Menu Icon
fall hauling headquarters

Save Up To 10 Percent Off on Storage and Security Products

Battery Box Relocation

Change Make

Select Vehicle Model

  
Battery Box Relocation

Available Models for 2010 Ram Battery Box Relocation



What our customers are saying:

The people answering the phones were professional & knowledgeable. All this and the best prices on the internet, How can you go wrong?

Bill

Vero Beach, FL



Accessories



2010 Ram Questions and Answers


  • Bully Dog Tuner vs. Others for Use in 2010 Ram 2500 With 5.7L V8 Hemi Gasoline Engine
  • The link provided will take you to our page for all tuner/monitors that are compatible with your truck. The options vary in terms of their potential power/torque gains and also in their 50-state compatibility; some of the tuners shown are not legal for use in California. Note the particular Bully Dog tuner you referenced, the Triple Dog GT BY40410NI, is intended for Nissan/Infiniti vehicles and will not work for your 2010 Ram 2500 with 5.7L Hemi engine. The tuner you can install is the...
    view full answer...

  • Where is Brake Controller Install Harness in 2010 Ram 1500 with 7-Way
  • Since your 2010 Ram 1500 has a round 7-way connector at the rear of it that means a brake controller like our best selling Prodigy P3 part # 90195 could easily install with the correct harness, part # 3021-P. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. I attached a picture that points out where it will be as well.
    view full answer...

  • Sidewinder Pin Box Replacement Recommendation for a Lippert 1621 Pin Box
  • If you have a Lippert 1621 pin box the # RP61420 that you referenced would work for you, but not the # RP61410 as it is designed to fit a different style pin box. I attached an install video for the # RP61420 for you to check out though, it would work well with your Draw Tite fifth wheel hitch as well.
    view full answer...

  • Using the Tailgate EasyLift with the EZ Down Tailgate Lowering System on a 2010 Dodge Ram 1500
  • The designs of the Hopkins EasyLift, part # 74211, and the DeeZee EZ Down Lowering System, part # DZ43300 allows these two products to be installed on your 2010 Dodge Ram 1500 without interfering with each other. Our contact at DeeZee stated these two products should work together, however, they have not been tested together so it is not guaranteed.
    view full answer...

  • Best Gooseneck Hitch Recommendation for a 2010 Dodge Ram 2500 Short Bed
  • The most popular gooseneck hitch we offer with other owners of 2010 Ram 2500s with 6 foot beds is the Draw-Tite Gooseneck # 9464-35. This is a great hitch that would be strong, safe and about as easy as a gooseneck hitch can be to install. I attached installation instructions and an install video for you to check out for more info. Since you have a short bed you may also want the gooseneck ball with offset part # 19308 to give you better clearance while turning.
    view full answer...

  • Recommended Trailer Hitch Receiver for 2010 Dodge Ram 1500
  • Curt Manufacturing offers a few different high quality, made in America hitches for your 2010 Dodge Ram 1500. The right hitch for you will depend on what you'll be towing and how much it weighs. If a 6000 lb towing/ 600 lb tongue weight (maximum amount of weight that can safely be suspended from the hitch) will work for you, you can't go wrong with the Curt Class III hitch, part # 13333. For a higher capacity, 10000 lbs towing/1000 lbs tongue weight, go with the Curt Class IV, part...
    view full answer...

  • Front Axle Jounce Spring Kit for 2010 Ram 2500 4x4 Using Front-Mounted Hitch, Plow and Cargo Carrier
  • We have just the kit you need for your 2010 Ram 2500's front axle to support your front-hitch-mounted cargo carrier and snow plow loads. The Air Lift AirCell Custom Helper Spring Kit # AL52211 is a confirmed fit on your Ram 2500 4x4. This jounce spring kit installs easily (no drilling and no air lines!) and requires no maintenance at all once installed. These microcellular urethane springs provide progressive resistance to match the load placed on them. They will stiffen and support...
    view full answer...

  • Will Titan BrakeRite SD Adapter for Ford/Chevy Brake Controllers # T4845900 Work on 2010 Dodge 3500
  • The Titan BrakeRite SD Adapter for Ford/Chevy Brake Controllers # T4845900 that you referenced is intended for use with Ford and Chevy OEM brake controllers but not those supplied by Dodge. It is quite common for our customers to choose to replace their OEM brake controller with an aftermarket unit such as the popular Tekonsha Prodigy P2 # 90885. Typically the performance and broad compatibility of this and similar controllers (that work well with both electric and EOH brakes) make them...
    view full answer...

  • Recommended Fifth Wheel Installation Kit For 2010 Dodge Ram 2500 With Or Without Overload Springs
  • You can tell if you have overload springs easily. Just take a look at your rear leaf springs, and if you see an extra leaf as shown in the attached drawing you have the overload spring option. The Reese Fifth Wheel Hitch, part # RP30047, will work with your 2010 Dodge Ram 2500. The difference would be in the installation kit. The custom installation kit like part # RP50140-58 will not work with gas engines and overload springs. If you find you do not have the overload springs, then this...
    view full answer...

  • Installing Tekonsha Prodigy P3 Brake Controller on 2010 Ram 1500 with Factory Brake Controller
  • The Tekonsha Prodigy P3 # 90195 Trailer Brake Controller is an excellent choice and the Plug-In Adapter # 3021-P is exactly what you need to install it on your 2010 Ram 1500. When you remove the factory brake controller on your Ram, it will activate a warning lamp on your instrument cluster. The only way to prevent or get rid of this light is to visit a local Ram dealer to have them reconfigure the TIPM (Totally Integrated Power Module) of the truck. You will want to wait until this...
    view full answer...

  • Trailer Lighting Options for 1962 Airstream Undergoing Renovation
  • The vehicle-to-vehicle taillight converter part # 118158 will do what you want: separate the Ram's combined stop/turn signals into separate signals that can be fed to separate stop and turn lights on your vintage Airstream. This converter will not work with a vehicle that has LED lights but it WILL work on a trailer that has this high-efficiency type lighting. Vehicles with LED lights use much lower power signals along with lighter-gauge wiring that would not be able to operate the...
    view full answer...

  • Can a 2010 Dodge Ram 1500 Tow a Trailer with a Golf Cart
  • Well since the bumper says a maximum of 500 lbs of tongue you should go with that as the maximum tongue weight. There should also be a total trailer weight rating as well. Typically the tongue weight rating of a hitch or vehicle is 10 percent of the total trailer so in your case it most likely is 5,000 lbs. However, most towing bumpers will have a capacity of 3,500 lbs. You will want to verify this. The owners manual of your vehicle should have this information as well. You will want...
    view full answer...

  • Troubleshooting Valley Phantom Brake Controller
  • Valley is no longer in business so there is nothing specific in regards to that brake controller we can offer. There is some troubleshooting you can do. Start by severing the blue wire a couple inches from the back of your controller. Then use a circuit tester such as # 40376 to test the end of the blue wire coming out of the controller. It should only have power when you apply the manual override; if it shows power at idle then there is an issue with the controller and it will need to...
    view full answer...

  • Trailer Hitch to Tow 5th Wheel Trailer w/1 Long Bed Ram or 1 Short Bed Ram with Gooseneck Hitches
  • The only part of this that really complicates things is that the 2010 Ram 2500 is a short bed. Otherwise the Demco Recon # DM8550045 would be the ideal solution. Do you happen to know the brand of gooseneck hitch in your 1999 Ram 2500? If it happens to be a B&W gooseneck hitch then you could use the Companion slider # BWRVK3400 and you'd just need to put a B&W gooseneck hitch in the 2010 Ram using # BWGNRK1313. The short bed truck is going to require a slider hitch in order for you to...
    view full answer...

  • Recommendation to Extend Factory 7-Way to Fit with New Bumper on 2010 Ram 2500
  • There are a couple of options to extend the factory wiring at the rear of your 2010 Ram 2500 so that it can reach the new connecter opening on the 2015 bumper. The easiest solution is to use a 5th Wheel Wiring Harness like the Curt # C56070. This will plug in-line with your existing factory wiring and provide an extended harness on the other end. The only drawback on this option is that the Curt # C56070 represents the shortest 5th Wheel Harness that we offer at 7 feet long. So you will...
    view full answer...

  • Recommended Autoslide Hitch for 2010 Ram 2500 Mega Cab
  • Though an auto-slide hitch is not going to give you more front-to-back travel, it is extremely beneficial because of how simple it is to use and I highly recommend the auto-sliding Demco Hijacker # DM8550037 for your 2010 Ram 2500 Mega Cab. You can mount this hitch with the Underbed Rail and Installation Kit # DM8551005, which is a confirmed fit for your truck and has underbed rails so you can remove the hitch at any time and still have full access to your truck's bed. The Hijacker uas...
    view full answer...

  • Parts Needed to Install Curt e16 Fifth Wheel Trailer Hitch
  • Since you have the universal brackets you will need to drill into the frame of your truck. I've attached the installation details for the Husky universal brackets # HT31563 for you. On page 7, it states to use the adapter kit # HT30665 for Dodge 1500 2009-2014. I've also attached an install video on a 2006 Dodge. The bracket kit is not the same because we used a custom kit, but some of the measurements will be, so the video might be helpful to you.
    view full answer...

  • Air-Lift Compressor Install Location on a 2010 Ram 2500
  • My Air Lift rep has the same exact compressor kit on his truck (# AL25870), and he installed his compressor on the inboard side of the truck frame under the cab. If you have a 2 wheel drive 2010 Ram 2500 you would want the # AL88297 and for the 4 wheel drive model part # AL88295. Either kit will have more than enough air line for the job as this kit was designed specifically to fit your vehicle. To protect the lines you could use wire loom like part # 459075-1 sold by the foot.
    view full answer...

  • Will the X-Treme Gate Truck Bed Extender # XG-001 Rattle In the Wind While Travelling
  • The X-Treme Gate Truck Bed Extender # XG-001 is not going to rattle on your tailgate while you are travelling down the highway. The clearances on the hinges and moving parts of this product are tight enough that it would not move around and/or rattle.
    view full answer...

  • Is the Reese Elite Series 5th Wheel Hitch Compatible with a Revolution Pin Box and 2010 Ram 2500
  • Yes, the Reese Revolution pin box and the Reese Elite Series 5th wheel hitches such as # RP30142 are compatible with each other. You will just need the appropriate custom wedge # SWW-01. Since you are using a Revolution pin box I recommend using the fixed version of the Elite hitch # RP30142 because the pin box is not meant to be used with a slider hitch. For an installation kit that will fit your 2010 Ram 2500 and the Elite hitch I recommend # RP30852 which is the custom fit below...
    view full answer...

  • Ladder Rack for a 2010 Ram 1500 that Will Allow Tonneau Cover to Install
  • The key to picking out a ladder rack for a truck so that you can also install a tonneau cover is to go with one that installs through the top of the stake pockets in the bed rails so that a tonneau can fit between them. Instead of the K2 you would need something like the TracRac part # TH43003XT-000 if you have an 8 foot bed or the part # TH43003XT-501 for if you have a 6 foot bed. These will allow the install of a tonneau like the # TX546901 for if you have a 6 foot bed or part # TX548901...
    view full answer...

  • 5th Wheel Installation Kit for a 2010 Ram 2500 and Pro Series 15K 5th Wheel Hitch
  • For your 2010 Ram 2500 and Pro Series 15K 5th wheel hitch you can use Curt custom installation kit # C16420-204. It fits both short and long bed versions of the 2010 Ram 2500. I have included a link to a video showing an example installation of this kit for you. You might also be interested in adding a 7-Way trailer connector # C56000 in the bed of the truck. This will make connecting the trailer easier without the need of any sort of extension. I have linked a video on the wiring as well.
    view full answer...

  • Rear View Camera Recommendation for Mounting On Back of Camper that Tows Trailer
  • The Rear View Safety Wireless Camera part # RVS-155W that you referenced would be an excellent option for you as it has a 70 foot interference free range and 18 LED diodes for night vision as well. It also has a 130 degree viewing angle as well.
    view full answer...

  • Reese Fifth Wheel Bracket Kit Recommendation for 2010 Ram 2500
  • The Reese bracket kit you need is # RP50140 as the part number you mentioned fits newer trucks and not your 2010 model. You will also need the hardware kit part # RP58430 to connect the rails to the brackets.
    view full answer...

  • Recommended Firestone Air Springs for 2013 Ram 3500 Crew Cab with Leaf Springs
  • If your 2013 Ram 3500 Crew Cab is 4 wheel drive, then the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs # F2705 are a confirmed fit as are # F2560. If you have a 2 wheel drive model, then you will want the Firestone Ride-Rite Air Helper Springs - Double Convoluted # F2579 springs instead. They will work with your leaf spring suspension perfectly as you can see in the installation video and the installation details. Air springs # F2701 will not fit your vehicle. I...
    view full answer...

  • Availability of B&W Universal 5th Wheel Base Rails for a 2010 Ram 2500
  • If you already have the B&W Custom Mounting Brackets # BWRVR2600 and all of the hardware for your 2010 Ram 2500 then the B&W Universal Base Rails you need are part # BWRVR3210. These 2 kits makeup the whole custom kit # BWRVK2600 for your pickup. Please note that if you have used hardware it will need to be replaced as well since it is only meant to be torqued to specs once. If you don't already have a 7-Way connector in the bed of your Ram then I also recommend installing the part...
    view full answer...

  • Can I Use Curt Trailer Hitch Receiver # C15409 Same Time as the OEM Hitch on 2010 Dodge Ram 3500
  • The hitch you have referenced, Curt Class V Trailer Hitch Receiver, part # C15809, is a 2-1/2 inch receiver, and can be installed along with an OEM receiver, on your 2010 Dodge Ram 3500. The towing capacity for this hitch is 20000 lbs, and it also has a tongue weight capacity of 2700 lbs. For this receiver I would recommend the Reese Ball mount, Part # RP45322. It has a towing capacity of 18000 lbs. I would also recommend Hitch ball, part # 63840, which has a towing capacity of 20000...
    view full answer...

  • Gooseneck to Fifth Wheel Adapter for 2010 Ram 3500
  • There is a way for you to tow a fifth wheel trailer with a gooseneck hitch but the Curt Q25 # C16265 you referenced is not compatible with the Draw-Tite gooseneck hitch in your 2010 Ram 3500. If that hitch is the Hide-A-Goose # 9464-57 you could use the Draw-Tite Hi-Rise Gooseneck-to-5th-Wheel Trailer Hitch Adapter # 9480. This hitch has a capacity of 18,000 lbs along with a 9" king pin funnel width. I've added a link to a video review of this product for you to take a look at as well.
    view full answer...

  • B and W Companion Hitch Recommendation for a 2010 Ram 1500 Short Bed
  • The B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter # BWRVK3400 that you referenced would be exactly what you would need. This would install in the bed of your 2010 Ram 1500 that has a B and W Turnover Ball gooseneck hitch installed and would let you tow your fifth wheel trailer. This hitch also has a slider so that you can make tight turns with your short bed truck. I attached a review video for this hitch for you to check out as well. If your brother has a B and W Turnover...
    view full answer...

  • Underbed Installation Brackets for Gooseneck Hitch On 2010 Ram 2500
  • In order to find the underbed installation brackets compatible with the overbed gooseneck hitch you have, we will need to know the manufacturer of the gooseneck. If the gooseneck you removed from another truck is either the Curt Folding Ball # C-52 or Flat Plate gooseneck hitch # C65500, you can use the Curt Custom Installation Kit for Curt Overbed, Folding Ball Gooseneck Trailer Hitch # C61529. If your exisiting gooseneck is not a Curt hitch, I will be happy to find the correct...
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.