Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Cross brace bars permanently attach to your fifth wheel's landing gear to reduce your trailer's movement while parked. After installation, the braces will extend and retract with your landing gear. Hand-tighten tubes to increase stability.
Features:
Specs:
Note: This stabilizer will not work with round, hydraulic landing gear legs.
Average Customer Rating: 4.5 out of 5 stars (239 Customer Reviews)
Cross brace bars permanently attach to your fifth wheel's landing gear to reduce your trailer's movement while parked. After installation, the braces will extend and retract with your landing gear. Hand-tighten tubes to increase stability.
I ordered the MoRyde 5th wheel cross brace to stop the shaking in our 26' Winnebago Micro Minnie. The brace was easy to install and does a great job of stopping the trailer shaking; I don't even need to twist it tight. The downside is that it was too long to fit between my jacks so I had to take it to a machine shop and pay them to shorten each brace by 6".
The cross brace worked great. It took the shake out of camper. Would highly recommend them. Installation was easy. Thanks for a great product.
Gary
8/15/2023
Works great. Would buy again. Thanks
Haven't had a chance to install it yet, but based on the reviews and a basic understanding of physics, I believe this product will dramatically increase the stability of our 5th wheel.
Matt G.
3/19/2024
I just made a comment yesterday to my wife about how much of a difference the cross braces make. We were in New Mexico with sustained winds of 30-40 mph. While prepping to leave our site, I removed the braces and immediately the fifth wheel started to move with the wind. After one year, I still highly recommend this product.
Money well spent! Got rid of the tripod that we always had to set up under the king pin. Super easy install, makes the camper way more stable and we aren’t constantly tripping over the tripod anymore. Highly recommend. Only regret is not buying one sooner!
Great product. Easy to install and easy to use. Paired with a 5th Wheel King Pin Tripod Stabilizer. Helped to stabilize the front on my 5th wheel trailer. Went front lots of sway to almost zero sway.
These work INCREDIBLY well. The install was easy AFTER I got the correct instructions from etrailer. The instructions that came in the box were horrible, missed steps and no use instructions. After the DL from etrailer, all went well. About 45 minutes start to finish and the difference is HUGE. NO shake whatsoever. One of the best upgrades to my 5th wheel so far.
Bobby K.
10/26/2022
This produce still looks and works like new. The RV is very stable with them enabled tightened down. Very satisfied.
The initial problems with broken box and losing parts in shipping were solved early. The lacking instructions were also solved also in a timely manner. The stabilizers are installed and work as good as hoped! Now I just have to level up the 5th wheel and line up the holes put the pins in, turn until snug and I’m done.
Barry
4/12/2022
Theyve worked great until a fluke accident with road garbage. A tire tread from a semi went under my truck and hit the bracing causing one to come off at one end and the other bent. I have another ordered another because I liked it so much. It should be here this month sometime. I still think its a great product.
After getting some parts issues corrected (Thanks to Nicole and George at etrailer, and thank you Ryan at MorRyde), the installation went well. The side to side motion of the fifth wheel was essentially eliminated. This is a great product. I don’t think I need to install or use the Kingpin support that I purchased. The landing gear braces are all that’s needed. I did find that some silicone lubricant sprayed in the tubes helps with the extension and retraction of the braces. They can be a little tight due to the paint coating of the smaller inside tube. You will notice in the pictures that I chose to use the bolts instead of the pins to attach the braces to the brackets. I did this because I’m leaving the braces in place during landing gear operation (don’t forget to pull the tube lock pins), and I feel it helps to prevent thievery. The included flag to place at the landing gear control as a reminder to not operate with brace lock pins inserted, is a nice feature but my included warning flag did not include an adhesive type Velcro strip. I opted to install an electrical disconnect switch at the gear motor ground. After installing the tube lock pins, I immediately open the switch, prior to adjusting the braces at my camp spot or RV park pad. If you have a fifth wheel, I sincerely recommend this product.
The X brace installed pretty easily. I did need to get some longer hardware. The performance has been great. No issues at all.
Super easy install and works great. The movement in my fifth wheel has dropped to almost 0.
Helps a lot and easy to install and use!
D.r.
7/29/2024
Still as good as day one!
These stabilizers are the best. It takes all the sway out of the camper. Kinda a pain to install on an older camper. Will definitely buy again.
Great product. Shipped promptly. USPS shipped my order to the wrong post office and it became lost in theb system for 6 days. Stop using USPS.
Kevin
5/28/2024
The cross braces go along way to help reduce theb shake in our 5th wheel.
Jerred H.
5/30/2024
I have a 19 99 King Of the road fifth wheel installing the supports was easy due to the type of landing gear RV has had to mount them in a different position hopefully it will work well Picture attached
They work great and keep the trailer from rocking when the front legs are extended.
Thomas J.
8/21/2023
I sold the camper shortly these were installed. While I was able to use them they worked great.
All is well except that I have to completely remove it every time I transport the trailer because the landing gear are not as long as the product requires.
Robert
7/16/2023
It is a lot of work getting it on and off each time we transport the trailer
Easier to install than other brands and stabilizes the fifth wheel.
Works well. No movement now
Didn’t stop the 5th wheel camper from rocking at all.does nothing to stop the forwards or back movement.. miss the old days with the manual jacks
The installation book is missing a socket and wrench size needed to install.
The MORryde stabilizer, used to together with the XChock wheel brace, is a great combination to stop 5th wheel trailer rocking.
Must buy! We have a 36’ Forest River 5th wheel, no auto levelers. Our trailer would move side to side easily even with King pin stand. Installed this in 30 minutes. Tightened up the shafts and couldn’t budge the trailer. I’m 300lbs and put all my weight into it, my son said he could feel I was trying to move it but didn’t shake at all. Game changer. No more side to side. Can’t say enough on how much this stopped the side to side movement. So easy to install. Set up one set takes 20 seconds to tighten. Must buy if your having the same problem I was having. Wife can sleep better even when I roll to the side. No shakes!
Jeff
6/26/2022
After one year, great! No complaints at all! I can immediately tell if I don’t tighten them up when I get to out spot. Night and day difference. Highly recommend.
Easy to install, setup, and extremely s table
Works perfect! Service was great.
The product itself performs as it should once properly installed. I had the order in less than a week from Etrailer. Also, I was thankful for the great information Etrailer has posted on this product. The video showed the correct method for installation. The printed instructions for the braces don't mention the flat backing plate on the upper brackets, so I had to remove and reinstall those. Also, the bar orientation in the picture on the front of the manual is wrong. Both thin tubes should be pointed downward as in the video.
Do you have a question about this Camper Jack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
5/15/2023
I wanted to ask you a question about shortening the braces. Do you know if the machine shop just cut the open ends of the tube? Would you be able to send pictures of the modifications? I just want to make sure that it is safe for you to use. If it was just cutting the open ends of the tubes, then that is fine, however if it was more extensive then it could be problematic.