Exhaust Systems Installation And Review Videos


MagnaFlow Pro Series Filter-Back Exhaust System Installation - 2016 Ram 2500- Video

MagnaFlow Pro Series Filter-Back Exhaust System Installation - 2016 Ram 2500

Today, in our 2016 Ram 2500, we'll be installing the Magnaflow Pro Series Filter Back Exhaust System for diesel engines, part number MF18912. Here's what our exhaust system looks like installed. This is a complete system, all the way from the diesel exhaust filter, all the way back to our 6 inch polished tip. This exhaust is constructed of an aluminized steel construction, so will provide us with many years of rust resistant service. Not only does it improve the looks of our truck, but it will help improve fuel economy a little bit, give us a little bit more power, and give us a more aggressive exhaust node. Here's what our exhaust system consists of. All of our piping that we have here today is a 5 inch diameter pipe. more


Watch Video

12/19/2016 9:34:50 AM



MagnaFlow Turndown Cat-Back Exhaust Installation - 2013 Ram 1500- Video

MagnaFlow Turndown Cat-Back Exhaust Installation - 2013 Ram 1500

Today on our 2013 Ram 1500, we're going to be taking a look at and installing the MagnaFlow Turndown Cat-Back Exhaust System, part number MF17108. Now, what's really nice about this that's going to set it apart from some of the others on the market, these are designed to work with your lifted or lowered vehicles, especially ones with airbags where your exhaust is going to be a concern coming up over our axle and going close to our airbags. It's all stainless steel, 100% stainless steel, and it's got mandrel bends. The mandrel bend means it's going to stay the same size all the way through the bend, not crushing down and interfering with your exhaust flow. Now, one thing you might want to note, you want to check your state's laws for exhaust because this one does drop out in front of our rear end. In some states it's required that it goes past the rear axle, so you want to make sure that it's actually allowed in your state. With the free-flowing exhaust it's going to help with our torque and horsepower and help with our fuel efficiency. Now, you can see our new MagnaFlow exhaust is considerably smaller than our factory one. more


Watch Video

10/24/2016 2:26:09 PM



Camco Gen-Turi RV Generator Exhaust System Review- Video

Camco Gen-Turi RV Generator Exhaust System Review

Today we'll taking a look at and showing you how to install the Camco Gen-Turi RV Generator Exhaust System. Part number CAM44461. The Camco Gen-Turi RV Generator Exhaust System cuts down on noise and lifts harmful fumes up away from the fun. First let's listen to our RV's generator without the Gen-Turi installed. Oh, that smells so bad. Okay. more


Watch Video

11/4/2015 8:56:06 AM



MagnaFlow Turbo Back Exhaust System Installation - 2003 Ford F-250- Video

MagnaFlow Turbo Back Exhaust System Installation - 2003 Ford F-250

All right, today on this 2003 Ford F250 Super Duty Super Cab, we're going to show you part number MF18985. This is a MagnaFlow Custom Series Turbo Back Exhaust System constructed from aluminized steel. This is basically a steel exhaust with a protective aluminum coating on top of it. All right, this is what the exhaust looks like once installed on the truck. Right off the bat, we can see that we have it routed towards the right-hand side of a truck, and we have a diameter of 4 inches. It is a steel construction with an aluminum coating on the outside and on the inside of the pipe. It uses 1/2-inch thick rods welded to the pipe here, and it goes up to the factory rubber hangers on the truck. more


Watch Video

3/27/2015 10:00:03 AM



MagnaFlow Stainless Steel Cat-Back Exhaust System Installation - 2006 Ford F-150- Video

MagnaFlow Stainless Steel Cat-Back Exhaust System Installation - 2006 Ford F-150

Today on our 2006 Ford F-150 we'll be installing the MagnaFlow Stainless Steel Cat-Back Exhaust System part number MF16616. To begin our install, we'll first need to remove the old or manufacturer's exhaust. Starting at the clamp just behind the Y pipe of the exhaust, we're going to spray it down with some spray lubricant. Note over time this clamp will rust up and can be extremely difficult to get off. In severe cases it may even break. If that happens, it'll be necessary to replace it. In an event where it's so rusted that you can't get a wrench or socket to hold, we'll use a pair of vise grips to try and break it free. more


Watch Video

10/7/2014 2:12:35 PM



MagnaFlow Cat-Back Exhaust System Installation - 2012 Jeep Grand Cherokee- Video

MagnaFlow Cat-Back Exhaust System Installation - 2012 Jeep Grand Cherokee

Today, on our 2012 Jeep Grand Cherokee, we'll be installing the Magna Flow Cat Back Exhaust System, Part Number MF16991. To begin our install, we'll first need to remove the older manufacturer's exhaust. Starting here at the rear of the vehicle, we're going to spray the two rubber isolators, forward and back of the muffler. I'll also go ahead and spray the spring nuts that hold the rear section of the exhaust to the forward section of the exhaust at the exhaust flanges. By spraying the rubber isolators with some spray lubricant, it'll make it easier to remove. We're going to use a pry bar, pliers or, if you have an exhaust hanger removal tool. Starting at the back, we'll begin removing the rubber isolators, noting that on the rear hangers, there's also a metal ground strap. more


Watch Video

9/4/2014 3:32:59 PM



MagnaFlow Performance Stainless Steel Exhaust System Installation - 2007 Dodge Ram Pickup- Video

MagnaFlow Performance Stainless Steel Exhaust System Installation - 2007 Dodge Ram Pickup

Today on this 2007 Dodge Ram Pickup, 2500 Series, Mega Cab, we're going to install part number MF16973. This is the MagnaFlow Performance Stainless Steel Filter Back Exhaust system. Before we get started, we'll go ahead and listen to the sound of our truck so we can compare to it afterwards. Before we begin our install, we'll go ahead and lay out our pieces to get an idea how everything will fit together. First off we have our muffler which we still have in our protective coating while we install it and we'll just hold it up underneath there and get an idea of how it aligns with the factory hangers. Now optionally, this is the straight pipe that eliminates the muffler. Typically, you would use this in off-road applications or racing applications. Now this piece goes over top of the axle. more


Watch Video

7/25/2014 2:33:51 PM



Camco Gen-Turi RV Generator Exhaust System Manufacturer Review- Video

Camco Gen-Turi RV Generator Exhaust System Manufacturer Review

Joe: Hi. My name is Joe with Camco Manufacturing. Today I would like to talk to you about the Gen-turi Generator Exhaust System. As an Rv-er, you will rely on your generator when there is no power hookup available, but along with the convenience comes undesirable noise and exhaust fumes. Running your Rvs generator produces harmful and potentially deadly carbon monoxide. During Rv rallies and times when there is a large concentration of Rvs, what we call dry camping, exhaust can become on even greater problem, concentrated carbon monoxide can spread up to 15' from the exhaust pipe. more


Watch Video

6/30/2014 4:14:39 PM



MagnaFlow Cat-Back Exhaust System Installation - 2012 Toyota 4Runner- Video

MagnaFlow Cat-Back Exhaust System Installation - 2012 Toyota 4Runner

Today on our 2012 Toyota Forerunner well be installing the MagnaFlow Cat-Back Exhaust System, part number MF15145. Before we install the new MagnaFlow system were going to go ahead and test the old or manufacturer system. Well get an idea of what the exhaust sounds like under a load. Now weve installed our new MagnaFlow system and well go ahead and repeat the same process of putting it under load to see what the new exhaust system will sound like. To begin our install well first need to remove the old or manufacturer system. To make it easier to remove the system well go ahead and spray down the exhaust flange bolts with some spray lubricant. This will make it easier to remove later. more


Watch Video

6/19/2014 4:04:19 PM



MagnaFlow Stainless Steel Cat-Back Exhaust Installation - 2006 Chevrolet Trailblazer- Video

MagnaFlow Stainless Steel Cat-Back Exhaust Installation - 2006 Chevrolet Trailblazer

Today on our 2006 Chevy Trailblazer, well be installing the MagnaFlow Exhaust System Part Number MF16656. To begin our install, well first need to go ahead and remove the old or manufacturers exhaust system. To remove it, were going to go ahead and cut it into a couple of pieces. Using a reciprocating saw, well cut just in front of the rear muffler and then just behind the front muffler. Now with our exhaust system cut in 3 pieces well need to remove the 3 fasteners that secure the front flex pipe flange to the muffler exhaust pipe flange. Note I recommend to spray these with some liquid penetrant because over time theyll build up with rust, dust, dirt and debris, and can be very difficult to remove. more


Watch Video

9/4/2013 4:11:11 PM



MagnaFlow Rockcrawler Cat-Bat Exhaust System Manufacturer Review - Jeep Wrangler- Video

MagnaFlow Rockcrawler Cat-Bat Exhaust System Manufacturer Review - Jeep Wrangler

Thanks for your time today. This is Richard of MagnaFlow and today were going to be installing one of our jeep exhaust systems. We have a variety of different systems out there. Were going to be putting one of our high clearance Jeep Rockcrawler Systems on. Take a closer look. The first step of an installation is installing the inlet pipe. more


Watch Video

8/15/2013 8:20:34 AM



MagnaFlow Cat-Back Exhaust System Installation - 2003 Chevrolet Tahoe- Video

MagnaFlow Cat-Back Exhaust System Installation - 2003 Chevrolet Tahoe

Today on our 2003 Chevy Tahoe, we'll be installing the MagnaFlow stainless steel cat-back exhaust system, part number MF15666. Now before we install the new MagnaFlow exhaust system, we'll go ahead and take a listen to the manufacturer's or current exhaust system. Next we'll go ahead and begin our install by disconnecting the exhaust here at the flange behind the catalytic converter. To do that, we'll remove the two nuts off the studs. We'll then remove the two rubber isolators from our exhaust pipe and tail pipe. To remove the rubber isolators, use a pry bar, pliers, or exhaust hanger removal tool. more


Watch Video

8/9/2013 11:40:47 AM



MagnaFlow Exhaust System Installation - 2000 Chevrolet Silverado- Video

MagnaFlow Exhaust System Installation - 2000 Chevrolet Silverado

Today on our 2000 Chevy Silverado, we'll be installing the MagnaFlow Stainless Steel Cat-Back Exhaust System, part number MF15754. To begin our install we'll first need to remove the old or manufactures exhaust. Starting at the exhaust flange just behind the catalytic converter, we'll go ahead and remove the exhaust stud nuts. Note: over time those will become corroded with rust, dust, dirt and debris, so I recommend spraying them down with some spray lubricant. Now with the nuts sprayed down, we'll go ahead and remove the nuts from exhaust stud. With both those removed, we'll go ahead and set them aside for re-installation later. more


Watch Video

6/13/2013 4:01:37 AM



MagnaFlow Exhaust Installation - 2003 Dodge Ram- Video

MagnaFlow Exhaust Installation - 2003 Dodge Ram

Today on our 2003 Dodge Ram Pick-Up we'll be installing the Magnaflow stainless steel cat back exhaust system, part number MF15788. To begin our install we'll first need to remove the old or manufacturers exhaust. To do this we'll start at the exhaust pipe where we'll need to make a cut measuring from the catalytic converter back 10 1/2 inches as per the instructions. We'll go ahead and make a mark. Then using a reciprocating saw we're going to go ahead and cut the exhaust pipe in half. Now we've made or cut we're ready to go ahead and remove everything from our cut back. more


Watch Video

6/5/2013 1:55:59 PM



MagnaFlow Exhaust Installation - 2003 Ford F-250 Super Duty- Video

MagnaFlow Exhaust Installation - 2003 Ford F-250 Super Duty

Today on this 2003 Ford F250, were going to install part number mf16926 from Magnaflow. Our first step to install is to go ahead and remove the rock guard for transfer case. Since this is a four-wheel drive vehicle, we have to remove it. This will be reinstalled after were done. Were also going to remove the passengers side stabilizer link. Thats just going to give us some extra room to work around when we install the new system. more


Watch Video

2/25/2013 10:06:41 AM



MagnaFlow Exhaust Installation - 2008 Ford F-150- Video

MagnaFlow Exhaust Installation - 2008 Ford F-150

Today on our 2008 Ford F150 well be installing the Magnaflow turndown cap back exhaust system, part number MF17106. Before we can begin installing our new exhaust system well need to remove the old or manufacturers exhaust system first. For this application well be removing the muffler and tailpipe. To make it easier to remove the muffler and tailpipe it will first be easier to go ahead and remove the rubber isolators. There are total of three for this system, one just behind the rear axle, one just forward of the rear axle and one just forward of the muffler. Before we remove our hangers well go ahead and loosen up the clamp, securing the muffler exhaust pipe through the forward exhaust pipe. more


Watch Video

1/25/2013 7:16:47 AM



MagnaFlow Exhaust Installation - 2002 Ford F-350 Super Duty- Video

MagnaFlow Exhaust Installation - 2002 Ford F-350 Super Duty

Install-exhaust-2002-ford-f350-mf15979 Today, were working on the 2002 Ford F350 Super Duty. Were going to install the MagnaFlow performance exhaust part number MF15979. Before we can install our new exhaust we have to remove the old exhaust, so Im going to take a little spray lubricant, spray each one of the rubber hangers, make it a little easier to remove and reinstall later. We also see there some exhaust clamps that were going to need to be removed. Were going to thoroughly spay these down with some penetrating oil to make it a little easier to break them free and get them loose. Alright start removing the exhaust; were going to come up here to the turbo underneath the hood. more


Watch Video

12/19/2011 4:30:30 PM



MagnaFlow Exhaust Installation - 2005 Chevy Silverado 3500- Video

MagnaFlow Exhaust Installation - 2005 Chevy Silverado 3500

Alright, today on this 2005 Chevy Silverado 3500 diesel we are going to install part number MF17931 from MagnaFlow. The first thing we are going to do is remove the bolts for the flange right here. I am going to spray them down with some lubricant first. And this is where the exhaust will begin. We will leave one nut on there to hold everything together until we are ready to completely take the exhaust down. Alright, now we will move on to the rubber hangers. And we will go ahead and apply some lubricant to them as well to help remove them. 1:00 more


Watch Video

7/14/2011 2:46:40 AM



MagnaFlow Exhaust Installation - 2006 Pontiac Grand Prix GXP- Video

MagnaFlow Exhaust Installation - 2006 Pontiac Grand Prix GXP

Today on this 2006 Pontiac Grand Prix GXP we are going to install part number MF16726 from MagnaFlow. The first thing you do is get underneath the vehicle and we will spray down the bolts that are on the exhaust with some penetrant and that should hopefully loosen them up. When a car is a few years, these fasteners will be rusted pretty well so you may end up breaking them. So be prepared to just replace the fasteners. Now we are going to leave this nut partially on for now because we need to hold it up while we disassemble the rest of the exhaust. So we will move on down towards the back of the vehicle and we will add a strap to help hold up the exhaust while we remove the rubber isolators. Ok, we are going to spray down the rubber isolators with some penetrant and go ahead and remove them. It looks like we have them all done on the passenger side. Now we will move over to the driver side and remove those. 1:00 more


Watch Video

7/12/2011 1:05:31 PM



MagnaFlow Exhaust Installation - 2007 Ford F-150- Video

MagnaFlow Exhaust Installation - 2007 Ford F-150

Today on a 2007 Ford F-150 we will be installing a MagnaFlow performance exhaust, part number MF16523. Our first procedure is going to be soaking down our clamp and hardware. I highly recommend that you soak this down several times and let it sit for at least 30 minutes before trying to break this nut loose. These bolts tend to become extremely rusted and very difficult to remove. As you can see, we have already gotten this nut broken loose. This clamp is loose but, if it becomes difficult to back off, I recommend that you work the nut back and forth, on and off, breaking free the rust that has built up in the threads of the clamp. After giving it a few taps with the hammer, you will notice that the clamp came loose and broke the rust free. Now that my clamp is loose, I just want to spread it open a little bit to make it easier to remove the exhaust pipe. 0:58 more


Watch Video

5/2/2011 3:55:40 PM



MagnaFlow Exhaust Installation - 2005 GMC Sierra- Video

MagnaFlow Exhaust Installation - 2005 GMC Sierra

Alright, today on this 2005 GMC Sierra we are going to install part number MF15841. Alright the first thing we need to do is go ahead and start getting the truck ready to install the exhaust. What we did is removed the spare tire. You do not have to do that but it makes things a lot easier to get to. It makes everything easier to see as well. Now we also have to remove the exhaust. So what we are going to do first off is go ahead and start removing the rubber hangers from the exhaust and also the bolts that connect the exhaust to the catalytic converter up front. So we are going to loosen these up first. That way, it puts less stress on the pipes up front when we disconnect the exhaust. Now you want to spray these down really go with a type of penetrant so you do not break the bolts. OK, we have that one loose. 1:05 more


Watch Video

3/25/2011 2:55:44 PM



MagnaFlow Exhaust Installation - 2001 Ford Ranger- Video

MagnaFlow Exhaust Installation - 2001 Ford Ranger

Today on this 2001 Ford Ranger we are going to install part number MF15679 from MagnaFlow. The first thing we are going to do to get ready is go ahead and move the spare tire. You do not have to do that but it makes things a lot easier to get to and see. The next thing we are going to do is spray down the bolts going towards the catalytic converter. Let it sit for awhile and we will go ahead and loosen them up. And also, you will notice, this is not the original factory connection going to the catalytic converter too. This is actually another aftermarket exhaust. We will leave that set for now. Now we will go back to the rest of the exhaust and remove all of the rubber hangers. Just spray them down with some lubricant also and pull them apart. Alright, we will just push it to one side and pull it out. And then we will pull out the other side. You should be able to pull it all out as one piece. 0:56 more


Watch Video

3/16/2011 10:04:26 AM



MagnaFlow Exhaust Installation - 2009 Chevrolet Silverado 1500 Series- Video

MagnaFlow Exhaust Installation - 2009 Chevrolet Silverado 1500 Series

Today on this 2009 Chevrolet Silverado 1500 Series extended cab short bed we are going to be installing MagnaFlow exhaust system part number MF16568. We are underneath the vehicle and the first thing I have done is lowered the spare tire out of the way to give us some extra working room. We also want to disconnect the battery. What that is going to do is once we get the system installed we can reconnect it and it will actually reset the computer system so it does not bring up any trouble codes from the new system. The first step before we can install our exhaust system is to of course remove the factory installed exhaust. There are four exhaust hangers that we are going to need to remove the exhaust off of towards the more rear side of the exhaust system. 00:39 more


Watch Video

7/8/2010 4:36:32 AM



MagnaFlow Exhaust Installation - 1996 Acura Integra- Video

MagnaFlow Exhaust Installation - 1996 Acura Integra

Today on this 1996 Acura Integra we are going to install MagnaFlow exhaust part number MF15653 from MagnaFlow Performance. First off we will give you a sound test of the original exhaust on there. Then we can compare it to the new one once we have it installed. First we will show you what is going to get replaced in our exhaust system. Basically this is what is called a Cat-back or from the catalytic converter on back to the tailpipe. This is our converter right here and at this flange point we are going to unbolt right here and from here on back is going to get removed from the vehicle. On the bolts themselves we sprayed down with some penetrate and let it sit for at least an hour or so. The nut on the top is going to be a different size nut also. Leave that alone for now. 00:50 more


Watch Video

6/30/2010 12:59:19 PM



MagnaFlow Exhaust Installation - 2007 Ford F-250 Super Duty- Video

MagnaFlow Exhaust Installation - 2007 Ford F-250 Super Duty

Today on this 2007 Ford F-250 Super Duty we will be installing MagnaFlow performance exhaust part number MF16926. You need to do a couple of things in preparation before we get started installing our exhaust system. First we want to disconnect the vehicles battery. This will allow the computer to reset itself once we get the new system in place and that will help prevent electrical accidents. If your vehicle has four wheel drive we also need to go ahead and remove the transfer case rock shield. There are four bolts holding it on two per side. We will just set that off to the side for the time being. We also need to go ahead and remove the lower bolt from the rear passenger side shock. Again this will allow us to swing the shock out of the way to help make the removal of the system easier. 00:54 more


Watch Video

1/13/2010 3:08:26 PM



MagnaFlow Exhaust Review - 2004 Mustang Cobra- Video

MagnaFlow Exhaust Review - 2004 Mustang Cobra

Rev up your engines! Were going to give you an overview of the MagnaFlow Stainless Steel Cat-back exhaust system and what it can do for your vehicle. This dual exhaust system not only improves engine performance by increasing horsepower, torque, and fuel efficiency but also decreases exhaust gas temperature. The sleek stainless steel design was engineered with mandrel bent tubes. These tubes have the same diameter throughout the system ensuring a constant uninterrupted airflow decreasing exhaust turbulence. MagnaFlows intelligently designed mufflers are created with a layer of steel wool insertion that absorbs noise but still allows for the signature deep, throaty sound to let people know you are riding on a MagnaFlow. more


Watch Video

12/14/2009 6:15:42 AM



MagnaFlow Exhaust Installation - 2005 Infiniti G35- Video

MagnaFlow Exhaust Installation - 2005 Infiniti G35

Today we are going to be installing Magnaflow Performance Exhaust system part number 16641on a 2005 Infiniti G35 Coupe. Before we get started we want to go ahead and disconnect the negative terminal off the battery. The battery is located behind this panel here on the upper left-hand side of the engine compartment. This going to allow the computer to reset so when we get the new exhaust system on it will reconfigure itself to the new exhaust. more


Watch Video

8/31/2009 1:46:20 PM



Lowering Exhaust Pipe on Vehicle with Rubber Hanger- Video

Lowering Exhaust Pipe on Vehicle with Rubber Hanger

Next what we have to do is lower the exhaust here a little bit, we will take off this rubber hanger and that way we get more flexibility and room to fit the hitch in. more


Watch Video

8/7/2008 1:45:29 AM



Lowering Exhaust Example for Trailer Hitch Installation- Video

Lowering Exhaust Example for Trailer Hitch Installation

The first step to do is to lower the exhaust and we will do that by taking off the rubber hangers on the front and back, and there is one hidden in the back. more


Watch Video

7/17/2008 12:20:19 AM



  1