Tube Steps - Running Boards Installation And Review Videos


DeeZee Round Nerf Bars Installation - 2005 Chevrolet Silverado- Video

DeeZee Round Nerf Bars Installation - 2005 Chevrolet Silverado

Today on our 2005 Chevrolet Silverado, we're going to show you Dee Zee Nerf Bars, part number DZ371523. We've got them installed on our passenger side of our truck, so let's go ahead and cover some of the features. First off, this is a polished stainless steel finish. The diameter of the tube is going to be about three inches. You can see it has a 90 degree turn, and this is inaudible 00:00:23 bent, which means that the tube has a smooth bend all the way around. No kinks or anything like that. The step plates here are constructed from the heavy duty plastic, one half for our extended cab here and of course, the other one for the front of our cab. more


Watch Video

4/10/2015 1:37:51 PM



Pilot Nerf Bars with Installation Kit Installation - 2001 Dodge Ram Pickup- Video

Pilot Nerf Bars with Installation Kit Installation - 2001 Dodge Ram Pickup

Today on our 2001 Dodge Ram Pickup 1500 Quad Cab, we're going to be installing the Pilot Black Powder Coated Nerf Bars, part number NB-1203B. Here's what our tube steps look like installed on our vehicle. Now we'll go ahead and show you how much easier it is to get in and out of your vehicle using the tube steps. Now let's go ahead and begin our installation. We're going to begin our installation over here on the passenger side. Let's first point out our mounting locations that we'll be using for our new tube steps. This front body mount is the front mount location here on the passenger side. more


Watch Video

11/19/2014 7:46:59 AM



Pilot Bully Nerf Bars Installation - 2014 Ram 1500- Video

Pilot Bully Nerf Bars Installation - 2014 Ram 1500

All right, today on this 2014 RAM 1500, we're going to install part number NB-1215x. This is the Bully Nerf Bars, Polished Stainless Steel in 3-inch Diameter. To start off our install, we're going to have all parts laid out. It makes it a little easier to install our nerf bars. I'm going to start on the passenger's side on the front, and our brackets are labeleed, passenger front. We got our hardware together like the instructions will state. more


Watch Video

9/2/2014 2:13:33 AM



DeeZee Rough Step Steel Running Boards Installation - 2013 Ford Van- Video

DeeZee Rough Step Steel Running Boards Installation - 2013 Ford Van

Today on our 2013 Ford Van E-350, we're going to install running boards and DZ, part number DZ2544. The first step is to go ahead and start working on our end caps for our running boards. We'll go ahead and pre-assemble the end cap, which is a small, channel shaped piece of metal with holes on one side. Then we're going to loosely attach a strap bracket. It's basically a flat piece of steel of the same length with the same matching holes. Well go ahead and loosely install them together using a quarter inch bolt, two flat washers and a nut. With these parts loose, we'll go ahead and install it on the end of the running board. more


Watch Video

7/10/2014 3:59:30 AM



Putco Box Board Running Boards Installation - 2005 Ford F-350- Video

Putco Box Board Running Boards Installation - 2005 Ford F-350

Today on our 2005 Ford F350 Super Duty well be installing the Putco Master Boss rounded running board, box board, part number P62522. Note, on this application well need to trim the rear edge in order for it to fit properly with the dual rear wheel setup on this vehicle. First well go ahead and take a straight edge, mark the line and then cut off the top edge. Now with that done were ready to go ahead and install the front end cap. This will be a black cap secured with two cap screws and a quarter inch flange nut. Then well move to the rear flap, or cap, which will be a large polished sheet of steel that well need to remove the protective film from. more


Watch Video

12/20/2012 2:50:12 PM



Putco Running Boards Installation - 2005 Ford F-350- Video

Putco Running Boards Installation - 2005 Ford F-350

Today on our 2005 Ford F350 Super Duty well be installing the Putco Master Boss round running board, part number P62135. First before we install the running boards well need to do some preassembly. Well go ahead and take the drivers side running board, sit it out on a flat surface and install the front cap, or fender flare. Well use the cap screws and flange nuts to secure it. Then well move to the rear of the running board and install the rear cap. Again well use the cap screws and flange nuts to secure it. more


Watch Video

12/20/2012 2:49:56 PM



DeeZee Tube Step Installation - 2012 Dodge Ram- Video

DeeZee Tube Step Installation - 2012 Dodge Ram

Today on our 2012 Dodge Ram pickup, well be installing the DeeZee 5 Oval Nerf Bars, part number DZ17532. Starting here behind the drivers front tire underneath the vehicle well need to remove the tape covering up the oblong hole just above the two premade holes, this will expose the 3 attachment points for our front bracket. Now before we can attach the bracket well take the Nutsert and insert them into the rocker panel. Then well take the Nutsert set tool, thread it into the nutsert holding the nut of the nutserts set tool with a 15 mm wrench and tightening down the bolt of the Nutsert set tool with a 13 mm socket causing the nutsert to wedge into the premade hole. When tightening down the Nutsert set tool well torque them to 25 to 30 foot pounds, this will allow you to know that the nutsert has expanded and is set in the rocker panel. Now once the torque specifications well go ahead and remove the Nutsert set tool and move onto the next nutsert. more


Watch Video

9/7/2012 5:11:08 AM



DeeZee Running Board Installation - 2007 Chevrolet Express Van- Video

DeeZee Running Board Installation - 2007 Chevrolet Express Van

Today on our 2007 Chevy Express Van, were going to install the Deezee Running Boards, part number DZ1030. Our first step is to take the full length of the bright thread and install a foam backing to the upper lip. This lip will be coming in contact with the painted surface on the vehicle. Well go ahead and take our foam padding supplied with our install kit and start on one edge, peeling away the protective cover and working it all the way to the other end. Once we get to the end, lets go ahead and take a razor blade or utility knife, or even a pair of scissors at work and cut off the excess. Now on either end, were going to go ahead and take the mud flap and attach it to the bright thread using the provided hardware. more


Watch Video

4/17/2012 11:21:10 AM



Pilot Tube Step Installation - 2010 Chevrolet Silverado- Video

Pilot Tube Step Installation - 2010 Chevrolet Silverado

Today on this 2010 Chevy Silverado, were gonna install part number NB-1109x from Pilot.Our attachment points are on the body bolts on this vehicle and there are three of them as theyre shown here.Next step is well go ahead and layout our parts. We have a short bracket that goes on the front and then the long bracket that stays in the center and then a tall bracket that goes in the back.So well go ahead and loosen up the body bolts. You want to do this by hand first because some of the models have a thread locker on there and an air ratchet could break the nut inside the body. When we take the bolts out, you wanna prepare the stock bolts to the bolts that come with the kit. Some models have a thicker bolt. If thats the case, go ahead and use the factory bolts. more


Watch Video

11/30/2011 4:32:45 AM



Pilot Automotive Nerf Bar Installation - 2001 Chevy Silverado 1500- Video

Pilot Automotive Nerf Bar Installation - 2001 Chevy Silverado 1500

Today, on this 2001 Chevy Silverado 1500 series regular cab, we will be installing the Bully Nerf Bars part number NB-103. Just rearward of the front tire here, we have the forward body mounting bracket here. As you can see we have a bolt in there. We are going to be taking that bolt out, putting in new hardware. And that is going to provide our forward attaching point for our Nerf Bar. And you will notice that the bushing is coming out as well, with the bolt. And that is okay, but we are going to be putting this bushing back up into place when we get our brackets set up. If we go a little bit further back, just about even with the edge of the door, we have a second body mounting bracket, again with the same bolt. Again, we are going to remove this one as well and get the new bracket and hardware in place as well. 0:52 more


Watch Video

1/28/2010 12:40:19 AM



Pilot Automotive Nerf Bar Installation - 1999 GMC Sierra- Video

Pilot Automotive Nerf Bar Installation - 1999 GMC Sierra

Today we are going to be installing Bully step bars, part number NB-103 on a 1999 GMC Sierra regular cab. We are underneath the vehicle now, and we are going to go ahead and point out the mounting location for the step bars. We are going to locate the body mounting brackets. There is one here at the forward side and one here, more toward the rear, almost even with the edge of the door. These are the two components that we are going to be using to attach our hardware to mount these step boards. We are going to be removing the bolts from these brackets and putting up our mounting brackets for the step bars. more


Watch Video

5/21/2009 6:06:13 AM



  1