Tow Bar Wiring Installation And Review Videos


Roadmaster Tow Bar Wiring RM-155 Review- Video

Roadmaster Tow Bar Wiring RM-155 Review

Today we're going to be taking a look at part number RM-155. This is the road master taillight wiring kit with the included sockets and bulbs. This kit is going to let you use your toed vehicles, brake, running and signal lights without taping into the vehicle wiring. Please note, to get this installed your toed vehicle must have enough room inside the tail light lens housing for an extra bulb and socket assembly. The size hold that you're going to need in order to get the socket mounted in the taillight housing is going to be one inch in diameter. You can use a one inch hole saw or a rotary cutting tool to make that hole. When you're installing this your wiring is going to be routed beneath the vehicle. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2011 Cadillac SRX- Video

Roadmaster Tail Light Wiring Kit Installation - 2011 Cadillac SRX

Today on this 2011 Cadillac SRX, we're going to install part number RM-155 from Roadmaster. This is a Roadmaster tail light wiring kit with bulbs. To start off our install, we're going to go ahead and get access to our wire harness. Now we're going to need to start off with the large wire harness with two inaudible 00:00:17. We'll go ahead and remove one of the ends. We'll talk this end and thread it from the front of the car towards the back. We'll start off by running it through the grill and up by the base plate. To help with the routing, we'll loosen up the bottom inaudible 00:00:30 by removing these screws. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Chevrolet Captiva Sport- Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Chevrolet Captiva Sport

Today on our 2013 Chevy Captiva we'll be installing the Roadmaster taillight wiring kit with bulb and socket, part number RM-155. First we'll go ahead and open up the rear hatch. We'll then access the two fasteners behind the taillight assembly. Once we remove the two fasteners we can then pop the taillight assembly out of its position to gain access to the back of the taillight assembly. Now with our driver's side out, we'll move over to the passenger's side and repeat the same process. We'll need to find a suitable location for mounting the new bulb and socket. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2018 Chevrolet Equinox- Video

Roadmaster Tail Light Wiring Kit Installation - 2018 Chevrolet Equinox

Speaker 1: Today in our 2018 Chevrolet Equinox, we're going to be taking a look at showing you how to install, the Roadmaster taillight wiring kit with bulbs, part number RM-155. So here's what our wiring is going to look like once we have it installed. It's going to provide us with a four pole flat to give us all of our lights when we're flat towing our Equinox down the road. It's going to give us our turn signals for the left and right, the brake lights, as well as our taillights. It's going to completely bypass our vehicle's wiring system, so we're not going to have worry about voiding out the manufacturer's warranty. It's going to be a completely standalone system that's going to wire from the front. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Chevrolet Silverado 1500- Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Chevrolet Silverado 1500

All right. Today it's 2014 Chevrolet Silverado 1500 Crew Cab. We're going to install Part number RM-155. This is Road Master Tail Light Wiring Kit with bulbs. Let's go ahead and lower the tailgate, and starting on the driver's side we'll go ahead and remove the tail light. Looks like there's two fasteners that we have to remove. Now when you take the tail light off, you want to pull straight back. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2016 Chevrolet Sonic- Video

Roadmaster Tail Light Wiring Kit Installation - 2016 Chevrolet Sonic

Today on our 2016 Chevrolet Sonic we are going to be taking a look at and installing the Road Master Tail Light Wiring Kit with Bulbs part number RM-155. Here's what it looks like once it's installed on the vehicle. Right now we've got the tail lights on so you can get a feel for how bright it's going to be and in there you can see the extra bulb that we put in there that's currently on along with the factory bulb. The new bulb is going to give us both tail lights, and turn, and brake signals in order to properly alert vehicles behind us when we're towing that our vehicle and our RV are stopping or turning. This lighting system is going to do a good job of making sure that the vehicle is seen behind the RV but another nice thing about this is that it doesn't tap into the vehicle's wiring system at all. It wires directly into the wiring that you install coming from the motor home. Therefore, you can avoid possibly having a back feed or surge in the electrical system of the vehicle. Now, let's go ahead and show you how to install it. First thing we'll need to do is get our wiring routed. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Chevrolet Sonic- Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Chevrolet Sonic

Today on our 2013 Chevy Sonic we'll be installing the Roadmaster Tail Light wiring kit with bulb, part number RM-155. In conjunction with our Pollak 4-Pole Round Pin socket, part number PK11410. To begin our install we'll open up the rear hatch. We're going to be removing the tail light assembly to make it easier to install the wiring harness. To start, we'll go ahead and remove the two fasteners on each side that secure the tail light assembly. Once we remove the fasteners we'll go ahead and pop the tail light housing out. We'll then rotate the light so that we can let it hang here until we're ready to make our wiring connections. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Chevrolet Sonic- Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Chevrolet Sonic

Today on our 2012 Chevrolet Sonic, we'll be installing the Road Master tail light wiring kit with bulbs, part number RM-155-. We're going to go ahead and remove this pannel right here, to give us some access to the base plate, so we can connect our wiring to it. In order to remove this pannel, we'll need to take down multiple fasteners. We're going to go ahead and take one end of our long spool of four-flat wiring. We're going to go ahead and route it down through the engine department here, and come out underneath. Now we'll go ahead and take our four-flat wiring, and we'll route it across the back side of the base plate, over to where our bracket will be mounted. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2010 Ford Explorer- Video

Roadmaster Tail Light Wiring Kit Installation - 2010 Ford Explorer

Today on our 2010 Ford Explorer, we're going to show you how to install the Roadmaster Bulb and socket kit with bulbs part number RM-155. We'll hook our tow vehicle up to the front here, we'll start by turning on the taillights. With those working, let's check the left blinker, then our left break. Now our right blinker and our right break. Now as you can see, we mounted our plug in the position we went right on top of the bumper structure there. That way we wouldn't have any issues once we had everything on and trying to get it installed. WE're going to take care of getting our bracket mounted for where our wiring's going to go up here in the front. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2015 Ford Focus- Video

Roadmaster Tail Light Wiring Kit Installation - 2015 Ford Focus

Today on our 2015 Ford Focus we're going to be taking a look at and installing the Roadmaster taillight wiring kit with bulbs, part number RM-155. With this system you're not going to tie into any of your factory wiring. This is a completely self sufficient system running off the wiring of your coach. There's no need to tap or splice into any factory wiring or add any diodes because it's a separate bulb and socket that go into each of your taillights. Now this is what your kit's going to consist of. You're going to have a 30 foot long piece of four flat wiring with ends on both sides. We'll have a six foot jumper harness that's going to be used for going between your coach and your vehicle. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Honda CR-V- Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Honda CR-V

Today in our 2014 Honda CRV, well be installing the Roadmaster Tow Bar Wiring Kit with bulb and socket, part number RM-155. To begin our install, well first need to remove the tail light assemblies. To remove the tail light assemblies, well open up the rear hatch and then remove the two fasteners that secure the tail light assembly to the body. Next, well go ahead and gently remove the tail light assembly from its position releasing the fasteners and being careful not to break the alignment tabs underneath. When the tail light assembly is pulled out, we can see the back of the tail light assemblies where well mount the bulb and socket.To mount the bulb and socket well first need to drill a hole under the back of the tail light assembly as per the instructions. Well use a 1-inch hole saw. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Honda CR-V- Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Honda CR-V

Today on our 2013 Honda CRV we'll be installing the Roadmaster Taillight Wiring Kit with bulbs, part number RM-155. First thing we need to do is get our vehicle ready. To do that we need to remove the taillights. We'll start off by opening up the back hatch where there are two Phillips head fasteners that we need to remove. We'll take our taillight and pull it this way until we can work it loose. Then there's a guide here that makes you pull it backward. Now we can go ahead and remove our taillight from the vehicle. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2011 Honda CR-V- Video

Roadmaster Tail Light Wiring Kit Installation - 2011 Honda CR-V

Today on our 2011 Honda CRV, we'll be having a look at and installing the Roadmaster tail light wiring kit with bulbs, part number RM-155. Here's what our bulb and socket kit looks like installed. What this kit allows us to do is have a tow vehicle lighting system installed on our vehicle, that is completely separate from the vehicles' lighting circuitry that's already existing. We don't have to worry about cutting our wiring putting diodes in place. This will isolate our vehicles electrical system completely, treating it just like a trailer with a separate bulb. What's great about this kit compared to using a magnetic tow lights is, you don't have to worry about putting on top of your vehicle, scratching your paint when removing them or with a removed round or having them fall off or someone take them. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2010 Honda CR-V- Video

Roadmaster Tail Light Wiring Kit Installation - 2010 Honda CR-V

Today on our 2010 Honda CR-V, we'll be taking a look at and installing the Roadmaster tail light wiring kit with bulbs, part number RM-155. First thing we'll need to do in our installation of our Roadmaster tail light kit with bulbs is go ahead and open up our rear hatch to gain access to our tail light assemblies. Then, we will remove the caps located here and here on both sides. To remove the tail lights, use a small screwdriver to stick in the slot and pop it out. Once you've popped out both the caps, repeat that same process on the passenger side. Anything we do here on the driver side, as far as the removal and re-installation of the tail lights, is going to be repeated on that passenger side. All right. Now, we're going to remove the two bolts on the inside. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Hyundai Accent- Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Hyundai Accent

Today on this 2012 Hyundai Accent, we're going to show you part number RM-155. This is a Roadmaster Taillight Wiring Kit with bulbs. Now our bulb and socket kit, typically installs in the taillights. In our car here, they're installed at the lower part of the taillight. This is our driver's side, it's going to be the same thing over on our passenger's side. Now you get a length of wire that runs from the back of the car all the way up towards the front as well. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Hyundai Elantra- Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Hyundai Elantra

Sending in our 2013 Hyundai Elantra. We'll be installing the Roadmaster Tail Light Wiring Kit with Bulbs, Part Number RM-155. To begin with here, we'll take the long wire that has a plug on both ends. We'll actually snip one of the plugs off because we will not be needing it on this particular application. Now, as you can see, this vehicle already has the baseplate installed on it, so we'll be rodding the wire and tying it in right near the center of the baseplate area. To rod our wire, we will be using an old section of airline tubing to help us pull the wire through the inching department and underneath the vehicle. We're going to go ahead and take our piece of airline tubing and start from the engine compartment and rod it down in front of the radiator where we'll pull the four-flat out. Now, it's a good idea to leave a little extra wiring here in case you want to add the different style plug instead of the four-flat, whether it'd be a four or six round at a later time. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2002 Jeep Liberty- Video

Roadmaster Tail Light Wiring Kit Installation - 2002 Jeep Liberty

Today on this 2002 Jeep Liberty we're going to install part number RM-155 from Roadmaster. This is Roadmaster taillight wiring kit with bulbs. First thing we need to do is go ahead remove the taillights from the vehicle. There's two torx head bolts that we have to remove. We use a T20 torx head bit to remove the bolts. There's a couple attachment pins here and here. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Jeep Patriot- Video

Roadmaster Tail Light Wiring Kit Installation - 2014 Jeep Patriot

Today on our 2014 Jeep Patriot, were installing a roadmaster tail light wiring kit with bulbs part number RM-155. Now, were going to begin up here at the front of the vehicle. Well go ahead and raise the hood up. Now, were going to take the long wire that has two four flat ends to it. Were actually going to cut one of the four flat ends off. Now the end that we keep that has a four flat connected to it, were actually going to mount up underneath the grill in this vehicle.Now, this vehicle already has a base plate installed so well be connecting it up here at the base plate. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 1998 Jeep Wrangler- Video

Roadmaster Tail Light Wiring Kit Installation - 1998 Jeep Wrangler

Today on our 1998 Jeep Wrangler, we'll be installing the Road Master Taillight Wiring Kit with bulbs, part number RM-155. To being with, we're going to go ahead and open up the hood of the vehicle. We're going to cut one end of the four flat off. We will not need this in this application. Next we're going to route our wire through the grill and through the engine compartment. It's a good idea to keep a couple extra feet up near the front of the vehicle in case if you have to replace a plug or move the location where your plug may attach to your vehicle. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Jeep Wrangler Unlimited- Video

Roadmaster Tail Light Wiring Kit Installation - 2012 Jeep Wrangler Unlimited

Today on our 2012 Jeep Wrangler Unlimited, we will be installing the Roadmaster Tail Light Wiring Kit with bulbs, part number RM-155. To begin with, we'll need to route our wires from the front of the vehicle towards the back. To accomplish this, we'll be using a pull wire, in this case a piece of old airline tubing. When we get past the engine compartment, we can route the wire through the frame all the way to the back. Here at the front of the vehicle we will also protect our wire with the loom material provided with the install kit. We can secure it in place with electrical tape. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2009 Mini Cooper- Video

Roadmaster Tail Light Wiring Kit Installation - 2009 Mini Cooper

Today, on this 2009 Mini Cooper, we're going to install part number RM-155 from Roadmaster. The first thing we're going to do is start from the front of our car and work our way back. To help run our wire through our grill, we're going to use a piece of airline tubing. This could also be a piece of fish wire or another piece of wire, to help it through. We'll run it through the grill, and then underneath, where we can reach it. Next, we'll load our wire harness. It has two 4-pull ends on it. Doesn't matter which end, but we need to remove one. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2008 Nissan Frontier- Video

Roadmaster Tail Light Wiring Kit Installation - 2008 Nissan Frontier

Today, on this 2008 Nissan Frontier, we're going to show you part number RM-155. This is the Roadmaster tail light wiring kit with bulbs. First off, you get the main wire harness that gets ran from the back of the vehicle all the way up towards the front. Your bulb and sockets right here that get installed into the tail lights, a length of loom material to help protect the wires or hide the colors of the wires when they're exposed to the outside. Some butt connectors to make your wire connections. Also, a ring terminal here for your ground. more


Watch Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Ram 1500- Video

Roadmaster Tail Light Wiring Kit Installation - 2013 Ram 1500

Today on our 2013 Ram 1500 we're going to review and install the Roadmaster taillight ball and socket wiring kit for two bar wiring, part number RM-155. Now here's what our brake light will look like when it's engaged. Next we'll go ahead and show you the passenger side turn signal. Here's what it will look like for the brake light on the driver side. Here's the driver side turn signal. Now to begin our install we need to remove the rear taillights. We'll go ahead and lower the tailgate and locate the two fasteners that secure each taillight. more


Watch Video

  1