Trailer Hitch Installation - 2014 Ford Edge - Curt- Video

Today on our 2014 Ford Edge, we're going to be taking a look at and installing the CURT trailer hitch receiver for the class three hitch, part number C13067. This is what the CURT hitch looks like once it's installed on the vehicle. On this Ford Edge Sport, you can see that it's nicely tucked up underneath and very well hidden. All you can see is the receiver tube here, along with the round steel looped safety chain hoops. This hitch is a fairly easy installation. It bolts into place with minimal drilling required. more

Watch Video

Trailer Hitch Installation - 2013 Ford Edge - Curt C13067- Video

Today on our 2013 Ford Edge, we'll be installing car hitch part number C13067. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch so it's a ball mount, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is four-and-a-half inches. From the top of the inside of the receiver tube opening to the ground is 12 3/4 inches. Now let's go ahead with installation. more

Watch Video

Trailer Hitch Installation - 2012 Ford Edge - Curt C13067- Video

Today on our 2012 Ford Edge we'll be installing the Curt Hitch, part number c13067. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is four and a quarter inches.From the top of the receiver tube opening to the ground is 12 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. Now let's go ahead with installation. more

Watch Video

Trailer Hitch Installation - 2011 Ford Edge - Curt- Video

Today on our 2011 Ford Edge, we'll be installing the Curt hitch, part number C13067. Now here's what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist you in selecting accessories for new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 5 1/4 inches. From the top of the receiver opening to the ground is 13 inches. This will assist you with selecting accessories such as a ball mount, bike rack or cargo carrier. Now to begin our install we'll first lower the exhaust. more

Watch Video

Trailer Hitch Installation - 2010 Ford Edge - Curt C13067- Video

Today on our 2010 Ford Edge we're going to take a look at, then show you how to install the CURT custom fit trailer hitch receiver. This is a class three 2" opening hitch. Part number is C13067. Here's what the hitch is going to look like once installed on the vehicle. See it's going to be visible for about this distance, about from here over to here. Doesn't hang down from the bottom very much. more

Watch Video

Best 2010 Ford Edge Hitch Options- Video

Today we're going to be taking a look at the best hitch options for your 2010 Ford Edge. Up top we're going to have the Curt Class 3, part number C13067. Followed by the draw tight class 3, part number 75992. Finally the Curt class 2, part number C12036. The biggest difference that you're going to see between these hitches is on the draw tight. The cross tube is going to be completely tucked behind the fascia because this receiver tube is welded to the bottom of that. more

Watch Video

Trailer Hitch Installation - 2009 Ford Edge - Curt- Video

Today on our 2009 Ford Edge we're going to be installing the Curt Trailer Hitch Receiver, part number C13067. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the opening in the receiver to the ground, we have about 13 inches. From the center of the hitch pin hole to the outermost edge of the bumper, we have approximately 5 inches. Now let's go ahead and install our hitch. We're going to begin here underneath the vehicle by installing a safety strap underneath the exhaust to support it. more

Watch Video

Best 2009 Ford Edge Hitch Options- Video

Today we're going to be taking a look at the best hitch options for your 2009 Ford Edge. Up top we're going to have the CURT class three, part number C13067; followed by the Draw-Tite class three, part number 75992; and finally the CURT class two, part number C12036. The biggest difference that you're going to see between these two hitches is on the Draw-Tite the crosstube here is going to be completely tucked behind the fascia because this receiver tube is welded to the bottom of that, where on both CURT's it's welded in-line with that crosstube so you are going to be able to see some of that crosstube from underneath the rear fascia. On this Draw-Tite it's going to have two pinholes. It's got the standard 5/8" hitch pinhole that's going to be used to secure all the class three accessories. It also has the smaller 1/2" hole which is going to be good for use with a j-pin stabilization system, which helps to eliminate so that shake and play in the shank to help provide a nice quiet, secure ride for your accessories. The class three CURT has this nice large reinforcement plate that's welded onto the top of the crosstube and the top of the receiver tube opening, which helps give it extra stability and durability. Also, when looking at the hitch on the vehicle, that helps give it a little bit cleaner look as well. more

Watch Video

Trailer Hitch Installation - 2008 Ford Edge - Curt- Video

Today on our 2008 Ford Edge, we'll be installing Curt Hitch, part number C13067. Now before we begin our installation, heres what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost part of the bumper is 5-1/2 inches. From the top of the receiver tube to the ground is 13-1/4 inches. Now, let's go ahead with our install. more

Watch Video

Best 2008 Ford Edge Hitch Options- Video

Today we're going to be taking a look at the best hitch options for your 2008 Ford Edge. Up top we're going to have the CURT class three, part number C13067; followed by the Draw-Tite class three, part number 75992; and finally the CURT class two, part number C12036. The biggest difference that you're going to see between these two hitches is on the Draw-Tite the crosstube here is going to be completely tucked behind the fascia because this receiver tube is welded to the bottom of that, where on both CURT's it's welded in-line with that crosstube so you are going to be able to see some of that crosstube from underneath the rear fascia. On this Draw-Tite it's going to have two pinholes. It's got the standard 5/8" hitch pinhole that's going to be used to secure all the class three accessories. It also has the smaller 1/2" hole which is going to be good for use with a j-pin stabilization system, which helps to eliminate so that shake and play in the shank to help provide a nice quiet, secure ride for your accessories. The class three CURT has this nice large reinforcement plate that's welded onto the top of the crosstube and the top of the receiver tube opening, which helps give it extra stability and durability. Also, when looking at the hitch on the vehicle, that helps give it a little bit cleaner look as well. more

Watch Video

Best 2007 Ford Edge Hitch Options- Video

Today we're going to be taking a look at the best hitch options for your 2007 Ford Edge. Up top we're going to have the CURT class three, part number C13067; followed by the Draw-Tite class three, part number 75992; and finally the CURT class two, part number C12036. The biggest difference that you're going to see between these two hitches is on the Draw-Tite the crosstube here is going to be completely tucked behind the fascia because this receiver tube is welded to the bottom of that, where on both CURT's it's welded in-line with that crosstube so you are going to be able to see some of that crosstube from underneath the rear fascia. On this Draw-Tite it's going to have two pinholes. It's got the standard 5/8" hitch pinhole that's going to be used to secure all the class three accessories. It also has the smaller 1/2" hole which is going to be good for use with a j-pin stabilization system, which helps to eliminate so that shake and play in the shank to help provide a nice quiet, secure ride for your accessories. The class three CURT has this nice large reinforcement plate that's welded onto the top of the crosstube and the top of the receiver tube opening, which helps give it extra stability and durability. Also, when looking at the hitch on the vehicle, that helps give it a little bit cleaner look as well. more

Watch Video

Trailer Hitch Installation - 2015 Lincoln MKX - Curt- Video

Speaker 1: Today in this 2015 Lincoln MKX we'll be having a look at and showing you how to install the Curt Class 3 trailer hitch receiver, part number C13067.Here's what our hitch looks like installed. First thing you'll notice about this hitch is that we do have plenty of clearance around our receiver. This makes this a great hitch to use with bike racks and cargo carriers, which is what many of our customers are using this hitch for. Now when comparing this to other options out there, this hitch is a little bit more visible in the center section here, but this is tucked nicely up against the rear fascia, so it does maintain a nice clean look.Inside of our receiver, you'll find our industry standard 5/8 of an inch diameter hitch pin hole to secure your hitch mount and accessories. You can pick up a pin and clip separately on our website. Welded on the bottom of our receiver, our rolled steel safety chain loops. more

Watch Video

Trailer Hitch Installation - 2014 Lincoln MKX - Curt- Video

Today in our 2014 Lincoln MKX, we'll be installing the Curt Class III Trailer Hitch Receiver, part number C13067. Here's what a hitch looks like installed. As you can see, it's a very factory-like appearance. It's tucked up nicely behind a rear bumper cover here. The only part really hanging down is the class III receiver here and a little bit of the rectangular frame of the hitch, has a nice high-gloss black powdercoat finish, so it's very durable. This hitch has a 4,000 pound gross trailer weight rating and a 400 pound tongue weight rating. It does not support weight-distribution. We have these nice, round, tubular constructed safety-chain hooks that will be able to fit the smallest diameter of safety chains onto without a problem. more

Watch Video

Trailer Hitch Installation - 2013 Lincoln MKX- Video

Today on this 2013 Lincoln MKX, we're going to show you the Curt class 3 two inch receiver hitch, part number C13067. This is what the hitch looks like once installed in the vehicle. At first glance you can see the receiver opening right here, and you can see the body of the hitch. It does sit below the bumper, but it quickly goes back up and underneath the bumper and up into the frame. If we take a closer look at the opening here, this is our two inch receiver, it has a nice rounded collar all the way around it, kind of a uniform finish on the front and the back. If you take a look on the back it has a loop on the bottom for your safety chains. more

Watch Video

Trailer Hitch Installation - 2010 Lincoln MKX - Curt- Video

Today on our 2010 Lincoln MKX, we're going to install the Curt Hitch, part number C13067. Here are a couple of measurements that assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost point of the bumper is 5-1/2 inches. From the top of the receiver tube to the ground is 12-1/2 inches. Now, let's go ahead with the installation. Our first step, we need to lower the exhaust. more

Watch Video

Best 2009 Lincoln MKX Hitch Options- Video

Today we're going to be taking a look at the best hitches available for the 2009 Lincoln MKX. Starting at the top we've got the CURT, part number C13067. It's going to be a class three that offers the 2" by 2" opening. We're going to follow that up with the Draw-Tite, part number 75992, also a class three with the 2" by 2" opening. Finally, we've got our Draw-Tite class two, which is the 1-1/4" by 1-1/4" opening. Its part number is 36447. Now the biggest noticeable difference that we're going to see with our hitches is the way the receiver tube opening meets our crosstube. more

Watch Video

Trailer Hitch Installation - 2009 Lincoln MKX - Curt- Video

Today on our 2009 Lincoln MKX, we'll be having a look at and installing at the Curt Trailer Receiver, Class III, 2-inch Hitch, part number C13067. Now that we have our hitch completely installed, you can see it has a nice clean look here. There's a very minimal amount added to the vehicle showing down below. Most of it is hidden up underneath where you can't see it. We have a standard 2-inch receiver opening here with a 5/7-inch diameter pinhole to secure your draw bar for towing a trailer, your bike rack, your hitch cargo rack, things of that nature. We have these nice welded loops on the side of it to secure the safety chains on your trailer. We have a 4,000-pound gross trailer weight rating on it with a 400-pound max tongue weight rating. Again, you want to consult with the owner's manual of your vehicle to see whichever is less and go by that. Now, to give you a few measurements to help with choosing any accessories to go with your hitch, we have about 14-1/2 inches from the ground to the top edge of the inside of the receiver tube. more

Watch Video

Trailer Hitch Installation - 2008 Lincoln MKX - Curt C13067- Video

Today in our 2008, Lincoln MKX well be installing the Curt hitch part number C13067. This is what our hitch well look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch, pinhole to the outer most edge of the bumper is six inches. From the top of the received tube to the ground is 13-1/2 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or a cargo carrier. more

Watch Video

Best 2008 Lincoln MKX Hitch Options- Video

Today we're going to be taking a look at the best hitches available for the 2008 Lincoln MKX. Starting at the top we've got the CURT, part number C13067. It's going to be a class three that offers the 2" by 2" opening. We're going to follow that up with the Draw-Tite, part number 75992, also a class three with the 2" by 2" opening. Finally, we've got our Draw-Tite class two, which is the 1-1/4" by 1-1/4" opening. Its part number is 36447. Now the biggest noticeable difference that we're going to see with our hitches is the way the receiver tube opening meets our crosstube. more

Watch Video

Best 2007 Lincoln MKX Hitch Options- Video

Today we're going to be taking a look at the best hitches available for the 2007 Lincoln MKX. Starting at the top we've got the CURT, part number C13067. It's going to be a class three that offers the 2" by 2" opening. We're going to follow that up with the Draw-Tite, part number 75992, also a class three with the 2" by 2" opening. Finally, we've got our Draw-Tite class two, which is the 1-1/4" by 1-1/4" opening. Its part number is 36447. Now the biggest noticeable difference that we're going to see with our hitches is the way the receiver tube opening meets our crosstube. more

Watch Video

  1