What is the Correct trailer Ball Size to Work With the Draw-Tite # 36061 Drawbar

Question

Question:

Just to confirm - Im ordering drawbar 36061 and want to confirm that hitch ball 19256 fits that. Im towing a small tent trailer, 1300 gvw, with a Mercury voyager.

asked by: Mark

0

Expert Reply:

Yes, the # 19256 Hitch Ball has a 3/4 of an inch thread shank.

This ball will work with the Draw-Tite Class II Drawbar, # 36061.

expert reply by: Jared P

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 7

Hello Paul, thanks for reaching out. The inside dimension of the Curt Heavy-Duty Dual Ball Attachment for Weight Distribution Shanks #C29NR is 2". It will work with any standard weight distribution shank. I edited a picture to illustrate.

view full answer...

Answer 8

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 9

Hey James! The individual balls can not be removed on the BulletProof Hitches Aluminum Adjustable 2-Ball Mount item #BPH47MR. The platform they are mounted on can be removed by taking the pins out holding it to the shank but the balls are permanently…

view full answer...

Answer 10

Hey Carl! How much does the Weigh Safe weigh? With all of the parts put together the #WS88RR weighs 35-1/2 lbs. If you need anything else don't hesitate to reach out in the comments below.

view full answer...

Answer 11

Hey Josh! Yes, you can lock the BulletProof Hitches Aluminum Adjustable 2-Ball Mount #BPH97MR to your hitch receiver by using the Locking Kit #BPH34FR. This comes with a lock for the hitch receiver as well as the adjustable part of the platform so…

view full answer...

Answer 12

Hey Mike! To answer your first question yes, the Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter #RP59KR can replace the Curt Helux. This is compatible with the Rhino bolt pattern which is the same thing the Helux fits. I don't…

view full answer...

What is the Correct trailer Ball Size to Work With the Draw-Tite # 36061 Drawbar

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching