Customers compare C57008 to these similar products
Products Featured in this Video
Clayton: Hello everybody. Clayton here at etrailer.com. Today we're going to be working on a 2017 Ford F-250 that we're going to be taking a look at. And I'll show you how to install the Curt in bed 7-Way for aluminum beds. Now there are a few good reasons that you might want an in bed wiring for your truck in particular. And in our customer's case,… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…
view full answer...The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
view full answer...In regards to the Curt A16 Slider 5th Wheel Trailer Hitch part #C16521 with Adapter Rails for Curt 5th Wheel Hitch part #C88KR, the weight capacity is 16,000 lbs. Therefore, so long as the trailer does not exceed this you'll be fine. If you want…
view full answer...Yes, Demco does have the 21K Autoslide #DM89GV as well as an 18K Autoslide #DM69GV that will fit the factory prep/puck system in a Ram 2500 or 3500 pickup. If you have one of the following pin boxes you will also need the corresponding accessory to…
view full answer...The OEM puck system is optional for Ford pickups so the only way to tell if your 2017 Ford F-250 has the puck system or not is to physically look in the bed for the pucks like what you see in the attached photo. If you do have the puck system then I…
view full answer...To know if your 2017 Ford F-350 has an in-bed puck system installed you'll just need to look and see if you have four rounded attachment points (usually covered up when not in use, like in the attached picture). If you don't see these in your…
view full answer...The Reese Under-Bed Gooseneck Trailer Hitch #RP39FR and the Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches #RP87FR are actually the exact same kit - the Reese 30180 Elite Series Underbed Rail Kit. Both will fit…
view full answer...Hey Roy, There's no real difference between the Curt #C56070-07 and #C57008. The #C56070-07 is just an older kit number that's been redone/replaced with #C57008 and will be eliminated once stock runs out. The #C57008 comes with four…
view full answer...We have everything you need to install a fully functional 7-Way connector and a trailer brake controller on your 2017 Ford Expedition. Since your Expedition is already equipped with a 4-Way connector, you will just need the Universal Wiring Kit…
view full answer...I do have a solution for you but I spoke with my contact at Air Lift and he said that a system like the One Shot cannot be added to the wireless air compressor system #AL74000. There is no way to regulate the air pressure in the tank with the…
view full answer...I have included a diagram that should help when installing an air tank with your Firestone compressor kit on your 2003 Dodge Ram 2500. Basically, it will be similar to the installation of kit #F2168. I have linked its instructions as well which you…
view full answer...When installing the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector part #C57008 you will drill a 7/64" hole at all four of the mounting holes. This is what is stated in the instructions and will be the best practice to…
view full answer...