bing tracking image
  1. Camper Jacks
  2. Ultra-Fab Products
  3. Stabilizer Jacks
  4. Fifth Wheel Camper
  5. Travel Trailer
  6. Electric Jack
Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs

Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs

Item # UF39-941704
Our Price: $657.50
Camper Jacks
Add to cart
In Stock
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

Videos

Need help with installation?
Locate installers near me
Stabilize and level your travel or 5th-wheel trailer with this unique device. Designed to span the width of your rig for maximum support, the opposing sides of this stabilizer can be adjusted independently for effective leveling. 1-800-940-8924 to order Ultra-Fab Products camper jacks part number UF39-941704 or order online at etrailer.com. Free expert support on all Ultra-Fab Products products. Great prices and Fastest Shipping for Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs. Camper Jacks reviews from real customers.
  • All Info
  • Reviews (87)
  • Q & A (0)
  • Videos (1)
  • Photos

Ultra-Fab Products Camper Jacks - UF39-941704

  • Stabilizer Jacks
  • Fifth Wheel Camper
  • Travel Trailer
  • Electric Jack
  • 5001 - 6000 lbs
  • 1 Jack
  • 30 Inch Lift
  • Bolt-On
  • Ultra-Fab Products
  • Steel

Stabilize and level your travel or 5th-wheel trailer with this unique device. Designed to span the width of your rig for maximum support, the opposing sides of this stabilizer can be adjusted independently for effective leveling.


Features:

  • Cross-frame-mount jack stops front-to-back and side-to-side motion of travel or 5th-wheel trailer
    • Provides support across the width of your motor home or trailer
      • Not recommended for use on front of motorized vehicle
    • Stabilizes with wide side support brackets
  • Connecting bracket holds sides of stabilizer together and provides additional support
    • Adjusts to fit the width of your trailer or RV
  • Extra-large footplates help to minimize sinking and tilting
  • Hand crank attaches for manual operation
  • Sturdy steel construction


Specs:

  • Application: trailers and RVs with frames from 48" to 80" wide
  • Lift: 30"
  • Bracket width: 36"
  • Weight capacity: 6,000 lbs
  • 3-Year warranty


39-941704 UltraFab PT II Manual Stabilizer

Installation Details UF39-941704 Installation instructions



Video of Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Ultra-Fab Trailers and RV Power Twin II Manual Stabilizer Review

Hey guys, it's Randy here at etrailer.com. Now, one of the most common problems when you're out camping, whether it's going to be a travel trailer, a fifth-wheel camper, whatever you've got, is the movement that can be felt inside of the camper when you're either trying to relax and watch a movie and the kids are playing around in the back. You just feel that shifting forward and back. Or maybe some people decided to go to sleep and a few people decided to stay up around the bonfire. It happens just about every camping trip I go on. Then you're trying to sneak into the camper, you're trying to kind of ease your way in.

It just makes it pretty difficult. You don't want to wake up the people that went to bed early. Maybe they're going out on a fishing trip, maybe they're going on a hike. You don't want to disrupt that, but you want to enjoy your time too.Basically what we're looking at today is from Ultra-Fab. This is their Twin Stabilizer system.

This is the manual, so no power required, no wires to run. There's really nothing you have to do except for level out your camper and deploy your stabilizers. Now, when we compare these to regular scissor jacks, these are significantly better. You can look through customer reviews, the different things they say. It's crazy how big of a difference there is.

Basically, generally your stabilizer jacks are going to be mounted on a 45-degree angle or maybe straight out from your camper. You get your standard tool and you go down there and you crank them out. But they don't offer a whole lot of front to back or side to side stability. They just keep that tilting to a minimum.When we use something like this, we're going to attach this portion directly to the frame of our camper. That gives us excellent side to side stability, but you notice they're also angled in.

This triangulation prevents this leg from being able to move forward and back so it gives us much, much more stability. Again, looking through the reviews, customers always say, "I wish I would have known about these sooner." "I wish I would've had these sooner." "They make a world of difference." Even on larger campers like your fifth-wheel campers, people say it takes 90 to 95% of that movement out. Overall, your enjoyment level's going to go up. You're not going to be sitting in there and getting seasick because your kids are fighting in the front. I think it's going to be an excellent solution for you and it's designed to fit a wide variety of applications.We can go all the way down to a 48-inch frame width all all the way out to an 80-inch frame width. All of that adjustment happens right here in the middle. You can see we've got a two-piece design, so we've got one that we'll put on either the driver or passenger side, the other piece goes on the opposite side, and they're tied together right here in the middle with this connection plate. You can see all the holes we have to choose from, also several holes on the actual arms here themselves, and they're designed to slide beside each other. You see this one's mounted here, this one's mounted here, so these are completely independently adjustable. Once we get them where we want it matched up to our frame size, we're never going to have to worry about adjusting this again. It's going to come with all the hardware you need to assemble the stabilizers. The only thing that you'll have to pick is what you want to use to attach it to the frame of your camper.You do have six holes here, half inch or three eighths bolts should go through there without any kind of issues, but also you can see some of the smaller holes that we have here. In those you could use some #14 self-tapping screws. Just make sure you get enough of them in there and you run them through your frame properly so you got the support you need.Now, the stabilizers are going to give you 6,000 pounds of capacity. One thing you want to keep in mind though with a stabilizer system like this, it's not used for leveling your camper. You need to get your camper level. Once it's level, we'll take our tool, we'll bring our stabilizers down until they make contact, just give it another crank or two. That's going to give us good support. It's going to take a little bit of that strain off, but we're certainly not going to use these to level our camper. There's available from Lippert the Ground Control TT or the Ground Control 3.0 system. That's an excellent option if you're looking for leveling and stabilization, but it's certainly a much more expensive system as well.You see, it's pretty easy operation going up or down. Now of course, the way we've got it set up here with it not being mounted to a camper, this is moving up and down, but with this being attached to your frame, that leg comes up and down. The tool is nice and long, so even if you do have a slight overhang here coming out to the side you'll be able to get to it and operate it without any kind of issues.Now, we've got a total of 30 inches of travel. Best way to know if these are going to work for your application, make sure the outside to outside of your frame is somewhere between 48 and 80 and make sure in any of your camping situations that from the bottom of your frame down to the ground it's not more than about 28 inches. That should be perfect. Let's say it was 32 or 33 inches. You could always use a few of the Ultra- Fab stackers underneath each leg. That'll give you the clearance you need and still provide you the list, so that's an option, and I also like how they're independently adjustable. We're going to have a screw in here and a screw in here, so even if we are on an unlevel kind of a camping surface, kind of like what we've simulated here, it'll be about five and a half inches difference from side to side. You can still see that we maintain perfect level and as we lift that up it's going to support our camper and it's going to keep us nice and stable.Now, the overall construction is really nice and heavy duty, probably as heavy duty as I've seen on any of these stabilizer systems, especially a little more heavy than what we see out of the Lippert. We've also got a nice large footplate down here. You can see that's got the clear zinc finish on it. That's going to help prevent any rust or any corrosion or anything like that, and all of this steel, it has a black powder coat finish on it. So again, rust and corrosion shouldn't be an issue. Several customers reviewed this after a year of use and said it still looks great. The finish still holds up really well and they're really happy with it.Now, just to give you an idea of the dimension and how large this footplate really is. You can see it's six and a half inches wide. It's going to be eight inches long. That does an excellent job of dissipating that energy out over a greater area and it's drastically going to reduce the amount of sinkage that we get, especially when we compare these to just a standard scissor jet.Now guys, I really feel like this is going to improve your camping situation. I've installed these on several different campers and I really like the way they work and the felt effect that you get is pretty phenomenal. I think you're really going to enjoy it. Now, you might say, "I don't want to crank on them." You've got no need in the world for that, I want to hit some buttons. You can go with the other option from Ultra-Fab. It already has the motors installed and you're going to have your switches. The thing I like about this one, we don't have to run any wires. We don't have to worry about if our battery's dead or something like that. We get out there and we crank them up, but I do understand sometimes you want a little bit more convenience, you want to be a little bit more easy, just hit a couple buttons, get everything taken care of.

Customer Satisfaction Score:


Customer Reviews

Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs - UF39-941704

Average Customer Rating:  4.5 out of 5 stars   (87 Customer Reviews)

Stabilize and level your travel or 5th-wheel trailer with this unique device. Designed to span the width of your rig for maximum support, the opposing sides of this stabilizer can be adjusted independently for effective leveling.

by:

If you are looking for "stabilizers" that are strong enough to handle heavy trailers this is the unit for you. A little inconvenient because of the independent screws but they will lift the weight indicated which is why the stabilizers are in quotations.



by:

This product is awesome and has made a substantial difference in the stability of our camper! We have a 32' travel trailer and the factory jacks are sad and could feel every movement of the kids. This has taken away 90% of the movement that we were having before.
If you are not handy plan on having someone install this for you. It's not hard to do but if you don't have some tools for the job you will struggle. It took about 4 hours total to install.



by:

Very happy with the quality of this stabilizer jack!! I currently only have the jack installed on one end of our toy hauler and you can feel the difference in how stable the camper is on one end compared to the other end that still has the scissor type jacks. I will definitely be purchasing a second one!!

Brian S.

8/5/2017

I did end up purchasing a second set of these stabilizer jacks a few weeks later and Im very happy I did!!



by:

Helpful hint: Have in home position before tightening all the bolts. Best stabilizer I have found out there.



by:

Product was delivered on time, no problem with assembly I do wish the instructions where larger but went on line and printed it off, well built no problem on install good product



by:

It is awesome!
It does not come with
hardware to mount to the frame and I had to fabricate a bit to make it fit around a support beam.



by:



by:



by:



by:

Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.



by:

These jacks are quality built and held up for a 3 month trip to Alaska. I choose to weld the two halves together to minimize the offset. The heavy material made it easy and very sturdy. The system is powerful enough to lift rear of our RV unit partially off the ground but you need to be careful to support the axles so you don't twist the frame on light trailers.



by:

Overall the service was excellent. The product is top quality. There were a couple problems with shipping but Ashley was more than helpful in resolving them. Thanks to all the folks at etrailer.



by:

I love these stabilizers. I wish this size was sold without the motors. One of the motors started operating on its own so I took the motors off and manually set them. They will stop a lot of movement when walking around in your camper. I highly recommend them.



by:

I ordered 2 of these units. I give UPS 1 star because they lost an entire unit so I called etrailer and I give them 5 stars for immediately shipping a third unit. Then the first unit arrived from UPS and they lost the motors and hardware kit. I called etrailer and they are shipping more motors and the hardware kit. Hoping UPS doesn’t lose the parts for the replacements! The photo shows all I received so far for two full kits.



by:

Installed on a 2018 E350 Ford Minnie Winnie. The package arrived really beat up but only a single cover was damaged. It was replaced quickly. Nothing was missing.

I had to shim it down from the frame about 1.5 inches using a bar of 1.5"x3"x 24" inch aluminum stock on each side. Then it would clear the fuel tank and the gray water.

Switches are installed in our garage under the bed. Wiring came from power panel which is fairly close to the switches so it all went fairly well. Wire nuts are not recommended so I had to hunt around to find connectors that would work.

I have not used it for camping so do not how well it will work to stabilize the vehicle. We do a lot of boon docking so will have to have some good blocking to level and stabilize. It feels a little better sitting on the street. I do wish there was a lockout for them being raised before moving the vehicle outside of PARK?



by:

It looks like a great product am anxious to install them.
I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate



by:

Very pleased. Not that hard to install. These replace the weak stabilizers that came with the trailer. You'll need a jack and an electrical kit to complete the install.



by:

I finished the assembly and install of the power twin II stabilizer and have included pictures of the install. This is a good quality unit and I am very happy with how it works.

Bob



by:

Would have been nice to know that it didn't fit my Grand Design Imagine 22MLE without some "frame modifications", and over $xxxx in installation costs.

Warning to new buyers; DO SOME REAL CLOSE MEASURING TO MAKE SURE THE SYSTEM
WILL FIT BETWEEN ALL ATTACHED HARDWARE, LIKE DUMP VALVES AND DROP FRAMES! any modifications will cost you dearly.

Electric motors are very slow, seems like it takes forever to drop each foot.

BUT----------They do work.



by:

After installation the stability or my toy hauler was increased X3. The installation was relatively easy and all that was needed was common tools and a floor jack. Wiring was covered by simple easy to follow instruction. Some shrink wrap and a solder gun make permanent water resistant connections which I recommend.



by:

I got the jack for three reasons. My original jack was intermittent, it was bent and it did not level the trailer because it had only one motor. The new jack works great and it can level the trailer because it has two motors and the power required. It was not the easiest to install because of the increased size and it will not level the trailer if it is off more that 2 inches or so side to side. In spite of these drawbacks and the fact it added weight to the rear of the trailer I am very happy with the new jack.



by:

Little intimidating at first, just took my time and it went together without any major problem. The problem that I had was dealt with quickly. It's solid and well built. Print on the instructions was a little small for my eyes. Having the instructions on line was a great help.



by:

The Jacks are considerably more durable well built compared to the Lippert models. The lifting power is real and once on the ground the prevent movement of the RV by orders of magnitude over the other style jacks. I only have one in the center of a long trailer and it has stopped the bouncing and side to side swaying of the trailer. Just stepping onto the stairs to get in its rock solid. Also when all the legs are deployed the doors close way better than they ever had with just the Lippert jacks on the front and back. Definitely recommend to anyone thinking about a better jack than what's provided oem.



by:

I received the leveller/stabilizer as expected. The instructions for installation were clear and I found it easy to assemble and install them. Wiring was a bit tricky because of my trailer design, but worked out fine in the end. I have just returned from a three week trip and can recommend this product whole heartedly. One thought I have had is that a manual version might be satisfactory, using a drill to drive the gears until they engage with the ground, and then using a manual crank after that. The motors are a bit slow to drop the feet to the ground because they also have the necessary torque and gear ratios to lift the corner of the trailer. All in all, a great product.



by:

The stabilizer was a great purchase. It has lived up to it’s description as advertised. I did have to make some alterations. Because I have a slide out carrying rack on my 2010 Cougar 5th wheel, I had to weld the stabilizer to the frame so I could use the slide out rack. It works great. I highly recommend the product.


25
87
Show More Reviews

See what our Experts say about this Ultra-Fab Products Camper Jacks

  • What Is The Length Of The Ultra-Fab Twin II Stabilizer Mounting Bracket
    The mounting bracket for the Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704 is approximately 35-3/8" in length. The frame height would dictate the amount of lift you would want but there are other factors to take into account. The placement of the stabilizer could lead you running into clearance issues when going up or down a steep hill so if you'd prefer to have as much clearance as possible then you'd go with the 22" # UF39-941707. The trade off is that you'd most likely have...
    view full answer...
  • Will Replacement Manual Hand Crank for Ultra-Fab Twin II Stabilizer Fit Split Shaft
    Yes, the Replacement Manual Hand Crank for Ultra-Fab Twin II Stabilizer # UF39-84-1641 has the pin in the socket on the end so it will be able to turn the shaft on the # UF39-941704.
    view full answer...
  • How Much Will Ultra-Fab Power Twin II Stabilizer Reduce Ground Clearance
    The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 measures 5" from the trailer frame to the lowest hanging part of the jack. I confirmed this with my contact at Ultra-Fab. Since your trailer has a lower profile it might be better if you used the 22" lift version # UF39-941707 instead. This only comes with the electric motor (which makes operation easier) but since the legs will be able to extend out lower their weight rating will be higher. This measures...
    view full answer...
    Image 1 for Image 2 for
  • Could Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704 Fit Frame Width 67-1/8"
    The Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704 that you referenced fits trailers that have frames that are 48 to 80 inches wide. Since you measured 67-1/8 inches wide this would easily fit your trailer.
    view full answer...
  • Can Ultra-Fab Stabilizers Be Mounted to the A Part of an A-Frame Trailer
    The Ultra-Fab Power Twin II Manual Stabilizer, # UF39-941704, and similar products would have to be mounted just back from the A-frame part of the frame. They are meant to provide support and not lift the trailer so you would not need this type of item on the A-frame. The regular trailer jack or even some scissor jacks # UF48-979002 if needed would be the way to go.
    view full answer...
  • Can Spacers Be Used With The Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704
    The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 needs to attach directly to the frame of your trailer so I recommend either sliding the stabilizer over a bit on the frame to clear the gas line or to reroute the gas line around where the stabilizer will mount.
    view full answer...
  • Do Bolts of Ultra Fab Power Twin Stabilizer Jack Interfere with Bracket Mounting Flush to Frame
    I spoke with our contact at Ultra Fab and the bolts are upside down in our product pictures of the # UF39-941704 that you referenced. When they are installed properly they would not interfere with the mounting surface.
    view full answer...
    Image 1 for
  • Does The Ultra-Fab Power Twin II Manual Stabilizer Come With Spacer Blocks
    If you're talking about a space to sit between the mounting brackets of the Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704 and the frame of the trailer then no, this stabilizer does not have spacers. If you're trying to gain more clearance you could have a welder add in a spacer to the frame with some metal tubing but would need to ensure that tube is rated high enough to handle the pressure of the jack pushing against it. You could then use some self-tapping bolts with some Loctite...
    view full answer...
  • Can You Get the Lippert Electric Stabilizer Jack Without the Motor?
    The Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 or # LC369774 only come with the motor. You can get a replacement motor and replacement arms but the main support beam and legs are not replacement parts available. If you want a similar style jack without a motor you can use the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704.
    view full answer...
  • Will Ultra-Fab Power Twin II Manual Stabilizer Fit a 2003 Keystone Cougar 5th Wheel Trailer
    The frame width on your 2003 Keystone Cougar 5th wheel trailer will need to be between 48 and 80 inches (measured from the outside of the frame on one side to the outside of the frame on the other side) in order for the Ultra-Fab Power Twin II Manual Stabilizer, # UF39-941704, to fit. The stabilizer has L-shaped brackets that fit on the frame and will be bolted into place. It is a straight forward installation and the average do-it-yourselfer should have no problem performing the installation....
    view full answer...
  • How do the Ultra-Fab Stabilizer Jack Attach to RVs
    The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 that you referenced is designed to be bolted on with the included mounting hardware. The difference between the # UF39-941704 and the # UF39-941705 is that the # UF39-941705 comes with dual 12 volt motors to raise and lower the legs of the stabilizer jacks. Whereas, the # UF39-941704 that you referenced require manual operation that includes cranking a jack handle.
    view full answer...
  • Replacement Stabilizer Jack System for 2021 Jayco Jay Flight Travel Trailer
    The best option from Lippert is the Lippert High-Speed Power Stabilizer Jack, # LC298707. But in this style of stabilizers, I prefer the Ultra-Fab products, they have the Power Twin II Electric Stabilizers with Dual Motors, use # UF39-941705 for a 30" lift and # UF39-941707 for 22". See the product pages for specs and application of which is best for your trailers frame width and spacing. The Ultra-Fab Power Twin II has dual 12V motors that function independently for quick, simple leveling....
    view full answer...
  • Recommendations for Manual Stabilizer Jack with 22 Inches of Lift
    There isn't a manual version of the Ultra_Fab Power Twin stabilizer jack with 22 inches of lift but I do have some options for you. You can use Valterra Folding Manual Stabilizer for Trailers and RVs - 14" to 28" Tall - Aluminum Item # 020106 which uses a ratchet strap to raise/lower the legs. It would have to be placed in an easy to reach location though. Another option is to go with scissor jacks such as # UF48-979031. If you do go with these scissor jacks you can add Ultra-Fab Speed...
    view full answer...
  • Can Ultra-Fab Stabilizer Jack be Used at Rear of Trailer
    Yes, the Ultra-Fab Power Twin II Stabilizer # UF39-941704 can be used at the rear of your trailer. It's designed to fit trailer's with frames from 48 to 80 inches wide and has a lift of 30 inches.
    view full answer...
  • Availability of Ultra Fab Stabilizer Jack that is Manually Operated
    We have the part # UF39-941704 which is a manual operated stabilizer jack similar to the part # UF39-941704 that you referenced.
    view full answer...
  • Recommended Best Stabilizer System for 2018 Grand Design Reflection 28BH
    Your 2018 Grand Design 28bh, the JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs # LC191023 can work. Another alternative is to use a stabilizer like the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704 or an electric stabilizer like # LC369774. I recommend the Lippert Electric Stabilizer as the best option for you 2018 Grand Design.
    view full answer...
  • Dimensions of Motor and Gear Box of Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707
    I attached a picture that shows the dimensions of just the motor and gearbox of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707 that you referenced. This comes with a manual override crank in the event of an issue with powering the jacks but there is also a manual version of setup as part # UF39-941704.
    view full answer...
    Image 1 for
  • Determining If Ultra-Fab Power Twin II Manual Stabilizer UF39-941704 Fits 2019 Coachmen Apex Nano
    Since the Ultra-Fab Power Twin II Manual Stabilizer System # UF39-941704 you were looking at is adjustable it is likely that it will fit your 2019 Coachmen Apex Nano 193 BH, but the only way to be sure is to measure the frame of your trailer. The # UF39-941704 is adjustable to fit frames that are 48" to 80" wide so as long as your frame matches that width you will have no problems. I included a video review of the # UF39-941704 for you to take a look at.
    view full answer...
  • Can I Use a Power Drill To Raise and Lower Ultra-Fab Power Twin II Manual Stabilizer
    I contact Ultra-fab and since the socket on the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs part # UF39-941704 is not a standard hex socket head there is not a way to raise and lower the stabilizer with a power drill. The socket on the stabilizer requires the rod to be inside the socket for it to turn. It is not the same hex head that you would find on an ultra-fab scissor jack like part # UF48-979006. The manual crank can be a lot of work which is why I recommend to...
    view full answer...
  • Can Ultra-Fab Power Twin II Stabilizer Jacks be Used on a 2017 Minnie Winnie 31K
    The Ultra-Fab stabilizers # UF39-941705 and # UF39-941704 are very similar and have all of the same specs. But there is one important difference. Set # UF39-941704 is manually operated and # UF39-941705 comes with 2 motors for electric operation. It might be possible to install a set on your 2017 Minnie Winnie 31K but there isn't a lot of space on the underside of that RV so it is possible, even likely, that the stabilizers will not fit. When fully retracted the stabilizers will hang...
    view full answer...
  • Recommended Stabilizer Jacks for 20 Foot Enclosed Car Hauler
    For the stabilization you are seeking, I recommend the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704 or the Lippert Components High-Speed Power Stabilizer Jack - 30" Lift # LC298707. These will be superior to 4 independent stabilizer jacks and most likely have more lifting height. The recommended stabilizer jacks will give you cross frame support so you will have the frame support from both sides as you drive your vehicle on and off...
    view full answer...
  • Recommended Largest Stabilizer Jacks For Jayco Octain Trailer
    For your Jayco Octain, I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031. The overall length of the mounting plate is 7-1/4 inches, and the width is 3-1/2 inches. I've attached measurements in the attached photo to assist. If you want an even more stable system, I recommend the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs # UF39-941705 or the manual crank version # UF39-941704. These systems are adjustable...
    view full answer...
    Image 1 for
  • Can Power Drill be Used to Raise/Lower Ultra Fab Power Twin II Manual Stabilizer
    Hey Matt, we contact Ultra-fab in the past with this question and since the socket on the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs part # UF39-941704 is not a standard hex socket head there is not a way to raise and lower the stabilizer with a power drill. The socket on the stabilizer requires the rod to be inside the socket for it to turn. With that said there might be a socket size that fits close enough that you could use to get the legs to travel quickly when...
    view full answer...
  • Recommended Stabilizing Jacks For A 2018 CrossRoads Zinger Travel Trailer
    Looking through the models at that length it appears you'll be under 10,000lbs so the best option is going to be the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136. This system is fully automatic and can make stabilizer and leveling your trailer as easy as pressing a button and will have everything you need all in one kit. Because of this it is a bit steep price-wise. If you're not looking to spend as much then you'd want to go with the Electric...
    view full answer...


< Previous
12




Info for this part was:

Employee Lindsey S
Written by:
Lindsey S
Employee Michael H
Expert Research:
Michael H
Employee Jameson C
Expert Research:
Jameson C
Employee Jeffrey L
Expert Research:
Jeffrey L
Employee Dustin K
Video Edited:
Dustin K
Employee Randy B
Installed by:
Randy B
Employee Wilson B
Updated by:
Wilson B
Employee Halie H
Updated by:
Halie H
Employee Isabelle B
Updated by:
Isabelle B
Employee Noah M
Updated by:
Noah M
Employee Eric H
Updated by:
Eric H
Employee Zach D
Video by:
Zach D

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.