Best 2015 Chevrolet Colorado Flat Tow Set Up Options

content loading

Customers compare RM-522 to these similar products




Products Featured in this Video



Best 2015 Chevrolet Colorado Flat Tow Set Up Options


Today we'll be taking a look at the Roadmaster Falcon All-Terrain non-binding tow bars as part of a complete flat tow setup for your 2015 Chevrolet Colorado. We'll start with our baseplate, which we'll be using Roadmaster's EZ5 baseplate kit. In addition, we'll be using Roadmaster's diode wiring kit, SMI's Stay-IN-Play DUO supplemental braking system, Roadmaster's battery charge line kit, Roadmaster's automatic battery disconnect switch, Roadmaster's Falcon All-Terrain non-binding tow bars, and lastly, Roadmaster's 64" single-hook safety cables.So you're looking to flat tow your Chevy Colorado We'll we've got our whole setup here, and there's several components we're going to need to complete that. Let's go over those now. The first component you're going to need is your baseplate. This is the interference that's going to allow your vehicle to be connected to your motor home and pulled behind it.

This baseplate is easy to install. You do have to remove the fascia, but there is no drilling required. It replaces your factory tow hooks and is squeezed between the bumper beam. Gonna provide you an attachment point for your safety chains as well as a place to hook up any Roadmaster tow bar. You can hook up other brands using adapters found here on our website.

When not in use, the connection point for your tow bar is removable. Simply pull the pin, twist it, and pull it out. This will give you a more factory appearance.The next component is our diode wiring. This wiring kit allows you to transfer signals from your motor home through the included cable, down to our connector, and to the lights at the back of our vehicle. Our diode wiring's going to connect into both our passenger and drive side taillight assemblies, intercepting the turn and taillight signals.As you can see here, we have our right turn signal, left turn signal, tail lamps, and brake lamps.

The next component is our SMI Stay-IN-Play DUO. That's an electric supplemental braking system. It uses signals from the motor home as well as an inertia sensor to proportionally apply the brake pedal to assist with stopping. The operating unit located under the hood taps into the brake vacuum system and uses air pressure to apply the brake pedal.Our braking system also includes a breakaway switch. This safety device has a cable attached to it, so in the event of a catastrophic disconnect, the pin will get pulled, applying our braking system to help our vehicle come to a safe stop.

When the braking system pulls the pedal, it'll illuminate the LED on the backside of our mirror. This way, we know the system's working properly.While this system is designed for a motor home that has hydraulic brakes, if you have air brakes on your motor home, you can get SMI's Air Force One. It installs fairly similarly but is designed to work with air brakes on your motor home. For our Colorado, we'll also need a battery disconnect. This allows us to disconnect our battery from the vehicle at the touch of a button. Since our vehicle requires the battery to be disconnected when placed into tow mode, this way we can do it quickly and easily.Our wiring just connects to the battery and then to a switch that you'll mount inside your Colorado. Now when we press our button, it'll disconnect our battery. Just press it again, it'll reconnect our battery. We've also installed the battery charge line kit. This'll allow our motor home to charge our battery as we're going down the road. Now even though our battery is disconnected, it is powering our braking system and a few other components. This way, we can ensure when we get to our destination, our battery's going to be charged up and ready for us to start our adventure. We'll attach it to the center post on our six-pole connector, and that way we'll receive our charge from our motor home through this circuit.You've now got all the necessary components installed on your Colorado but you need a way to connect that to the back of your motor home. We're going to be using Falcon's All-Terrain tow bars to do this. As the Falcon All-Terrain is a Roadmaster product, it easily connects to our baseplate that we have installed. The quick-connect arms on our baseplate will easily attach to our Falcon's arms. We slide those down in the slot there. We take the large pin, slide it through both arms, line up the hole on the opposite side, and put the locking pin down in it, making sure to fold it over so it can't become disconnected.Our tow bars are non-binding. This is great because if you're parked on uneven terrain, it can be difficult to disconnect it from your baseplate. You simply pull the lever, and that'll allow the arms to free up, slide in and out, making it easy to get them disconnected. The only thing left is to route your safety cables. The nice thing about the All-Terrain is that it has a channel on each arm to route your wiring and cables through. We simply slide those through, made our connections at our baseplate and at our motor home side, making sure to cross your safety chain cables. Hook up your wiring, which we've also ran through the other arm. So we have our seven-pole on our motor home side and our six-pole on our vehicle side. Then hook up our breakaway switch for our braking system.Depending on your RV, you may need a high-low adapter. You want to be towing as level as possible, and since our RV is so much higher than our vehicle where the baseplate is, we are going to be using a 6" drop here to level that out. Now we can take a look at our Colorado as it's flat-towed behind our motor home. That completes our look at a complete flat tow setup for a Chevrolet Colorado.


Questions and Comments about this Video

What Do You Think?

* e-mail address format: [email protected]

I would like an email notification if someone replies to my comment

Info for this part was:

Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Shane H
Test Fit:
Robert C
Test Fit:
David F
Test Fit:
Ryan G
Video by:
Zack K
Video by:
Kathleen M
Video by:
Alan C
Video by:
Jonathan Y
Video by:
Michael B
Video by:
Jacob H
Video by:
Aidan B
Video Edited:
Andrew K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video Edited:
Mike H
Video Edited:
Dustin K
Video Edited:
Sue W
Video Edited:
Chris R
Video Edited:
Zach D
Installed by:
Cole B
Installed by:
Randy B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.