Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2017 GMC Acadia Limited

content loading



Customers compare RM-15267 to these similar products


Products Featured in this Video



How to Install the Roadmaster Diode 7 to 6 Wire Coil Kit on a 2017 GMC Acadia Limited


Today on our 2017 GMC Acadia we're going to be installing road masters dialed wiring kit. If the tow bar you have came with the coiled cable or you already have one, you can get Roadmaster's Universal Hy-power Diode Wiring kit, which comes with the diodes and the wiring. It does not come with the six foil connector or the coiled cable.As far as your complete flat tow setup, you're going to need your base plate, your wiring kit, your braking system, and your tow bars. And in the event your tow bar doesn't come with safety cables, you'll need to get some of those as well.This diode wiring kit is going to allow our motor homes, turn, stop and tail lamp signal to be transferred from the motor home to our vehicle and our lights illuminate appropriately to display those signals behind us.What's great about the diodes is that it isolates the circuits that's on your vehicle from the ones coming from your motor home so you don't have to worry about any back feeding causing damage to your vehicle.To install your diodes and your wiring, you are going to need to remove your taillights on both the driver and the passenger side. They come out fairly easily, you'll need to open your lift gate, there'll be two little plastic covers, just pop those out of your taillight assembly with a flat bladed screw driver. Then you can remove both the bolts that are located there with a 7 millimeter socket.

After that, your assembly will just rearward to remove it. There's a small pin that still holds it in, in the this little grommet.The diodes themselves will then hook in-line with your taillight wiring. We'll need to hook-up the turn signal and taillight wiring on both the driver and passenger side. Our purple circuit here is for our taillights and our yellow circuit here is for our turn signals. So, we're going to cut that wire.

We'll then attach the included blue spade terminals onto each of those wires that we cut and we'll need to feed our wiring up through the slot here in the bumper. The best way to do this is to use a fish wire. You can use a coat hanger, we're using a piece of airline tube. We slide it down from the top until we can grab it below. Then we'll use some electrical tape to tape our wiring to that and just pull it right back up.

That's the easiest way to get your wiring up here.On our driver's side, you'll want to connect the yellow wire, which is your left turn signal, that's going to connect to the other yellow circuit here. So we have both of these on one side and the outside is always going to be on the connector side. So the single side, connector side.The other one is for our taillights. We're using the white wire here, it is typically the brown wire, but we used the brown wire on our passenger side, it really doesn't matter which one but both have to be connected together. I went ahead pushed all those back on.

Here on our passenger side, it's the same thing. We have the brown and white wires, our taillight. And the green wire is our turn signal. So we cut those, put our diodes in between and crimped on the included spade terminals onto each of those wires that we cut.We fed out wiring up the same way, the green wire from our wiring is going to connect with our turn signal, so that's the green wire here. The white wire from the other side was run across to this side and connected to the brown wire and they we're both crimped together onto the taillight circuit on this side. From this point, we can now run the rest of our wiring up to the front to be connected to our 6-pole connector.The rest of our wiring here, we routed past the spare tire, connected it to the factory wiring and just used that factory wiring to follow it up to the front. We want to avoid and moving objects, such as our suspension and steering components, and any excessively hot objects, such as our exhaust.If you follow factory wiring you will typically avoid any of those things. We then went down past our gas tank, along the side of it, then we followed that all the way up to our plastic panel here where we routed up to our engine compartment. We used out fish wire pull trick again to help pull it up into the compartment.From there we routed our wiring over to our driver's side here. The white wire we cut and separated from the rest of them. We crimped on a ring terminal and connected to the ground here. The rest of this white wire runs up to the front from this ground point to our 6-pole connector. And the rest of our wiring also runs to our 6-pole connector. So it goes down here, past the head light down along the side, across our bumper beam, over to where we connected our 6-pole connector. Our wiring will then connect to our 6-pole connector, the white wire is ground which is typically labeled "gd" on our connector. The brown wire is our taillights, which is typically labeled "tm", the yellow wire is our left turn signal, which is typically labeled "lt" and the green wire is our right turn which is typically labeled "rt".On the back side of our connector here, all of those will connect. You can just use a small Phillips or flat-plated screw driver to unscrew those, poke the wires in and then screw them back down in the appropriate spot. Depending on your base plate, there may or may not be a location to mount your 6-pole connector. This particular base plate did not include a place to mount your 6-pole connector so we had to use a long bracket as well as a 6-pole bracket. Both of these brackets are available here at etrailer.com.In order to get our electrical connection through our inaudible 00:05:24 when we reinstalled it, we did have to trim some out here next to out license plate. Our brackets are installed at the bottom of the bumper beam.We've got out test box here set-up and that just goes from a seven way to a 6-pole connector. This would be just as if you we're hooking it up to your motor home. This is going to simulate those signals. So we're going to turn it on and we're going to verify that all of our lights are working and we're going to see at the back of our vehicle.Here you can see we've got our left turn signal, right turn signal, tail lamps, and brake lamps.And that completes our installation of Roadmaster's Diode Wiring kit on our 2017 GMC Acadia.


Questions and Comments about this Video

add comment

Info for this part was:

Test Fit:
Joe V
Video by:
Andrew K
Installed by:
Jeff D
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Kathleen M
Video Edited:
Dustin K
Test Fit:
Randy B
Video Edited:
Chris R
Video Edited:
Zach D
Test Fit:
Andrew S
Test Fit:
Brent H
Test Fit:
Shane H
Video by:
Jonathan Y
Test Fit:
Robert C
Video by:
Michael B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.