How Does Breakaway Cable of Titan Actuator Reset

Question

Question:

If the acuator has be set can it be rest or do you have to replace it

asked by: Greg

0

Expert Reply:

What do you mean reset? Do you mean like resetting the breakaway mechanism of the actuator?

To release the breakaway lever of the Titan Zinc-Plated Brake Actuator # T4747200 you will need to use a screw driver to push the clip on the lever back towards the rear of the trailer while pushing the lever back to its original position.

expert reply by: Jameson C

0

Answer 1

I just called my contact at Titan and they told me that you should never use the DOT 5 fluid. They said if DOT 5 is used it will reduce the life of the seals in the unit by about 75 percent. They told me that DOT lll brake fluid should be used.

view full answer...

Answer 2

Yes, the Replacement Solenoid Valve, #T4748800, will fit the Model 60 Titan Actuator. We have learned that in order to attach this solenoid to the master cylinder, the fitting that is currently on the master cylinder will need to be removed and the…

view full answer...

Answer 3

I spoke to my contact at Titan about resetting a Titan Model 60 actuator which is not the Dexter part #099-175-20. You have to remove the cover and then carefully remove the spring inside. Then set the lever in the disengaged position and re-insert…

view full answer...

Answer 4

I have attached an install video to this page for you to check out that you can use as a guide for installing the Titan Model 60 actuator part #T43397007K that you referenced. The video shows a very similar Demco coupler part #DM72VR but the couplers…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 9

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

Hey Mike, thanks for reaching out! It sounds like your 2025 Toyota Sienna doesn't have any wiring at the back so you'll need to install the T-One Wiring Harness #TK69FR along with the Universal Wiring Kit #ETBC7. This will give you all of the…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How Does Breakaway Cable of Titan Actuator Reset

Product Page this Question was Asked From

Continue Researching