#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter

See what our Experts say about this TruRyde Trailer Spindles

• How To Fill Dexter EZ-Lube Spindle/Hubs With Grease And How Often Should They Be Filled?
  The spindle on your Dexter axle is going to be similar to the #84 E-Z Lube Spindle # TRU74FR in the image below. You can see there is a hole in the spindle where the grease will push through into your inner bearing. From there it will move along the spindle to the outer bearing where you will see the grease begin to push out the bearing and fill the grease cap. When filling you will want to turn the hub to ensure grease gets pushed through the entire inner bearing. This process should be...
  view full answer...
  
• Can Trailer Axle Spindle be Replaced
  You can replace the spindle of your axle but you would need to know the axle capacity to pick out the correct one. For a 3,500 lb axle the correct spindle would be the part # TRU74FR or if you have a 5.2k to 7k axle you'd want the part # TRU37FR.
  view full answer...
• Does 3,500 lb E-Z Lube Spindle Work With 3,500 lb DeeMaxx Disc Brake Kit
  Hey Will, I'm happy to say the answer is yes, the 3,500 lb DeeMaxx Disc Brake Kit # DE66YR is a fit for the #84 E-Z Lube Spindle # TRU74FR. The DeeMaxx hubs fit the spindle, and the grease cap on them has a rubber plug that you remove to easily access the grease zerk on the spindle.
  view full answer...
• Hub/Drum and Brake Assemblies that Fit 3,500 lb Spindle # TRU74FR
  Yes, everything you mentioned is compatible. The spindle part # TRU74FR is compatible with the hub/drum part # AKHD-545-35-EZ-K which is also compatible with the brake assembly set you mentioned of # AKEBRK-35-SA. The bearing kit part # BK2-100 is correct too but the hubs already come with them so they would not be needed.
  view full answer...
• Spindles and Hubs To Update 1972 Sanger Boat Trailer To Currently Used Sized Bearings
  You are going to want to update the spindles on your 1972 Sanger boat trailer to the more common Spindle # TRU74FR. This will give you the current common bearing sizes for a typical 3,500lb axle as we do not carry either of your bearing sizes. You will need to pair the new spindles with new hubs. We have either an Idler Hub # AKIHUB-545-35-EZ-K or Hub/Drum # AKHD-545-35-G-EZ-K which comes complete with bearings. These both have the 5 on 4-1/2" bolt pattern. If your trailer has a different...
  view full answer...
• Can Tang Washer Be Switched to Something Easier for 3,500 lb Axle
  Thanks for reaching out, Don! Your Kodiak 10" Hub-and-Rotor Assembly # KHR10D fits on a #84 Spindle like part # TRU74FR. You can swap over to the Spindle Nut Kit for EZ Lube Axles # RG05-100 which is a much more simple design. A lot of people have complained about the tang washer setup so you're definitely not alone in your feelings towards it!
  view full answer...
• What To Do If No Hub Has Inner Bearing L45449
  Hi Anthony, I'm sorry to say there are just no trailer hubs that have an L45449 bearing, or one with an equivalent size bearing to fit the spindle. The only option really is to replace the spindle with one that has common bearing sizes, and this will depend on the capacity of your axles. For example, if you have 3,500 lb axles you could use Spindle # TRU74FR with hub # AKIHUB-545-35-EZ-K. Or for 2,000 lb axles you could go with Spindle # TRU44FR and hub # 8-259-5UC1-EZ. I have added...
  view full answer...
• Availability Of A Trailer Hub With 1.25" And 0.75" Bearings
  We do carry one hub that fits your description with part # DX22XR. This is a 5 on 4-1/2" idler hub that uses the # LM67048 (1.25" inner diameter) inner bearing, and a # LM11949 (0.75" inner diameter) outer bearing. This is a fairly uncommon bearing combination, this is going to be the only hub we have available with those sizes.
  view full answer...
• New Brakes And Hubs For A Trailer That Uses Timken M12649 And LM12749 Bearings
  Hello Ron, thanks for reaching out. After looking at your pictures and looking over the info you provided, I do have a solution for you, but I do have to recommend that you replace the brakes, hubs and drums. You will likely need to replace the spindles also, if not the entire axle. The Timken M12649 and LM12749 bearings are not used in trailer manufacturing anymore, and while bearing replacements may be available elsewhere, we unfortunately do not carry them here. The same will go for...
  view full answer...
• Replacement Axle for 1969 Aristocrat Trailer With 4" Drop Spindle and Electric Brakes
  We have the Timbren Axle-Less Trailer Suspension System # A35RD545E you can use to replace your current axle. We do not currently carry a traditional axle that matches your dimensions and one would have to be custom made. This system includes all new electric trailer brakes and hubs. It has a 4" axle drop which places the axle center line 1/4" below the frame. Each side will bolt to the frame resulting in a independent suspension and the progressive rate springs are superior to traditional...
  view full answer...
  
• 3,500 lb Spindle Recommendation for Boat Trailer
  We do not have the axle you are looking for, but we do have 3,500 lb spindles that may be just what you need. The part # TRU74FR is an EZ lube spindle with a 3,500 lb capacity. This would fit standard 3,500 lb hubs as well. Trailer spindles should only be installed by a qualified fabricator with trailer axle experience who has the necessary equipment to square up a trailer spindle. It's not a project for someone who's pretty good at welding since if the spindle is off by just a little...
  view full answer...
• Replacement Hub Options For Trailer Hub Using L67048 Inner/Outer Bearings w/5 on 4-1/2 Bolt Pattern
  While we do have the Bearing # LM67048 and Race # LM67010 your hub uses, we do not have a hub for your axle. You can have the more common #84 Spindle # TRU74FR welded in place of your current spindle. This will allow you to use the more common Idler Hub # AKIHUB-545-35-G-EZ-K used on 3,500lbs axles. It will also accept Brakes # AKEBRK-35-SA and a Hub/Drum # AKHD-545-35-EZ-K if you will need brakes on your trailer.
  view full answer...
• How to Determine Correct Replacement Trailer Hub and Spindle
  We can get your trailer rolling again, and to get the correct replacement hub and spindle, you will just need to take a look at a couple things and get some measurements. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If you are unable to find them, you need to use digital caliper and measure your spindle to the thousandths of an inch where the bearings...
  view full answer...
  
• Distance From End of Spindle to Face of Brake Flange
  The distance from the end of the spindle to the face of the brake flange on the #84 E-Z Lube Spindle w/ Brake Flange # TRU74FR is 5-3/8". See the diagram below which shows this measurement.
  view full answer...
  
• Replacement EZ Lube Spindle For 3,500 LB Axle
  The EZ Lube Trailer Spindle we carry for a 3,500 lb axle is the TruRyde Spindle, part # TRU74FR. This spindle includes the nut and washers. The overall length of this spindle is 9 inches. This spindle is compatible with # L44649 outer and # L68149 inner bearings, and has a The bearing kit that would work with this spindle is part # BK2-100. All of the spindles we carry are a weld-on application. Please keep in mind that installing the spindle requires welding it to the axle by a certified...
  view full answer...
• Is an Oil Bath System Compatible with EZ Lube Spindle # TRU74FR
  Yes, you should have no problems using an Oil Bath System, like part # XLPROLUBE1980KIT, with a number 84 EZ Lube Spindle, like part # TRU74FR. A few things to keep in mind when installing an oil bath system. You will want to make sure that everything is sealed up properly because oil is a liquid and if you have a major leak you will lose your lubrication. When you install the body and cap you will need to make sure that it is installed all the way in your hub and is not crooked. If you...
  view full answer...
• How to Pick Out Hub/Bearings and Leaf Springs for 2003 Yacht Club Trailer
  I really wish it was that easy, but we don't have a way to look up the VIN of a trailer and determine what axle the trailer had. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out. Next thing you will need to know...
  view full answer...
  
• What Spindle Works with the Kodiak Disk Brake Assembly # K1HR35D?
  For the Kodiak Disc Brake Assembly - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs # K1HR35D, you need a Dexter #84 Spindle like the #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter # TRU24FR or the #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter # TRU74FR. It is important to note that the spindle must be welded perfectly square onto the axle. If the spindle is even slightly lopsided, you will not have an even wheel surface for the trailer. We here...
  view full answer...
  
• Replacement Spindles & Hubs for 1973 American Boat Trailer With Obsolete Hub & LM12749 Outer Bearing
  You are going to want to replace the Spindles # TRU74FR on your 1973 American boat trailer since your spindles are obsolete and we do not carry a replacement hub for this size axle. With the new spindles you will be able to use the Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-G-EZ-K. This hub is galvanized for better corrosion resistance. It also has a removable plug on the grease cap which will allow you to easily add grease to the grease zerk on the end of the new spindles.
  view full answer...
• Inner Bearing to Brake Flange Dimension of # 84 Spindle TRU74FR
  The distance from the end of where the inner bearing sits to the brake mounting flange is 1-1/4 inches, as shown in the provided photo. I've linked to a product description video for the spindle you inquired about.
  view full answer...
  
• Is There a Replacement Spindle For a Dexter D44, 4400LB Trailer Axle?
  My recommendation is to replace your axle with a 5,200lb like # e55SR as the 4,400lb spindle is so uncommon they are not readily available. This will give you stronger components to lessen the chance of you having to replace a spindle in the future. If you can provide me with the dimensions for your axle I can verify the correct replacement for your D44 axle. The #84 E-Z Lube Spindle # TRU74FR while similar has a narrower diameter of 1-1/16" for the outer bearing where a 4,400lb uses...
  view full answer...
• Flange Bolt Pattern and Distance From Flange To Rear Of #84 E-Z Lube Spindle TRU74FR
  The #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter # TRU74FR you were looking at has a 4 bolt mounting flange that has holes 2-7/8" apart on center, and from the outside edge of the flange to the end of the spindle is 3-1/4" as shown in the included diagram. This spindle will work perfectly with a 10" rotor. I included a video of the # TRU74FR for you to take a look at.
  view full answer...
  
• Replacement Spindle For a Lippert LCI35 Diamond Torsion Axle On a 2021 Forest River R-Pod 196
  The #84 E-Z Lube Spindle # TRU74FR is the same size spindle uses on your Lippert Torsion Axle. The stub is 1-3/4" diameter and 4-1/4" long. You will need to compare this to the size used on your 2021 Forest River R-Pod 196 to determine if any modification will be needed.
  view full answer...
• Replacement Trailer Spindles to Allow Installation of Different Hubs
  All of the trailer spindles we sell are weld-on types, including those with brake flanges like TruRyde # TRU74FR that fits 1.75-inch diameter axles. The largest diameter spindle we sell is for a 2-1/4-inch axle beam, part # TRU37FR; this can be seen on the link provided. This spindle is for a 5200-lb axle and it has a 5-bolt brake mounting flange. It is almost surely going to be easier and less expensive for you to replace your axles than to have a professional welder install new spindles...
  view full answer...

Do you have a question about this Trailer Spindle?