fall hauling headquarters

Fifth Wheel Hitch

Change Make

Select Vehicle Model

  
Fifth Wheel Hitch

Available Models for 2009 Toyota Fifth Wheel Hitch


5th Wheel Hitch with Custom Installation Kit

Big trucks require big hitches! We offer high quality Reese, B&W, Draw-Tite, Husky, Demco and Curt fifth wheel hitches that are the perfect fit for your heavy duty towing needs. From standard 5th wheel hitches to slider systems for short bed trucks, we have an application for you. From our Pro Series fifth wheel to Reese's top-of-the-line Signature Series, you can find the perfect fifth wheel for your payload while staying within your budget.

We offer custom rail kits for many of the most popular vehicles including Ford, Chevrolet, Dodge, GMC, and Toyota. Choose a Signature Series hitch and rails to retain full use of your truck bed while not towing. Find the custom installation kit for your vehicle by entering the year, make, and model to the left.

Add a fifth wheel lube plate, pull pin lock plates, and in-bed wiring to round out your fifth wheel towing setup.





Fifth Wheel Hitch Accessories



Fifth Wheel Hitch Manufacturers



Accessories



2009 Toyota Questions and Answers


  • Is an Aftermarket Trailer Hitch and Wiring Harness Different than an OEM Trailer Hitch and Harness
  • You will often pay inflated prices at car dealers. There is really no difference between the trailer hitch and wiring harness that Toyota offers for your 2009 Toyota Venza than the Curt Trailer Hitch, # 13356, and the Curt Trailer Wiring Harness, # C56079. All trailer hitches must pass specific tests whether they are OEM or aftermarket. In fact, Curt is in the OEM market as well as the aftermarket. Curt manufactures trailer hitches for a few different vehicle manufacturers. All of their...
    view full answer...

  • Why are Transmission Coolers Installed on the Fluid Return Line After the Radiator Mounted Cooler
  • The biggest reason that transmission cooler manufacturers and vehicle manufacturers want transmission coolers installed after the factory cooler rather than before it is because the transmission cooler in the radiator is surrounded by the coolant in the radiator. The transmission fluid leaving the radiator mounted cooler can be cooled further by the aftermarket transmission cooler. Installation before the OEM radiator mounted transmission fluid cooler would negate most or all of the...
    view full answer...

  • Comparison of Round Bar and Trunnion Weight Distribution System For a 2009 Toyota Tundra Crew Max
  • The difference between the # RP66088 and the # RP66084 weight distribution systems is the style of spring bar attachment. The # RP66088 system has round bar style spring bars, these spring bars are a bit harder to install and hang a bit lower, closer to the ground, than the Trunnion style spring bars. This system is a bit more economical than the Trunnion style system and would work great for your vehicle and trailer. The # RP66084 system has the Trunnion style spring bars, that traditionally...
    view full answer...

  • Will Yakima SkyBox 16 Cargo Box # Y07335 Fit a 2009 Toyota Prius and Clear the Rear Hatch
  • To determine if the Yakima SkyBox 16 Cargo Box, part # Y07335, will fit the roof of your 2009 Toyota Prius and clear the rear hatch you will need to take a measurement on your vehicle's roof. The minimum clearance measurement to determine rear hatch clearance is taken from the center of the front crossbar of the roof rack on your vehicle to the seam of the rear hatch on your Prius. That measurement will need to be 52 inches or more for the roof cargo box to clear the rear hatch on your...
    view full answer...

  • How to Adjust Weight Distribution System for Level Towing
  • Don't worry, I can help explain how you will need to adjust your weight distribution system for the best tension. First thing to know is that there is no particular set amount of bar tension that is standard for all vehicles. It will depend on the vehicle and the trailer and how its loaded. Ultimately you will want to check your Tacoma's wheel wells for the best fitment. When you have the proper amount of tension for your setup your front and rear wheel well will measure the same...
    view full answer...

  • How Does Thule Hullavator Kayak Carrier Install on Thule Aeroblade Crossbars
  • We don't have a video that shows the Thule Hullavator # TH898 being installed on a set of Thule Aeroblade crossbars but I can describe to you the process. I also attached pictures that I took from the install instructions that show how it attaches as well. Basically you would remove the wind diffuser on the top of the Aeroblade bar so that you could cut out sections for the install of the square nut that installs in the channel that provides the attachment point for the rack. (see the...
    view full answer...

  • Location of Brake Controller Factory Port on 2009 Toyota Tacoma
  • If your 2009 Toyota Tacoma has the factory 7-Way connector at the rear of your vehicle the factory brake controller port is located underneath and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 5-pin connector that mates with the one on the Tekonsha # 3040-P adapter. I am including a picture that will show the brake controller factory plug location. If your Tacoma does not have the factory 7-Way connector, the vehicle will not have...
    view full answer...

  • Trailer Brakes Instantly Apply When Trailer is Plugged Into Tow Vehicle
  • Are you sure that the horse trailer has a 5-Way connector, and not a 6-Way such as part # 30205? In any event, I do not believe this is a problem with your brake controller. I would bet that the adapter or the trailer is wired incorrectly. When the adapter is plugged in, the pin for the trailer brakes is contacting the pin for the 12 volt accessory lead on the 7-Way connector on your Tacoma. As soon as the trailer is plugged in, the brakes instantly receive 12 Volts, and lock up. There...
    view full answer...

  • Replacement Step Pads For Nerf Bars 21x3 Inches With 4 Posts
  • We do have a 21x3 inch replacement pad. It is the Replacement Step Pad for Westin E-Series Nerf Bars - 21" Long x 3" Wide - Qty 1, # 23-0001. Unfortunately this pad has 5 posts. The closest 4 post replacement pad we have is the Replacement Step Pad for Westin Platinum Series Nerf Bars - 20" Long - Qty 1, # 26-0001.
    view full answer...

  • Availability of TracRac Ladder Rack for 2009 Toyota Tacoma Regular Cab
  • For your 2009 Toyota Tacoma regular cab you will need to use either the TracRac Pro2 Truck Bed Ladder Rack, part # TH37004XT or the TracRac TracONE Truck Bed Ladder Rack, part # TH27000XT-EX. These will be a correct fit for your vehicle. These are both a fixed mount ladder rack. To install the # TH27000XT-EX ladder rack to a Toyota Tacoma you will also need the TracRac Mount Kit, part # TH34000. See included link for the instructions on the mount kit. I am including links to the installation...
    view full answer...

  • How to Add Taillights on Thule T2 Bike Rack That Blocks Taillights of 2009 Toyota Sienna
  • Although it's intended for a cargo carrier, we have a light kit that work great for you. Part # 98174LED provides long lasting LED lamps that use minimal power but are very bright. You'll also need two brackets for the lamps, part # BK70BB. The brackets could be mounted to the underside of the rack using bolts or even zip ties if the idea of drilling holes in your bike rack doesn't thrill you. Another option would be magnetic tow lamps like # RM-2120 that could be installed on top of...
    view full answer...

  • Where Does a Stabilizing Strap Attach for a Cargo Carrier and CURT Trailer Hitch, 2009 Toyota Prius
  • CURT Class I, II, and some Class III trailer hitches do require the use of stabilizing strap # 18050 on all non-trailer loads to be in compliance with the CURT warranty. A non-trailer load would include a cargo carrier, so you would need to use the strap. One end of the strap would be secured to the cargo carrier, the other end has a rubber coated hook. This hook can be placed in the gap between the trunk lid or hatch and the body of the vehicle on a Toyota Prius. The purpose of the...
    view full answer...

  • Malfunction Camper Shell Third Brake light with 4-Pole Wiring Harness on a 2009 Toyota Tacoma
  • If you connected the cab stop light to the wires that go after the converter box to the 4-pole connector, that is why you are having a problem. The signal for that wire is going to a trailer light that does not have separate turn and stop bulbs, so your camper shell is getting both brake and turn signals. You will need to find a dedicated stop light wire in the tail light wiring harness on the Tacoma to activate the third brake light on your Leer cap. You may be able to use the red wire...
    view full answer...

  • Recommended Cargo Carrier with High Ground Clearance
  • The Surco 24 by 60 Cargo Carrier, part # 52018 has a straight shank, which means that the height at the back end would be the same at the height of the receiver. For the Toyota Venza, once a hitch is installed, the top of the receiver would fall just below the bottom of the rear fascia. Depending on the height from the ground to the bottom of a hitch receiver on your vehicle, this might present a problem. If you are concerned about ground clearance, you could use the Pro Series 24 by...
    view full answer...

  • Recommended Weight Distribution/Sway Control for Forest River R-Pod 179 Hood River Edition
  • The key to choosing the right weight distribution/sway control (WD/SC) system is knowing your trailer's actual fully-loaded road-ready tongue weight (TW). We offer a simple-to-use scale # 5780 but other methods for measuring TW are noted in the linked article. To your measured trailer TW you will add the weight of anything in the back of the Tacoma that sits behind the rear axle, say a loaded cooler or generator. With this total effective TW known you can choose the right system. Ideally...
    view full answer...

  • Recommended Trailer Hitch for a 2009 Toyota Matrix XRS
  • The Curt Class-II hitch # C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite # 24812 is a Class-I hitch where as the Curt # 12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But keep in mind the maximum towing weight capacity of your 2009 Toyota Matrix is 1,500 pounds per the Toyota Matrix owners manual. Per Curt instructions, the fascia might have to be trimmed on models with lower fascia but I pulled the Curt hitch...
    view full answer...

  • Gas Water Heater Replacement With Gas/Electric Water Heater
  • Your 1994 Coachman 248TB's factory Atwood G6A-7e is 16" W x 12-1/2" H x 18"D. You can replace it with the gas/electric unit like the manual pilot # AT96117 or the Automatic pilot # AT96163. Both of these units will be the same size, so you will just need to add the electric which will require installing a # 10-2-1 wire to your circuit breaker in the 120V power panel.
    view full answer...

  • Brake Controller Recommendation for 2009 Toyota Tundra
  • For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well. Then to install it in your 2009 Toyota...
    view full answer...

  • Can CE Smith Boat Trailer # CE48810 Be Adapted With a Folding Coupler to Simplify Storage in Garage
  • We offer hinged trailer couplers such as the Fulton Fold-Away Coupler Hinge Kit for 2 x 3-Inch Trailer Tongues, part # FHDPB230101. This particular folding coupler fits 2 x 3-inch steel trailer tongues such as the tongue on the CE Smith Trailer. My contact at CE Smith confirmed that cutting the trailer tongue to install a hinged coupler is perfectly acceptable. This Fulton coupler is rated for 5000-lbs so it is more than adequate for the task on the CE Smith trailer that carries your...
    view full answer...

  • Dimensions of the Hopkins Endurance 7-Way Trailer Connector Socket # HM48480
  • The Hopkins Endurance 7-Way Trailer Connector Socket, # HM48480, measures 2-3/4 inches wide and 3 inches tall. I have attached a picture to illustrate these measurements as well as the distance between the mounting holes.
    view full answer...

  • Hitch Ball Recommendation for a 2009 Toyota Tacoma on the Factory Bumper
  • Since the bumper thickness on your vehicle is 1-1/2 inches I would recommend you get a Hitch Ball with 2 inch Diameter and Long Shank, part # 63849. This # 63849 is designed for drawbars and bumpers that are between 1 inch and 2 inches thick. The Hitch Ball with 2 inch Diameter and Medium Shank, part # 63845, that you referenced is designed for drawbars and bumpers that are from 1/2 inch to 1 inch in thickness. I attached an FAQ article on hitch balls below for you to check out also.
    view full answer...

  • What Is the Installation Like for Timbren Springs on a Toyota Tacoma
  • The install for the Timbren Rubber Enhancement Springs, part # TTORTUN4L, is fairly easy, just one bolt and nut to install the spring and bracket. It bolts in the same location as the factory bump stop. You will just need to jack under the frame of the truck to relieve the tension on the suspension. Remove the bump stop, 1 bolt and nut, and finally install the Timbren spring again with 1 nut and bolt. Repeat on the other side. I have included a link to the directions. I have added links...
    view full answer...

  • Will 29 Inch Trek and Specialized MYKA Fit Thule Spare Me Bike Rack without Adapters
  • I looked at some images of both bikes and as long as they are not full suspension bikes you can load them on the Thule Spare Me, # TH963PRO, without using adapter bars. But they will be carried on the rack at an angle which could affect ground clearance. If either bike has full suspension or you want them as straight as possible I recommend using bike adapter bar # 64005. This will allow you to carry those bikes more level and will provide better ground clearance. I have to use these...
    view full answer...

  • Clearing the Spare Tire on a 2009 Toyota RAV4 with a 24x60 Curt Trailer Hitch Receiver Cargo Carrier
  • The Curt 24x60 Cargo Carrier, part # C18153 will fit the rear of your 2009 RAV4 with spare tire. The distance from the hitch pin hole to the nearest part of the carrier is 9 inches, and this clears the RAV4's available space. If you'd like to verify this distance and fit, you'll want to measure from the center of your receiver's hitch pin hole to the furthest point of the vehicle's spare tire. My research shows that this distance is usually about 6-7 inches. I've included a video...
    view full answer...

  • Replacement 7-Way Trailer Connector for 2009 Toyota Tacoma with Factory Tow Package
  • The Replacement Multi-Tow 7-Way & 4 Pole Trailer Connector, # 74682, was designed to replace the factory 7-way on your 2009 Toyota Tacoma. Just unplug the connector from the back of your current 7-way and plug it into the back of the replacement connector.
    view full answer...

  • Will Hollywood Racks Over the Top 3 Bike Carrier Fit 2009 Toyota Highlander and 2013 Audi A4 Sedan
  • Yes, the Hollywood Racks Over-the-Top 3 Bike Carrier, # HRF2-3, is listed to fit your 2009 Toyota Highlander as well as your 2013 Audi A4 sedan. Prior to mounting the bike rack to the vehicle, you will want to make sure that the surfaces on the car and rack are clean and free of debris to prevent scratching the paint. A good coat of quality car wax applied to the vehicles finish will also provide extra protection. If you will be carrying any women's, children's or alternative frame...
    view full answer...

  • Options for Carrying Two Hobie Kayaks with a 2009 Toyota Venza
  • I may have a solution that will allow you to load your Hobie Pro Angler 14 kayak on the roof rack of your 2009 Toyota Venza, but before you select a kayak carrier for your vehicle, I strongly recommend checking the weight capacity of your vehicles roof. The weight capacity of most vehicle roofs is not very high and this information should be located in your owners manual. It is likely that you will not be able to safely load both kayaks on your roof due to the weight of both kayaks....
    view full answer...

  • Hub Assembly Recommendation for a 3500 lb EZ Lube Spindle
  • The Dexter Trailer Hub and Drum Assembly, # 84546UC3-EZ, that you referenced will fit on a Dexter 3,500 lb EZ Lube spindle, however, this hub and drum assembly was designed to be used with axles that have 10 inch x 2-1/4 inch brake assemblies already mounted. If you do not have brakes, then I would recommend looking into a idler hub like the Dexter Trailer Hub Assembly, # 84545UC1-EZ. This assembly will also fit on the Dexter 3,500 lb EZ Lube spindle and has the same bolt pattern as...
    view full answer...

  • Differences Between Curt # 13323 and Draw-Tite # 75236 Class III Hitches for 2009 Toyota Tacoma
  • The Curt # 13323 and the Draw-Tite # 75236 Class III hitches share the same weight capacity and installation procedure. The appearance and design of the two hitches are pretty similar. As far as quality goes, both brands are about equal. Given this, there's no reason why you couldn't go with the less expensive Curt model. If you were planning on towing with your Tacoma, you might also need the following: Trailer wiring harness, part # 118496 Ball mount, part # 2923 1-7/8 inch trailer...
    view full answer...

  • Tekonsha Prodigy RF Brake Controller Does Not Power On
  • The Tekonsha Prodigy RF, # 90250, gets its power from the vehicle side 7-Way 12 volt pin. If that pin is not working then the unit will not power on. Disconnect it from your 2009 Toyota Tundra and then use a circuit tester such as # 3808 to test the 12 volt pin on the 7-Way. It is in the 1 oclock position if looking at the pins. If there is no power on the pin when the truck is turned on or running then that would be why the unit is not powering on. You will need to check the truck owners...
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.