Arrives before Christmas 
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.
Features:
Specs:
You can adjust the gain (also known as output) with the thumbwheel on the front of the controller. Gain lets you set the maximum amount of power that will be applied to your trailer's brakes. A heavier trailer will need more power to achieve smooth, safe braking, while a lighter trailer will need less. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes.
The boost setting controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does.
Depending on the level of boost, your trailer brakes can start at either 13 percent or 25 percent of the set gain. What this means is that, instead of starting at 0, the brakes will start at 25 percent and get to100 percent sooner. This keeps the trailer from pushing your tow vehicle forward.
If your trailer weighs less than your tow vehicle, no boost is needed. But, if you want your trailer to lead the braking, you can select level B1.
Boost Levels:
| Approximate Gross Trailer Weight | Boost Level | Increase in Initial Power Output |
|---|---|---|
| Less than tow vehicle GVW | B1 | 13% |
| Equal to tow vehicle GVW | B1 or B2 | 13% or 25% |
| Up to 25% more than tow vehicle GVW | B2 or B3* | 25% |
| Up to 40% more than tow vehicle GVW | B3* | 25% |
*Both B2 and B3 offer a 25-percent boost in initial power. But the braking curve for B3 is more aggressive than that of B2. This means that, even though you will start out with the same intensity when using these boost levels, you will get an overall more aggressive braking experience with the higher level. So if you use B3, you will reach maximum braking sooner than if you use B2.
Safety Features
The Prodigy P2 offers key safety features to prevent damage to various components of your towing setup. Integrated reverse battery protection shields the brake controller and your trailer's breakaway system from shorts. When the P2 is not in use, it will be in power-saving mode. In this setting, it draws only 3.6 milliamps, minimizing drain on your vehicle's battery.
The P2 also comes equipped with a hold feature to prevent wear on your brakes. When you're waiting at a red light, you don't need your trailer brakes on at full power. The longer you sit there, the more they will overheat. But with the P2, any time your tow vehicle and trailer are at a standstill with the brakes applied for more than 5 seconds, the hold feature will kick on and reduce power to just 25 percent. This will keep your trailer in place while saving your brakes.
The P2 keeps the manual override within easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just twist the rotary-style lever from right to left. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
The Prodigy P2 also offers diagnostics such as:
The self-leveling feature of the P2 ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at any vertical angle, and the controller will level itself automatically thanks to its 360-degree rotational range. This makes the installation that much easier. But keep in mind that the P2 must be horizontally level and parallel with the direction of travel to work correctly.
Installation is a snap. After mounting the P2 unit in your cab using the included bracket, just plug the custom harness directly into your vehicle. The other end plugs into the brake controller. To remove the P2 for storage when you're not using it, just unplug the unit and slide it out of the bracket. With a replacement wiring harness (sold separately) and replacement bracket (P7685 - sold separately), you can even transfer the Prodigy P2 to another vehicle.
Note: If you don't already have a 7-way plug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
The Tekonsha Prodigy P2 brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Prodigy P2 uses an internal inertia sensor to detect how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
Alternate Instructions
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
When it comes to choosing a brake controller, a lot of them are gonna look very much the same. And two of them that I really like are from Tekonsha. We have the Prodigy P2 and the Prodigy P3. So, they look very similar, but they do have quite a few differences and we're hoping to break that down, that way you can decide which one's best for you. Here we have our P3 installed and really it comes down to it has more bells and whistles than the P2, otherwise it's pretty much the same controller. The P3 does have a nicer/easier to use display.
It's a little bit more user friendly. It uses some icons here that, you know, show you a trailer and that way you know pretty quickly what boost level you're at and it's really easy to read. It's a nice digital display and you can change a lot of that. Also, it has a little bit more diagnostics. So as far as, instead of just having error code with the P2, this one will actually tell you exactly what it is and there's a host of diagnostics so that way you can look at it.
You won't have to troubleshoot the code by looking at the owner's manual. It'll tell you right away what's happening. The P3 is also really nice if you have a bunch of trailers in your fleet, you can set up presets, up to five of 'em, and that way when you hook up to said trailer, you can select that and it's gonna be preset to the boost settings and also the gain that you may have dialed in. That way you just hook up and you'll be ready to go. Multiple trailer settings are gonna be nice, especially if you have a work truck and you're hooking up to a bunch of different trailers, you can get that dialed in, but if you tow the same trailer over and over, or you know that you're only gonna have one trailer long term or maybe two, that's really not gonna be a function that is necessary.
Now with the P2 installed, you can see right away that the display is obviously not as fancy as the P3, but you again have all the same functionality. There are less buttons, so that kind of keeps it simple. If you just need a brake controller, this is a great option. You still have your power knob, you have your boost button, and you still have essentially the same manual override, which I do like on the Tekonshas, you have a nice modulation here. But really when it boils down to it, they are very, very similar.
The size is gonna be almost identical. They're gonna mount up the same, they're gonna install the same. Again, you have that same proportional here. They both work for one to four axles. They're both proportional. So pretty much the same thing, just more bells and whistles on the P3. If it's something that you're gonna wanna keep for a long time on your vehicle, a P3 is pretty sharp. I do like the display, and something to think about too, you can always take a brake controller from one vehicle to the next, so, but if you're just need to tow a trailer and you need a brake controller, P2 you're not gonna go wrong with. I just like the fact that there is diagnostics that are a little bit more straightforward with the P3. And if you're worried about if it's gonna work with your trailer, they're both gonna work with the same kinds of trailers. You can have electric brakes, you can have hydraulic brakes, it doesn't matter. These are gonna work with either one. So hopefully this video helps break down some of the similarities and differences to help you decide which Tekonsha Prodigy Brake Controller is gonna be best for your needs.
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.I bought this to replace a Curt Triflex controller that went bad after 3 years. They both did/do a great job, but I like a couple features of this unit better - the blue readout is easier (at least for me) to read and the boost option is nice to have as I live in the mountains and it helps on the steep downhills, helping save my tow vehicle brakes a bit. It fits nicely under my dash and I don't bang my knee on it entering my vehicle. Recommended!
I purchased the brake controller and wiring harness from you all and installed it watching the video on your website. I followed the instructions to an absolute T. Got everything ready and tested the product and got an SH error code for the blue brake wire shorting out. I pinned and measured resistance and everything was coming back fine (4+ ohms resistance). I then hooked a power prope to it to find the short along the frame and nothing. I had power from the female connector all the way up to the brake controller. After 4 hours of troubleshooting, I found that the female trailer connector was shorted internally. See the attached picture. The blue and green ring terminals inside of the female trailer connector were touching. Replaced the trailer connector and now all is well.
Was plug and play after adding one 30 amp fuse to the under hood fuse panel that we already anticipated.
This has been an amazing company to work with. Their chat (a live person!) had the correct list of products I needed for my truck. In less than 2 minutes. Their follow up and dates promised were on target-every time!! I've now used the brakes on 2 trips and they work correctly and are easy to adjust as needed. It has been a pleasure in every way to do business with etrailer!!
I called eTrailer on a Sunday afternoon and customer service picked up the phone on the first ring. Brandy helped me select the right harness adapter for my Tekonsha trailer brake. I got an email that the package arrived before I even checked the mail. I was able to install the set in about ten minutes. Awesome service, all other retailers should be this good!
I have an '02 Excursion and a Tekonsha brake controller. This was as easy as plug and play.
I have a Tekonsha controller on my 2001 Chevy Silverado and it worked like a charm for over 18 years.I'm sure that the new Prodigy P2 will do the same.
The plug adapter worked well and made installation easy. However I tried to reach out to Robert S at etrailer to find out what to do about an annoying rattling noise that it makes driving down the road when the road is not perfectly smooth. Even light irregularities in the pavement causes the brake controller switch to rattle. I have not heard anything back from Robert S at etrailer.com. So I sent a "1" rating on the brake controller switch because of this annoying rattling noise. I'm about to just disconnect it and leave it in the glove box and connect it back when or if I ever need it. Any comments?
This is the second one I purchased. The first was 10 years ago and installed in my 06 GMC. It has worked flawlessly allowing for safe and smooth stops from normal braking to a few of the panic stops that had to made over the years. The new owner of the truck likes the way it works too. I have multiple trailers and with one initial setup on the lightest trailer was able to tow all of them without changing anything but the boost setting to compensate for the different trailer weights.
When needing for a controller for my 07 Silverado there was no other unit that would fill the bill. This P2 looks the same except for the blue display instead of the red. The install took 20 minutes using the direct fit cable ordered with the controller. Setup was easy as with the first unit. I wanted the placement above the parking brake pedal so the OBD II connecter had to be moved. I did the same with the 06 GMC. It is a comfortable place to reach and it keeps the light away from the passenger's eyes at night.
As good as the Tekonsha controller is it is even a sweeter deal buying it from etrailer. The quick shipping, excellent pricing and knowledgeable staff are second to none in customer service.
Installed this in my 2015 Jeep Wrangler Unlimited Sport. I thought that I would add some input on installation that would help others.
I found a way to route the power distribution wires in the frame of the Jeep that did not require the use of a fish tape. If you look at the frame just behind the rear tire you will see a hole in the face of the frame. Start pushing the wire bundle foreword. It will rise up and over the U shaped frame portion of the rear axle and then down along the passenger compartment area. About there, you will be running out of pushing stiffness. Look for the wire bundle to appear at a similar hole in the frame in that area. Grab it a and pull out approximately 4 feet and then push it right back in the same hole going foreword. This time you will look for the wire bundle to appear at again a similar hole just foreword of the driver compartment. Now is the time to grab it and start heading up to the engine compartment outside the frame. Do the same procedure for the wire going aft for the plug end of the installation. For the wires going through the firewall, Jeep has conveniently added a nice foam lined hole to route wires through. You will see this hole position in the attached photo with a green wire coming through. The plastic cover around the steering column pulls down from the top and hinges at the bottom. Remove the metal plate with two bolts to get to the brake switch. Twist and pull the brake switch out foreword and go for the brown stripped wire as your brake circuit. Do order the LONG frame bracket adapter for the switch plug at the rear. To drill the steel for the supplied plug bracket just takes too long. Now that you have it installed you will notice that the power will remain on the unit after you turn the key off. Don't sweat this as it will not stay on long. I doubt a few milliamps draw is going to kill your battery!
I was a bit surprised by slow shipping and poor tracking but it finally made it so I'm a happy camper in the end. I expect this P2 to last. It's a duplicate of one in another truck, first purchased in 2005, and migrated to second and third trucks in the almost two decades since. That one's still working perfectly but now that I'm at a point with two trucks in my fleet I didn't want to swap it back and forth and have tweak gain. That's more about me than the product I suppose but it gives an idea that it's solid product all the same. As for etrailer service I admit I was a little disappointed but stuff happens so I'm over it.
I ordered the trailer brake adapter harness for my 2010 full size Range Rover.
It fit great and its well made to do the swap,
for others that will read this here is how.
I found the brake connector in the truck was hidden behind the fat harness thats next to the inside left kick panel, just behind the hood release panel
By pulling on the OBD 2 wire harness, I found it was tied to the OBD harness.
Some say that the connector is on the left side of the steering column , in my truck is was on the far side of the fat harness so it was hard to see.
I had to remove the left side console, I removed the screw, then pulled the bottom of the wood panel towards the left door, the 2 pins released, then the panel slides to the rear of the truck to dislodge the top pin.
5 screws secured the lower panel , remove the lamp ,unplug it,
then remove the OBD 2 connector from its mount , slide the gray collar to the left kick panel then the harness pushes up out of its holder.
Plug in your new adapter harness for your trailer brake controller,
Assemble is the reverse of taking it apart.
in the picture the new harness is connected to the gray connector
I ordered a Draw-Tite 5535 Brake Controller & adapter cable 3035-P from etrailer for my 2011 Ford Holiday Rambler F53 Chassis RV to tow my Tow Dolly with electric brakes. I ordered the parts on Saturday and received them on Thursday using economy shipping rate which was great. I received just what I ordered and installed them today (Friday) everything worked perfect and the install was very quick and easy.
0543.jpg is my Brake Controller 5535.
0544.jpg is my Adapter Cable 3035-P.
0548.jpg is a picture of the Ford Factory cable in the RV.
0535.jpg is a picture of the end of the Ford Factory cable that the Adapter Cable 3035-P plugs into.
0550.jpg is a picture of the Brake Controller 5535 installed to the right of the steering wheel.
The online video showing the installation of the Prodigy P2 trailer brake control into a 2011 Ford Ranger was excellent! It made the installation into my Ranger simple and straight forth.
I have yet to hook up to my travel Trailer and adjust it for brake setting, but all readout displays thus far are as stated in the instructions.
Having previously installed the trailer connector, I did not purchase the installation kit and in retrospect for cost effective and simplicity would recommend anyone to purchase the kit along with the controller.
I believe I am going to be very pleased with this product.
Thank you
Multiple products which I purchased from Etrailer to upgrade my Capri Rodeo truck camper. The steps are well made, easy to setup, and extremely helpful in entering and exiting. I set them next to the door when travelling. The trailer brake controller smoothed out the jerking that was a problem for far too long and simple to install. The vent cover was definitely needed as the original had a hole in it. The removal and replacement went well.
I'd ordered the Tekonsha Prodigy P2 Proportional Trailer Brake Controller (1 to 4 Axles ) on a Monday with a Wednesday delivery date of two days, as I'd specified. I have a Lincoln Navigator that had the factory installed heavy tow package. I had also ordered the adapter connector for Prodigy P2 controller to the Navigator's factory plugin. The entire install took me 15 minutes. I found the video review of the controller quite helpful as it demonstrated how to static set the controller's setting before drive trials and how to set the "boost" settings. Good price and very easy to install.
Connected to factory wiring and to Tekonsha Prodigy P3 Trailer Brake Controller without any issues.
I haven't towed with the it yet. But installation on my 2007 Ford F150 was pretty simple. The plastic panel I attached it to had steel behind it. So I removed the plastic panel, mounted the bracket, then trimmed the excess length off the screws, and reinstalled the panel. The wiring harness plugged right into the truck's plug under the steering wheel. It seems like a great product, and having the specifc wiring harness for my truck made it simple to install. Sheila was very helpful too. Thanks.
very nice controller, very smooth and you don't have to mount it flat!! e trailer is the best company i ever worked with. they have pics, video, email support(exellent) and just flat out make it easy for you to do it yourself instead of paying some dirt bag $300 to install at your local trailer shop. i also installed kit #ETBC7 and once agian it was awesome. COMPLETE with DETAILED directions. i'm not a mechanic or hack employee at local trailer shop....BUT dealing with etrailer and there parts made my install very easy and CLEAN!!!
It's a lifesaver. Literally. I installed it on my enclosed trailer that I tow with my motorhome. I had no idea such a thing existed. Etrailer introduced me to that amazing product by an email. Needless to say I purchased it right away. Guys, if you tow anything, this product is A Must. Personal experience, before (very bad) and after (very happy) of this installation. Thank you.
Brake controller was very easy to install on a 2014 Suburban. It works great with both of my trailers.
Quick delivery. Great service.
Plugged in the controller, no problem at all. Still working great!
Works very well for a year now. No hassle installation and zero issues. Easy to adjust for hauling different trailers. I am happy with the purchase.
Great product! Since I pull my goose neck with electric brakes, with my semi truck tractor, it acts as a interface between the air brakes and the electric trailer brakes, and acts as a Johnson bar if I need to get the trailer back under control.
Brake controller is a little finicky but is doing the job as supposed to do.
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.