Customers compare APUBR-9 to these similar products
Products Featured in this Video
Today on our fifth wheel trailer we'll be installing the Red Line U-Bolt Kit for mounting 5,200 pound to 7,000 pound round trailer axles. This is part number APUBR-9. Here's what our kit consists of. We have the two flanges here that will go on top of our axle which will secure our u-bolts to the top and hold our axle in place to release springs. We have the necessary two, one per side and then… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part #APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that…
view full answer...To convert your axle for a top mounted leaf spring I would recommend replacing the U bolts, nuts and tie plates, so your best bet would be to go with a U bolt kit. For a 2-3/8" round axle use #APUBR-1 For a 3" round axle use…
view full answer...Per Dexter your axle will need the Grease Seals #RG06-070. We also have the Bearing Kit #BK3-300 that will provide you with new wheel bearings, races, a grease seal and cotter pin. I recommend having one or 2 of the bearing kits with the trailer in…
view full answer...The 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles #e27SR are going to be the closest leaf springs we have for your 2012 Jayco 23.5 travel trailer. These springs have the same 26" measurement. While these will help to raise the height lost…
view full answer...The best way to measure a trailer spring for purposes of selecting a replacement is to remove it completely from the suspension. It is also important to note that leaf springs will tend to elongate over time as they wear. You might pull a well-worn…
view full answer...As long as the axle the won't exceed 5,000 lbs the trailer leaf spring #e44SR would work great since it has a 5k capacity. If you need the full capacity of your axles you'd have to move up to a 6k spring with the part #e34SR instead. This…
view full answer...Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…
view full answer...You will have to do some measuring. Take a look at our Double-Eye Trailer Suspension article (see link). I have also linked a picture of a shackle link showing where to measure. Measurements for replacement 1) Measure current shackle from center of…
view full answer...The arms on your Fastway e2 Weight Distribution System #FA94-00-0800 can be removed by either pulling on the keeper tab to release them, or by swinging them outward to be perpendicular to the tow vehicle. At this point, the arm should drop freely…
view full answer...The only differences between the two hubs you mentioned #8-201-9UC3-EZ and #8-201-5UC3-EZ are that the 8-201-5UC3-EZ is not pre-greased and the other is and they have different bearing between the two. But the bearings both have the same inner…
view full answer...Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…
view full answer...To replace the U-Bolt kit on your 5.2K axles I recommend the following kit: - Replacement U-Bolt Axle Mounting Hardware Kit #LC27XV This comes with U-Bolts for 3" diameter axles, the mounting plate, and the hardware needed to get everything…
view full answer...