Menu Icon
fall hauling headquarters

Claim a 20 Dollar Prpaid Visa Card with Purchase of Curt Front Mount Trailer Hitch

Front Mount Hitch

Change Make

Select Vehicle Model

  
Front Mount Hitch

Available Models for 1989 Chevrolet Front Mount Hitch


Front Mount Trailer Hitches

Front mount hitches are the perfect addition to your vehicle when you require the use of a recovery winch, tow loop, putting your boat in the water, or other accessory. We offer a large selection of front mount receivers by popular manufacturers like Draw-Tite, Reese and Curt so you can find the one that is right for your application and your budget. All front mount receiver hitches we offer are made in the USA and come with a limited lifetime warranty.

You can find all the custom-fit front mount receiver applications we offer for your vehicle by choosing the year, make, and model to the left. Don't forget the hitch-mounted winch mount plate to make any winch installation hassle-free!





Front Mount Hitch Accessories



Front Hitch Manufacturers

Accessories



1989 Chevrolet Questions and Answers


  • What is the Metric Equivalent Tire Size in a Load Range D For the G78-15 Load Range C Tire
  • The Metric equivalent of the G78-15 load range C trailer tire is a 205/75-15 tire. The 205/75-15 tire is not available in load range D, so you will have to stay with the load range C that you currently have. I would recommend going with a radial tire, for a better ride and increased performance and longevity. You should not experience any more bulge with a radial tire than you do with a bias ply tire so your should not have any clearance concerns as long as you stay within the capacity...
    view full answer...

  • E1 Error Code on a Hopkins Reliance Trailer Brake Controller for a 1989 Chevy 2500
  • The E1 error code on the Reliance brake controller indicates that a trailer is not connected. If the trailer IS connected and you get the E1 code, a probable cause is a dirty trailer connector. Check the trailer connector on the trailer and on the vehicle. Clean out any dirt or corrosion. Corrosion can build up behind the connectors where the wires attach as well. However, the fact that it shows power without braking and then shows less with the override applied indicates that the controller...
    view full answer...

  • Solution for Removing RV Plastic Hub Covers that Attach to Lug Nuts
  • The Wheel Masters Lug Nut Cover Pliers, part # WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.
    view full answer...

  • Can Bully Bumper Mount Backup Light # PL-807 Directly Plug In to Flat 4-Pole Trailer Connector
  • The Bully Bumper Mount Backup Light # PL-807 is designed for hard-wired installation by connecting to the reverse light circuit of your Chevrolet pickup. It is not intended to connect to a 4-pole or 5-pole flat trailer connector. Installation is simple. You will connect the black (ground) wire to a clean bare metal surface on the vehicle or you can use an existing grounding point behind one of the tail light assemblies if one is available. The fused (red) power input wire will splice...
    view full answer...

  • Trailer Hitch Receiver Compatible With 1989 Chevy G30 RV On Cutaway Van Frame
  • For your 1989 Chevy Van Cutaway, I recommend the Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2" # 41121. If this will not fit with the waste water tank, then I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. If these brackets won't fit, you will need to make a completely custom hitch made by a professional welder. If this is the case, they often like beginning with the Combo Bar 12" with 2" Trailer Hitch Receiver...
    view full answer...

  • What is a Roll Ban Bumper when Looking at Trailer Hitch Fits for a 1989 Chevy S-10
  • If you take a look at the picture I have included the truck in it has a type of roll pan bumper. Essentially it is a bumper that matches the contours of the vehicle instead of protruding out like a regular step bumper. If your 1989 Chevy S-10 has a regular bumper then you can use Curt hitch # C13021. If it has a roll pan bumper then use # 13920. If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2...
    view full answer...

  • Wheel Lock And Coupler Lock Recommendation For Trailer To Deter Thieves
  • The best wheel lock system we offer is the Lock'em Magnum Wheel Lock, part # RA-25. This system will work on 12 to 17 inch wheels. One side works on 12-15 inch wheels and the other side works on 15-17 inch wheels. The arms measure 1 inch X 7/8 inch at the narrowest point and would be extremely difficult to cut off with a bolt cutter. For added security, you may want to check out part # DT25013KA. This is a coupler lock that will work on 1-7/8 inch , 2 inch, and 2-5/16 inch couplers....
    view full answer...

  • Fit of Longview Towing Mirror # LVT-1000 on 1989 Chevy Suburban
  • Longview tells me that the # LVT-1000 mirror will fit all models of the 1989 Suburban. If you look at the photo I have edited for you, you can see a photo of the OE mirror that the # LVT-1000 designed to fit on.
    view full answer...

  • How Can Offset be Determined for Trailer Tires on a Trailer
  • I do have a solution for you but we don't recommend using a spacer as that will cause your wheel to sit at a different location on your lugs. The offset of a wheel can be determined by measuring from the mounting surface of the wheel (where it mounts to your hub) to the inside and outside beads once the wheel has been removed from your trailer. The difference of these measurements tells you what your offset is. Most trailer tires have an offset of zero but if your wheel has a negative...
    view full answer...

  • Recommended Trailer Hitch Receiver for a 1989 Chevy K1500 Sportside Pickup
  • The best way to tell if your 1989 Chevrolet K1500 is a Heavy-Duty (HD) or Light-Duty (LD) version would be to obtain your VIN and call the dealer as they would be able to tell you whether or not you have the HD or LD version. Another way to tell if your truck is an HD or LD would be to look at the gross vehicle weight rating (GVWR). If the GVWR of your truck is 5,600 lbs then you have the LD version but if your GVWR is 6,100 lbs then you have the HD version. This information can generally...
    view full answer...

  • Availability of a Trailer Hitch for a 1989 Chevrolet R3500 Cab and Chassis Truck with Dump Box
  • According to my technical contact at Draw-Tite your 1989 Chevrolet R3500 cab-and-chassis with dump box has no direct-fit bolt on hitches available. However, there may be an option in a universal-fit weld on Class V hitch. Curt offers a universal-fit weld-on Class V hitch with 2-inch receiver opening an 3-inches of drop, part # 15901. This hitch fits truck frame widths between 18-inches and 43.88 inches. Installation requires welding on the side brackets to the main tube and welding...
    view full answer...

  • Recommended Radiator Fan 1989 Chevy Camaro
  • The best radiator fan for your 1989 Chevrolet Camaro would be the largest on you have space available for behind the radiator in front of the engine. With that being said, Derale has several electric fan options that will do a great job of keeping the 400 small block engine cool. I recommend the Derale High-Output, Electric Radiator Fan-and-Shroud Assembly part # D16928. The overall dimensions of the fan assembly are 28-5/8" wide x 13-7/8" tall x 3-1/4" deep. The fan assembly will take...
    view full answer...

  • Front Mount Trailer Hitch for a 1989 Chevy C2500 Pickup Truck
  • We do have some front mount hitches that fit a 1989 Chevy C2500 pickup but # 65005 only fits the 4-wheel drive models. For a 2-wheel drive we have # 65021. It fits as long as the truck is not a crew cab model and as long as it has 8-lug wheels. We also have Curt front hitch # 31043. It will fit as long as you do not have a cab and chassis model which has a frame width of 34 inches measured from the outside of one frame rail to the outside of the other. I have included links to the...
    view full answer...

  • Hitch Recommendation for a 1989 Chevrolet Caprice Estate Wagon
  • The Draw-Tite Hitch # 41105 that you referenced is discontinued, but was listed to fit a 1977 to 1990 Chevy Caprice Estate wagon. The current Draw-Tite hitch for your 1989 Chevy Caprice Estate Wagon would be the Draw-Tite Class II 1-1/4 Inch Hitch, part # 36105. I attached installation instructions for you to check out. If you plan on doing some towing you may be interested in the following products to complete your towing setup: Trailer Wiring # 18252 (installation video attached) Class...
    view full answer...

  • Will Draw-Tite Front Mount Hitch Receiver # 65005 Fit 1989 Blazer K-5 4WD
  • The Draw-Tite Front Mount Hitch Receiver, part # 65005, will fit the full-size Chevrolet Blazer for model years 1992 through 1994. It will not fit your 1989 Blazer. There is currently no front-mount hitch receiver available for your vehicle. I confirmed this with my technical contact at Draw-Tite. We do offer a rear hitch receiver for your 1989 Blazer, the Draw-Tite Class III 2-Inch hitch, part # 75129. This rear hitch is rated for 500-lbs tongue weight, and is also rated for use with...
    view full answer...

  • What Parts are Needed to Flat Tow a 1989 Chevy Astro 2 Wheel Drive Automatic
  • I have done a little research and have found that your 1989 Chevy Astro can be flat towed, but it does require a transmission lube pump. A company called Remco makes the part you will need. To verify this, you can consult the vehicle owners manual to determine the proper procedures for flat towing your van. In addition to a pump, some vehicles must be equipped with an axle disconnect, drive line disconnect, or free-wheeling hubs before they can be towed. In order to flat tow, you will...
    view full answer...

  • B&W Gooseneck Hitch Recommendation for a 1989 Chevrolet 3500 K Series Long Bed Pickup
  • For your 1989 Chevrolet 3500 K series truck you will want the B & W Gooseneck # BWGNRK1000, which has mounting hardware specifically designed for your truck. I have added a link that shows all of the gooseneck hitches available for the 1989 Chevrolet C/K Series Pickup. We also have an informational article on gooseneck hitches that you may find helpful.
    view full answer...

  • Class III Hitch That Fits 1989 Chevy Silverado 1500 Standard Cab
  • Would you be able to tell me if you have a Crew Cab on your Silverado? Also, do you know what kind of bumper you have? Standard, Step, Roll Pan, Deep Drop. I also assume your truck is 4WD but want to confirm that as well. If you can get back to me with this information I may be able to find you something that works.
    view full answer...

  • Functions of Three Prongs on Tow Ready Battery Isolation Solenoid
  • The two side prongs on the Tow Ready Battery Isolation Solenoid # TR118665, and likely your solenoid, are for voltage in and out to your auxiliary battery and the center connection is to the ignition power source, so it sounds like you have guessed correctly. If you take a look at the accompanying photo of Solenoid # TR118665 it shows this. Keep in mind that a solenoid is only designed to provide a maintenance charge so you do not drain the battery on your '89 Chevy conversion van....
    view full answer...

  • Availability of Window Vent Shades for a 1989 Chevrolet S-10 Blazer 2 Door
  • Yes, we do have window vent shades or window air deflectors for the 1989 Chevrolet S-10 Blazer 2 Door. I have the Weather Tech Side Window Air Deflectors, part # WT70152. The Weather Tech air deflector will install in the window channel and has a light tint. I like the Weather Tech deflectors because they are a thicker material and the installation is clean and simple. I am including a link to the installation instructions on the Weather Tech deflectors.
    view full answer...

  • Fit of Cipa # CM10200 Slide On Towing Mirrors on 1989 Chevy K2500 Truck
  • The Cipa # CM10200 slide-on towing mirrors are designed to fit stock mirrors that are shown in the photo I provided. If your mirrors aren't like what's shown in the photo, they will not fit. What exactly is the fit issue? Do the mirrors just not fit over the existing mirrors?
    view full answer...

  • 5th Wheel Installation Kit for RBW Lil Rocker and 1989 Chevy K2500 Pickup Truck
  • I agree with you 100 percent. Better safe than sorry especially considering the size and type of load being carried. For your 1989 Chevy K2500 you can use the Reese universal installation kit # RP30035 as long as the truck is not a Crew Cab model. The RBW Lil Rocker should fit the Reese rails. To be sure you can compare the measurements of the mounting feet on the hitch with the picture I have provided of the rails just to be on the safe side. For in-bed wiring it will depend on...
    view full answer...

  • What is the Inside Width of Replacement Jack Handle # DL22674 where it Attaches to the Trailer Jack
  • I went out to the warehouse and pulled a Replacement handle, # DL22674, to measure it for you. Where the handle bolts to the jack, the inside width is 1/2 inch. I have included a link to a video review featuring this handle for you.
    view full answer...

  • Stake Pocket Tie-Down Anchor T55Z Dimensions
  • The actual outside dimensions of the stake pocket anchors part # T55Z that you referenced where it slides into the stake pocket is the exact dimensions you listed. 3-1/2 inch by 1-1/2 inch. I attached a picture that has these dimensions listed.
    view full answer...

  • Can Base Plates And Front Hitch Be Installed At The Same Time On 1989 Chevrolet K1500 Pickup
  • The mounting holes used to install the Curt Front Hitch, part # 31042 on your 1989 Chevrolet K1500 truck are the same hole needed for the installation of the Roadmaster Base Plates, part # 131-8. You would not be able to have both installed at the same time because of this interference. I have attached the installation instructions for both the 31042 and the 131-8 you can check out.
    view full answer...

  • Brake Controller Light Flashes when Trailer is Connected to a 1989 Chevy C/K 2500 Pickup Truck
  • It sounds like either the white ground wire is not properly connected or is not connected to the best ground location or there is a short to the blue wire. First, make sure you have the white ground wire attached to the negative battery terminal. This is the best ground location for a brake controller. No other ground locations will really work as well. To test the controller, in the truck cab you will need to sever the blue wire several inches from the back of the controller. Then...
    view full answer...

  • Connecting Red Brake Controller Wire to Cold Side of Brake Switch on a 1989 Chevy C/K Series Truck
  • It is possible that the wire you need on the brake switch is a white wire on your 1989 Chevy truck. But the only way to know for sure is to test all of the brake switch wires. If you are unable to find the correct wire at the brake switch then it might be possible to use the CHMSL fuse and a fuse tap. This would only work if the CHMSL fuse is just for the center high mount stop lamp. If it is the fuse for other functions as well then it would not work. Other than the brake switch and...
    view full answer...

  • Trailer Hitch for a 1989 Chevy R3500 Dually Crew Cab with 8 Foot Bed a 34 Inch Frame Width
  • If your 1989 Chevy truck is a cab and chassis model (these are the ones that come without beds that are then turned into service vehicles, flat beds, and that sort of thing) then hitch # 41947 will fit for sure. But apparently, for 1989, Chevy trucks with a long bed and crew cab had a 34 inch frame width. So in this generation of GM trucks there are some pickup models that have the 34 inch frame. I also recommend etrailer ball mount kit # EBMK2416 which comes with a ball mount with a...
    view full answer...

  • Trailer Hitch and Wiring for a 1989 Chevy K3500 with 10 Inch Deep Drop Bumper
  • Draw-Tite trailer hitch # 41528 does indeed fit your 1989 Chevy K3500 truck with deep drop bumper. It is rated for 6,000 pounds gross trailer weight when not using weight distribution. If you want a hitch that has a little more wiggle room in terms of capacity you can use # C15317 which is rated for 16,000 pounds when not using weight distribution. Be sure to check the capacity of your truck and go by whichever has the lower capacity; the hitch or the truck. If you go with hitch #...
    view full answer...

  • Replacement Hitch Install Hardware for Draw-Tite Class III Hitch # 75129
  • We sure do. Use part number RHK by clicking on the provided link. On the product page, type in '75129' for the hitch item number and choose Draw-Tite from the drop down menu. I've linked you to the installation instructions for the # 75129, in case you no longer have them.
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.