructions for this hitch below. You might also be interested in a ball mount to pull other trailers, that do...
    view full answer...

  • How to Tap Into 7-Way Reverse Light Circuit to Engage Trailer Coupler Reverse Lockout Solenoid
  • It sounds like your trailer's surge coupler has an electric reverse lockout solenoid feature to disable the brakes when you reverse the trailer. On the Hopkins Adapter # 37185 you will want to connect the Tacoma's reverse light circuit wire to the purple wire. This wire includes a yellow butt connector for making that connection. Please refer to the linked photo. You can either trace the Tacoma's taillight wires to find which one goes to the backup light, or you can use a circuit tester...
    view full answer...

  • Recommended Replacement Trailer Lights and Jack
  • You can remove the snap ring of our Bulldog jack and leave the welded mounting bracket on your trailer. You can replace the jack with # BD151460. The closest LED tail lights we have to yours are # 271595 for the driver's side and # 271594 for the passenger's side. They measure 7-1/2 by 3-1/2 inches with 2 inches between the mounting holes. They're submersible. We don't have the exact clearance light either but # AL91AB is very close and I think will work for you. It's also an LED...
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.