Can Lippert Motor be Used to Replace Atwood Landing Gear and Motor 75721

Question

Question:

I was told by Liebert and stromberg-carlson that their motor and gearbox is will not work on Atwood. Can you explain your claim of that they will

asked by: Sam A

0

Expert Reply:

I reached out to my contact at Lippert who said that replacing the motor alone with a Lippert motor like part # LG-142178 or # LC141893 wouldn't work but if you replaced your Atwood gearbox with the Replacement Gearbox # LC276602 then you can definitely keep your current landing gear legs. I'm not sure who you spoke with at Lippert but this is something that we've been told by them for a while now and I called them again just to make sure that nothing had changed (and it hadn't).

expert reply by: Jon G

0

Answer 1

We've checked in the past and have been told the only current landing gear motor that can be used with your Atwood setup is the part #LG-142178 which even having a lower capacity will still do a great job. The jack motor doesn't support the…

view full answer...

Answer 2

Thanks for reaching out! While we don't carry that specific brand, there are some common operations between dual two-stage regulators so I'll be able to shed some light onto the subject for you. When using a two-propane tank setup you'll…

view full answer...

Answer 3

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 4

The price difference does seem backwards, but the faster speed part #LG-141893 has the same weight capacity as the lower speed part #LG-142178 that you also referenced. It's a difference of 5,500 RPM and 7,140 RPM so you would definitely see a…

view full answer...

Answer 5

To replace the motor on your Atwood landing gear, I recommend the Stromberg Carlson Replacement Motor #LG-142178. This is a fairly universal landing gear motor that is designed for use with Stromberg Carlson landing gear systems, but can also be used…

view full answer...

Answer 6

If the replacing the gear box didn't fix the problem, then as long as the internals of the legs themselves are still in good shape replacing the motor would be the next logical step. Before doing that, I'd use the crank to operate the landing…

view full answer...

Answer 7

Thank you for the pictures and information provided. While the Atwood 75721 motor and gear boxes are discontinued, we do have a gear box that will work with your Atwood 75721 motor and landing gear. - Replacement Gearbox for Venture Aluminum Electric…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Can Lippert Motor be Used to Replace Atwood Landing Gear and Motor 75721

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching