Troubleshooting The Bulldog Powered A-Frame Jack That Does Not Go Down

Question

Question:

My trailer jack will go up but not down

asked by: Yvonne B

0

Expert Reply:

The Bulldog Powered Drive Trailer Jack # BD500199 grounds through the mounting hardware. I would recommend running a jumper wire from the mounting flange of the jack to the ground wire on your trailer wiring to see if you can get it to work that way. The jack has an internal circuit breaker that automatically resets so the only other problem it could be is an internal problem. If that is the case you will have to purchase a new jack.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

If you already have a seal that you're replacing then you want to get a seal that's a similar size, otherwise if it's a brand new application then I recommend trying to find the depth of the gap and choosing a seal slightly taller since…

view full answer...

Answer 2

I do have an option for you but the handles included with the Cam-Action Lockable Door Latch Kits like part #PLR658-SSP must be welded to the pole as there are no other options to attach them. If you can get away with a 55" long pipe then you…

view full answer...

Answer 3

If it's the drop leg like #BD500190 that's bent, you certainly can replace it if it's not bent to the point where you can pull the pin and slide the drop leg out. The #BD500190 would be the proper replacement for a Bulldog #BD500185,…

view full answer...

Answer 4

There is no reason why you could not turn the jack at a 90 degree angle to gain more clearance. Due to the configuration of the holes in the mounting flange, you might need to drill new holes in your trailer tongue to mount the jack in that…

view full answer...

Answer 5

According to the details you told me, it sounds like you are running the Powered Drive Trailer Jack #BD500199 off of a battery on the trailer. Does the problem you describe always occur when the jack as at a particular height? If so, the jack tube…

view full answer...

Answer 6

The closest thing we have to a 2" x 2" bumper is the Rubber Bumper for Enclosed Trailer Ramp Door #37210715 you looked at. This has a 2-1/2" diameter with a height of 1" and a 3/8" mounting hole.

view full answer...

Answer 7

In the image with the suspension setup the equalizer #TREQ105 is placed between the front and second axles. Just like you have on your trailer. The front of the equalizer connects to the spring using a shackle strap and the rear is connected directly…

view full answer...

Answer 8

The Rubber Ribbed Hollow Bulb Seal for RV and Trailer Doors #SR76ZR is designed exactly for this purpose so you'll be good to go with it. When you install the sides you'll want to cut a small portion of the bulb away while still leaving the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Troubleshooting The Bulldog Powered A-Frame Jack That Does Not Go Down

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching