Brake Assemblies that Fit Hayes 7k Brake Assemblies with 4-Bolt Mounting Pattern

Question

Question:

old hayes 12x2 7k 4 bolt mount . i see the 23-105-09 but they are rated at 6K. is there anything else?

asked by: Keith A

0

Expert Reply:

The # 23-105-09 would work well since the dimensions and bolt pattern are correct for your Hayes 7k setup. Typically brake assemblies in this size will have weight ratings that range from 5,200 up to 7k so the # 23-105-09 will work well as they match size and bolt pattern.

expert reply by: Jameson C

0

Answer 1

If your current brake assemblies have a 4-bolt mounting pattern then you likely need the Nev-R-Adjust Brake Kit #23-468-469 (10") for 3,500 lb axles. Since the Brake Kit #23-464-465 (12") that you referenced has a 5-bolt mounting pattern it…

view full answer...

Answer 2

I attached a picture that has the bolt pattern of the brake assemblies part #23-105-106-09 that you mentioned. This is the standard offset AL-Ko style of 4 bolt pattern.

view full answer...

Answer 3

For your 12x2 electric brake assemblies, I recommend the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange - 12" - Left/Right Hand Assemblies #23-105-106-09. These assemblies will fit your 4 bolt flange and will work well on your trailer.…

view full answer...

Answer 4

The Dexter Braking Assemblies like the #23-464-465 are widely regarded as the highest quality assemblies due to them being manufactured right here in the USA and using the highest quality materials available. With that said we have sold a lot of the…

view full answer...

Answer 5

When it comes to brakes for your boss's older Flying L gooseneck horse trailer, I believe that I have exactly what you are looking for, #23-105-09 and #23-106-09 for a 6,000 lb axle. I have included a picture which includes the mounting hole…

view full answer...

Answer 6

Most likely the #23-105-09 and #23-106-09 would work well for you, but you need to verify one more thing. Does the current brake assembly you have attach to the axle with 5 nuts? If so, then you have the standard bolt mounting pattern these two would…

view full answer...

Answer 7

We do offer 12 x 2-inch electric brake assemblies with a 4-bolt mounting flange. Dexter parts #23-106-09 and #23-105-09 are right- and left-hand brake assemblies that have dual mounting hole patterns, both 5-hole and 4-hole. These brakes are rated…

view full answer...

Answer 8

We do stock all types of replacement parts for electric drum brakes like the 12-inch Dexter 6K brakes #23-105-09 (left) and #23-106-09 (right). These items are not kitted together but you can see each item we have, from magnets to brake shoes to…

view full answer...

Answer 9

The Dexter brake assemblies part #23-105-106-09 can mount to the AL KO 4 bolt mounting flange. If the upper mounting bolt holes are further apart than the lower bolt holes these assemblies will fit and work well.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Brake Assemblies that Fit Hayes 7k Brake Assemblies with 4-Bolt Mounting Pattern

Product Page this Question was Asked From

Continue Researching