Will the a Tire on Bumper Mount Spare Tire Carrier # TR-1 Clear Trailer Hitch on a 1985 Chevy C3500
Question:
I want to remove the tire carrier from the rear wall of my RV and mount to the bumper. My question is wil the tire with wheel cover installed clear the receiver hitch mounted under the rear bumper or do you have something that is a little taller? This is going on an 84 Chevy C3500 class C Mallard motor home.
asked by: Ronald H
Expert Reply:
That is tough to answer but I think I know how you can figure it out. Take a look at the picture I have included. It has the overall height of carrier # TR-1. From the bottom of the bumper, measure up approximately 15 inches, this is about where the center of the top wheel bracket will be. Then take half the diameter of the tire and measure back down to see roughly where the bottom of the tire will be. This is all approximate but it is a good start.
Another option, if you will not be using the trailer hitch receiver, is to use the Curt spare tire carrier, # C31006.
And yet a third option is to use the Curt carrier with dual purpose ball mount # D210 if you will be towing a trailer. However, when I asked Curt is this was permissible they said that it is but they highly recommend using an anti-rattle device in the top receiver, like # 63232, and a stabilization strap # 18050.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Trailer Hitch Lock
- Universal Anti-Rattle Lock
- Keyed Unique
- Fits 2 Inch Hitch
- Spring-Loaded Pin
- 3-1/2 Inch Span
- Lets Go Aero
more information >
Curt Trailer Hitch Spare Tire Mount
- Spare Tire Carrier
- Hitch Mount
- Universal
- Car
- SUV
- Trailer
- Truck
- Van
- CURT
more information >
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Built-In Dual Hitch
- CURT
more information >
Product Page this Question was Asked From
Bumper Spare Tire Mount - U-Bolt Mount
- Spare Tire Carrier
- Bumper Mount
- 5-Bolt
- 6-Bolt
- 8-Bolt
- RV
- Stromberg Carlson
more information >
Continue Researching
- Article: Trailer Tire Sizing
- Article: How to Measure the Bolt Pattern of a Trailer Wheel
- Q&A: Spare Tire & Wheel For 2023 Coleman Lantern 17B
- Q&A: Recommended White Spare Tire Cover for a 26" Diameter Tire
- Q&A: Backspacing of Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Black Mod Wheel # AM31990
- Q&A: Is There A Way To Secure The Front Two Panels Of The BAKFlip G2 Open While Driving
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Q&A: How To Get The Brake Light Switch Signal In A 2023 Ford Bronco
- Article: How to Accurately Measure Trailer Leaf Springs
- Q&A: Will Using a 2-1/2" to 2" Reducer Reduce The Towing Capacity For a 2022 GMC Sierra 3500?
- Q&A: Which Stromberg Carlson Bumper Mounted Tire Carrier Should I Use, # TR-1 or TR-2
- Article: Trailer Wiring Diagrams
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: How (and Where) to Connect an RV Propane Grill