bing tracking image

Draw-Tite Max-Frame Trailer Hitch Installation - 2021 Chrysler Pacifica

content loading

Customers compare 76046 to these similar products

Products Featured in this Video

How to Install the Draw-Tite Max-Frame Trailer Hitch on a 2021 Chrysler Pacifica

Hey, everyone. Shane here at Today, I have a 2021 Chrysler Pacifica. I wanna walk through how to install a Draw-Tite Class 3 Trailer Hitch Receiver. This is what our hitch is gonna look like when it's installed. Cross tube is completely hidden behind the fascia.

All that we can really see is our receiver tube, so it's gonna maintain a nice, clean look on the vehicle. Hitch itself's gonna be a steel construction, black powder coat finish, so it's gonna hold up really well against rust and corrosion. As I mentioned, being a class three it's gonna give us a lot of different options for hitch mount accessories. Maybe you wanna put a bike rack on because you're tired of loading the bikes inside and you really don't want to get a bike rack for the roof. Adding one on the back of the vehicle is gonna make it much easier.

Maybe you wanna get a cargo carrier, whether that's to move some stuff from inside to the outside and make more room for passengers, or you just wanna bring a few extra items with you. Maybe you wanna tow a small camper. This hitch is gonna allow you to do all that. You come right over here to our driver's side on our hitch, Draw-Tite's gonna have a pre-welded bracket and this is for any wiring accessories that you may wanna put on. You can find different wiring options here at etrailer.

I'm gonna give you some measurements and weight capacities to help you when deciding on any of those hitch mount accessories, like ball mounts, cargo carriers, and bike racks. From the center of our hitch pin hole to the outermost part of our fascia, we're looking at about 5 1/2 inches, and that one's important for any of the hitch mount accessories, like bike racks and cargo carriers when they fold up. You wanna make sure they're not gonna make contact. From the ground to the top innermost part of the receiver tube is about 12 inches. Keep that number in mind for any of your hitch mount accessories that may require a little bit more ground clearance.

I will recommend with it only being 12 inches off the ground to use the raised shank. You can find different options here at etrailer as well. As far as our weight capacities go, we're gonna have a 675 pound max tongue weight, which is the downward pressure on the inside of the receiver tube. You wanna make sure when you're putting the trailer on, cargo carrier, bike rack, you're not exceeding that. We're gonna have a 4,500 pound gross trailer weight, which is the trailer plus the load included. You can use weight distribution with this hitch. Tongue weight is gonna stay the same. However, trailer weight's gonna go up to 5,000 pounds. I always recommend checking the owner's manual of the vehicle. Make sure the vehicle can withstand that amount of weight. You're gonna go with the lowest number between the vehicle and the hitch. Now that we've gone over some of the features, let's walk through how to get it installed. To start your installation, we're gonna take an eight millimeter socket. We're gonna be removing the black bolts that run across the bottom back edge here, two on the lower edge on the driver's side, and then in the wheel well, we're gonna have three. One here and then two right here. And we're gonna take a 10 millimeter socket, we're gonna loosen the nuts that run from one side to the other, as well as two bolts right here, connecting this rear panel to this center one. Keep in mind, once you remove these two bolts, you're gonna have two of the plastic nuts under here. Then what we're gonna do is take a screwdriver, flathead. We're gonna kinda put some downward pressure on the panel as we turn that. We're gonna have one here and then we're gonna have another one right over here. Remove the panel and we'll set it aside. Then we're gonna take a strap, hang it from anywhere on the vehicle, go underneath your exhaust pipe, we'll cinch that up, and then we're gonna come back. We're gonna spray this hanger. Can use the lubricant, you can use some soapy water. This one here, and then we're gonna have one right here. We need to remove both of those. Once you have them sprayed down, you can take a pry bar and we're just gonna pry one end off of the pin. We're gonna take a 10 millimeter socket, we're gonna remove that nut on our heat shield, and then we'll have another one right here. Now this next step, you can do it if you want to. It's gonna make it a little bit easier for getting your hardware in on the passenger side. Make sure you have a strap underneath your exhaust. What we're gonna do is we're gonna remove this third one right here so that we can actually slide our exhaust away from our fascia, lower it even more. We're gonna do it the same way we did the other two. Next, we're gonna take our pull wire, a short spacer block, carriage bolt. We're gonna be using these three holes. We're gonna take our spring in, we're gonna go in this hole and we're gonna come out this one. We're gonna take our spacer block, slide it on, thread our carriage bolt onto the spring end of the wire. We'll feed it up, pull it out. We're gonna repeat that for this hole. For this last hole, we're gonna feed our spatial block on our wire, thread the bolt onto the end of the leader, and we're gonna feed the bolt up first, then the spacer block, and then pull your bolt down there. We're gonna repeat that same process on the other side. Next, we're going to feed our wires through the corresponding holes in the hitch. We're gonna to get an extra set of hands to lift our hitch into place. You'll notice there's three holes. We're gonna use the outside two holes here and then this very back one. We're gonna go up over our exhaust on our passenger side. We're gonna raise it up into place. We're gonna take off one of the wires. We're gonna put a nut on each side that'll hold our hitch up while we install our remaining hardware. Once our hitch is held up into place, we're gonna come back. We're gonna put a conical tooth washer on, teeth facing up towards the hitch. We're gonna use that washer to push over on our bolt. That'll put pressure on it so that we can put the nut on without pushing the bolt up into the framer. We're gonna repeat that for all three bolts on each side of the vehicle. Once you have all your hardware installed, we're gonna come back with a 7/8 socket. We're gonna tighten all of our hardware and then torque it to the specification in the instructions. Then we need the trim our heat shield. You'll notice the wide end here. We're gonna be cutting off the skinny side. From this edge, we're gonna go back 11 inches, come straight across, and we're gonna cut off this front half. I'm just gonna use some tin snips to get it cut, and we're gonna take the two nuts that we removed from here and up here and we're gonna install one here and then one here. Next, we need to trim out our underbody panel. From this edge on this corner right here, seven inches up, 32 inches across from this edge. Again, seven inches. Then we're gonna cut out this portion of it. This is usually just a cardboard, probably use a utility knife. Tin snips works as well. Once you have all of your hardware torqued to the specification in your instructions, go ahead and reinstall your exhaust, reinstall your trimmed heat shield, your underbody panel, and you're ready to go. That's gonna do it for a look at an installation of a Draw-Tite Class 3 Trailer Hitch Receiver on 2021 Chrysler Pacifica..

Info for this part was:

Employee Joshua S
Video Edited:
Joshua S
Employee Jacob T
Video Edited:
Jacob T
Employee Chris R
Video Edited:
Chris R
Employee Kathleen M
Video by:
Kathleen M
Employee Jonathan Y
Video by:
Jonathan Y
Employee Randy B
Test Fit:
Randy B
Employee Shane H
Test Fit:
Shane H
Employee Ryan G
Test Fit:
Ryan G

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.