Friction in brackets and in head works to prevent and correct trailer sway. Chainless brackets with automotive-style friction pads hold spring bars firmly in place to help keep trailer in line with your tow vehicle. Adjustable shank included.
Features:
Specs:
| Included w/ System | Required - Sold Separately | Optional Add-Ons |
|---|---|---|
|
| n/a |
Create a stable ride for your tow vehicle and trailer with a weight distribution hitch. Adding spring bars to your towing system applies leverage, which transfers the load that is pushing down on the rear of your vehicle to all the axles on both your tow vehicle and your trailer, resulting in an even distribution of weight throughout. The result is a smooth, level ride, as well as the ability to tow the maximum capacity of your hitch.
The tongue weight rating is the most important factor in determining which size weight distribution system you should use. If the bars of the system you choose are rated too high for your setup, they will create a rigid ride, which can result in a bouncing trailer. If, on the other hand, the bars are not rated high enough, the system will be unable to properly distribute the weight, rendering it virtually useless.
To determine the proper weight rating for a weight distribution system, you must first determine your trailer's tongue weight. Then add to that the weight of the cargo behind the rear axle of your tow vehicle. These two measurements make up the tongue weight rating for a weight distribution system.
Integrated Dependent Sway Control
The Steadi-Flex weight distribution system works to stop trailer sway before it begins. This is achieved in 2 ways. First, the system head is designed to firmly hold the spring bars in place to provide tight resistance and help ensure that your trailer tracks behind your vehicle. Second, the spring bar brackets that mount on your trailer's frame produce friction with the bars whenever any side-to-side motion occurs. This keeps the bars from moving, also helping to hold your trailer in a straight line.
System Head with Steel-on-Steel Friction
The head of the Steadi-Flex system firmly holds the spring bars in place at the hitch point. This tight hold helps to keep the bars from moving, which in turn helps to ensure that the trailer is held firmly in place behind your vehicle. If any sway or side-to-side movement does occur, the spring bars will move only slightly inside of the system's head. This steel-on-steel contact produces frictional resistance to limit further side-to-side motion of the bars, limiting the motion of your trailer in the process. The Steadi-Flex head is wider than most weight distribution heads. This design allows for greater surface area for the spring bars to move against. This makes it easier to produce the friction that resists sway.
Sway Control Brackets with Automotive-Grade Friction Material
The spring bars attach to the trailer frame with fixed, sturdy steel brackets. They sit on top of the brackets instead of being suspended by chains like the bars that are on traditional weight distribution systems. Chain suspensions typically allow a good deal of side-to-side play in the system. Because the Steadi-Flex has brackets in place of chains, that unwanted movement of the spring bars is eliminated. This helps to keep your trailer in line behind your vehicle. In addition, these brackets create friction to limit any side-to-side movement that may occur. When each spring bar on the Steadi-Flex system moves within the bracket, it rubs along the surface of the bracket, creating friction. This resistance limits the movement of the spring bar, thus preventing further side-to-side movement of the trailer.
Most systems with sway control brackets use bare steel brackets to create friction with the steel bars. Steel-on-steel friction typically causes a much louder ride, and it can result in wear and tear on the brackets themselves. The Steadi-Flex brackets, on the other hand, are lined with automotive-grade friction material. This material is more abrasive than bare steel, which allows more friction to build up faster and easier. The long-lasting friction material also reduces the banging noise created by the bars hitting the inside of the steel brackets. This provides a quieter ride while towing.
Fast, Easy Installation
The Steadi-Flex system is easy to install and set up. On the trailer side, simply clamp the spring bar brackets around your trailer's frame. Then prepare your vehicle by sliding the included shank into your 2" x 2" hitch receiver, and bolt on the head. The system head can be easily adjusted to achieve the proper angle and optimum leverage for your specific setup. No drilling is required to install this weight distribution system.
Head Tilt Adjustment
The head of the Steadi-Flex can be easily adjusted for the best possible angle for your towing setup. Adjusting the head lets you fine-tune the system's leverage so that you can get the best distribution of weight possible. Traditional head tilt adjustment methods require that the head be disassembled so that stackable washers inside the head can be either removed or added on. But with the Steadi-Flex, there are external, toothed washers on either side of the head that make it easy to change the tilt. Simply position the head in one of the preset angles based on your hitch's tongue weight, then bolt it in place, tightening the washers as you do so. Once the head is sitting at the correct angle, tighten the internal adjustment bolt to secure the platform in place.
Tapered Spring Bars
The spring bars of the Steadi-Flex system slide into the weight distribution head for quick, easy installation. With a tapered design and hot rolled steel construction, these bars offer superior flex to evenly distribute the weight between your tow vehicle and your trailer.
The bars easily pin into place inside the system head - no need to torque or re-torque any trunnion bolts to adjust the tension. With fewer parts to manage, installing and maintaining the Steadi-Flex is simple.
Adjustable, Clamp-On Brackets
The spring bar brackets simply clamp around your trailer's frame - no drilling required. These brackets are designed to be positioned 27" to 32" back from your coupler and they can fit a wide range of frame sizes and can even be used on a trailer with a bottom-mounted coupler.
While other brackets use L-pins to secure the spring bars in place on the brackets, the hinged Steadi-Flex brackets close completely around the spring bars. As a result, you can have greater piece of mind knowing that the spring bars are secure, all without the hassle of using and possibly losing L-pins and any extra hardware.
California residents: click here
Average Customer Rating: 4.7 out of 5 stars (231 Customer Reviews)
Friction in brackets and in head works to prevent and correct trailer sway. Chainless brackets with automotive-style friction pads hold spring bars firmly in place to help keep trailer in line with your tow vehicle. Adjustable shank included.
Just as I expected.
Fast delivery and good quality products.
Awesome product variety and great communication! Will shop here again
Placed my order on Wednesday and Received it on Friday. And everything seems to be just as expected. Thanks
Delivered on time and quality seems good. Thank you
Delivered very fast. Great price and great customer service. Will definitely be buying again
Works well
exact what i ordered very good quality heavy duty,fast shipment thank you
works great!!!love it
Tows great. No sway.
Easy to put together, works great on my camper.
Great product, easy install. Fast shipping, thanks
Do you have a question about this Weight Distribution Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.