Weight of Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar

Question

Question:

How much does the Rhino T load hitch itself weigh?

asked by: Peterr G

1

Helpful Expert Reply:

The Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar for 2" Hitches # RTL002 has a shipping weight of 43 lbs so you're looking at about 40 lbs once the packaging is removed.

expert reply by: Jon G

1

Answer 1

The adjustable height range of the Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar for 2" Hitches - 49" Long #RTL002 is 42-64 inches high. In order to make sure that the Rhino-Rack T-Load will clear your camper shell and reach…

view full answer...

Answer 2

As you can see in the diagram I provided, the tilt is adjustable up to about 45°. The tilt mechanism has a pin that can be used in two different positions to allow a roughly 15 or 30° degree tilt or the pin can be completely removed for the…

view full answer...

Answer 3

To find out if the Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar RTL002 will fit beyond the spare tire on your 2010 Toyota FJ Cruiser, there is a simple measurement you can take. Holding a straight edge (like a yardstick) against the…

view full answer...

Answer 4

The Draw-Tite Front Mount Trailer Hitch Receiver part #65076 fits all models of the 2020 Ford F-250 Super Duty without interfering with the front axle.The front mount hitch will work well to use a load extender to carry the canoe. I recommend the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hello Carol, welcome back. It is possible to use the Yakima HD Crossbars #Y01157 on your 2025 Subaru Outback Wilderness with the fixed raised bars. What you will need is the TimberLine Towers #Y33TR and the HD Bar Adapter #Y03541 to complete this…

view full answer...

Answer 7

Yes! You can use both a kayak rack and a truck bed extender on your 2021 Jeep Gladiator with the Trail Rail system. Since the Access Lorado Soft, Roll-Up Tonneau Cover #A53VR leaves the stake pockets completely open, you will be able to install a way…

view full answer...

Answer 8

Hey Deb, You could just remove the load stops for the Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar #RTL002 and clamp on one kayak carrier like the Rhino-Rack Kayak Roof Rack w/ Tie-Downs #S512-S512X to the crossbar and the other to the…

view full answer...

Answer 9

Because of the overhang from a 5th wheel trailer the best solution for transporting a couple of kayaks while towing is with the combination of a single bar rack for the cab and a front-mounted load extender that installs into a front-mount hitch. For…

view full answer...

Answer 10

Geoff, the wheel bearings for the Yakima Rack N Roll is not available for replacement, unfortunately. To replace the bearings you'd need to replace the entire wheel with the Replacement Wheels for Yakima Rack and Roll Trailer #8880157, which…

view full answer...

Answer 11

We have T-slot adapters for Thule cargo boxes with the part #TH27PQ and Inno boxes with the part #INBRP12 but at this time Yakima does not offer any adapters like this. I attached a link to this page that shows all of the Inno boxes we offer as well…

view full answer...

Answer 12

The main difference between the Lockrack Adjustable XL Watersport Carrier #LR54FR & the Lockrack Adjustable Watersport Carrier #LR24VR is going to be the adjustable base range. The #LR24VR has an adjustable base range of 19-11/16" to…

view full answer...

Weight of Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching