Customers compare AKIHUB-545-2-1K to these similar products
Products Featured in this Video
Today, we're going to take a look at the pre-greased trailer idler hub assembly for 2,000-pound axles with the five on four-and-a-half inch bolt pattern. Now this idler hub's designed for use on the trailer idler axles. It is designed to fit the 2,000-pound trailer axles that have the BT8 spindles. So it is compatible with standard axles for most manufacturers, including Dexter, Lippert, and… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
It looks like you did your homework Ron, because the Bearing Buddy #BB1980A and the Spindle Grease Seal Set #BB60001 are indeed the proper parts for the #AKIHUB-545-2-1K idler hub assembly. This hub uses the #L44643 inner bearing, so the bearing…
view full answer...To select a set of replacement idler hubs for your Fleetwood Destiny trailer you want to match up a few characteristics from your originals. These include the axle weight capacity, wheel bolt pattern and the bearing set used in the hubs. A…
view full answer...Part 300-020885 refers to an EZ Loader boat trailer BT150/B151 bearing kit. Part #300-020883 refers to a complete 5-on-4-1/2 idler hub kit that includes races, bearings, seal, washers, nut, retainer nut and cotter pin, bearing protector and lug…
view full answer...You can shorten your chain by moving the links in the Buyers Products Weld-On Safety Chain Retainer #3375471000. I have linked our product review video that shows the chain installed on a non-end link of its safety chain.
view full answer...There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…
view full answer...As SnowBear trailers are still being produced, and haven't been around long enough for any of the weird/rare spindle options, you will not need to measure anything else to confirm the fitment of the etrailer.com Trailer Idler Hub Assembly…
view full answer...It sounds like you are looking to replace your hubs. I have attached a link to our trailer hubs where you can use the filters on the page to choose the bolt pattern of your hub, your wheel size, your axle capacity, and since most of our hubs also…
view full answer...The only way to be sure the Trailer Hub Assembly, item #84545UC1-EZ, will fit on your spindle would be to take some measurements or get the bearing and seal part numbers to match up. Since it sounds like you cannot get to the bearings to record part…
view full answer...Before proceeding, I'd take a moment to confirm the spindle diameter, because there are two different bearing sets that are very close in dimension, so you'll want to be absolutely sure of the measurement you get. We recommend using a digital…
view full answer...I believe the Trailer Idler Hub Assembly #AKIHUB-545-2-2K is the correct hub for your Detail K2 Utility Trailer, however it looks like the problem is that the inner cones from the old bearings are stuck to the spindle. Most likely the hub wasn't…
view full answer...Are you sure the diameter of the spindle is 1.25 inches where both bearings ride? That's not typical for a 2,000 lb axle but if instead the diameter is 1.06 inch then you could use the hub part #AKIHUB-545-2-2K which has the 5 on 4-1/2 bolt…
view full answer...The Kenda Loadstar ST175/80D13 Bias Trailer Tire #AM3S120 that you referenced is going to close that trailer frame to tire gap by almost a full inch. This would put the new tire much too close to the frame on your Harbor Freight Trailer. The issue is…
view full answer...