Select the correct transmission cooler by determining where there is enough space to mount it. The diagram on the left numbers the best three positions to mount the transmission cooler in order. Transmission coolers are more efficient when they receive maximum air flow. At Position 1, the transmission cooler is 100% efficient. Position 2, between the air conditioning condenser and radiator, is 75% efficient while Position 3, between the radiator and fan, is only 60% efficient. If positions 2 or 3 are used, a larger transmission cooler will be needed to compensate for the loss of cooling power. If this is the case, choose a transmission cooler that is one or two sizes larger.
Tech Tips: Transmission fluid cannot be over-cooled, but it is critical in extreme cold conditions to allow the vehicle to warm up before driving.
Transmission Coolers Specs:
Features:
It's a simple concept - use the air beneath your vehicle to cool your transmission fluid. With Derale's pan cooler, this process becomes even more effective because of the patented turbulator cooling tubes and large-capacity construction.
Installation Notes:
Designed for vehicles with an A518 (46RH or 46RE), A618 (47RH, 47RE, or 48RE), or A727 (36RH or 37RH) transmission.
If you plan on going off road with your vehicle and will encounter terrain 45° or greater, a filter extender is needed.
More Information >Transmission Coolers Specs:
Features:
It's a simple concept - use the air beneath your vehicle to cool your transmission fluid. With Derale's pan cooler, this process becomes even more effective because of the patented turbulator cooling tubes and large-capacity construction.
Installation Notes:
Designed for vehicles with an A518 (46RH or 46RE), A618 (47RH, 47RE, or 48RE), or A727 (36RH or 37RH) transmission.
If you plan on going off road with your vehicle and will encounter terrain 45° or greater, a filter extender is needed.
More Information >Videos
for Transmission Coolers
Help Articles
for Transmission Coolers
Expert Answers
for Transmission Coolers
You can install a stack cooler in your vehicle. The Class ratings are there as a reference point to a hitch Class. For example if someone has a Class III hitch they can look at coolers, see a Class III and say, hey, I have a Class III hitch so this…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...For a great folding cover for your 2022 Nissan Frontier (short bed), I recommend the BAKFlip MX4 #BAK94AV. The MX4 includes a tri-fold design that lets you access the bed without fully removing the cover. There is also a locking system that creates…
view full answer...Given the weight of your trailer and the fact that you tow uphill I recommend going with the largest cooler or most efficient that will fit in the available space you have in the engine compartment of your 2004 Silverado. A stacked plate cooler is…
view full answer...The Flex-a-lite Transmission Cooler #FLX400117 does come with everything needed to install. No other components would be needed.
view full answer...Currently SuperSprings only offers the rear SuperCoils for your 2019 Ram 1500 2wd. They are available in either a 2,058lb #SSC-50 or 2,480lb #SSC-51 coil capacity. If you plan on keeping the camper on your Ram then go with the higher capacity…
view full answer...When comparing the Flex-a-lite Transmission Cooler #FLX400117 to the similar Derale Series 8000 Transmission Cooler #D13502, there are very few differences between them. Both have an aluminum construction, include all hardware needed, and are…
view full answer...Your 2014 Jeep Grand Cherokee is rated to tow 6,200 lbs as you stated. Your owners manual will state your trailer tongue weight should be approximately 10% of your total trailer weight. Most trailers are 10-15% tongue weight. You will want to make…
view full answer...The method we use to determine the correct line to install a transmission cooler on is pretty simple. You want to install the cooler on the return line. To determine which line is the return line you will want to start with your truck totally…
view full answer...I would start by determining the towing capacity of the vehicle. I did some research, and saw a range of 2000-5200 lbs depending on how the vehicle was equipped. If you phone your Chevy dealer, they should be able to tell you the towing capacity of…
view full answer...To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI